Poe powered

Barely used for 2 Voip Phones. The CNP-POEI is a Power over Ethernet Injector which can Inject power into a non-powered eternet cable and deliver Electrical Current to PoE compliant devices such as APs, IP Cameras or IP Phones, where there are no power lines or outlets available. It fully complies with IEEE af standard, and can work with all IEEE af PoE compliant PDs (Powered Devices) or PoE reciever adapters, such as Canyon’s CNP-POES. The instalation is very simple (Plug-and-play), and there is no configuration or software required. IEEE af compliant PoE Injector Delivers power up to 100 meters Auto-determine the necessary power requirements Plug-and-Play, no configuration required External power adapter supply  

The CNP-POEI is a Power over Ethernet Injector which can Inject power into a non-powered eternet cable and deliver Electrical Current to PoE compliant devices such as APs, IP Cameras or IP Phones, where there are no power lines or outlets available. It fully complies with IEEE af standard, and can work with all IEEE af PoE compliant PDs (Powered Devices) or PoE reciever adapters, such as Canyon’s CNP-POES. The instalation is very simple (Plug-and-play), and there is no configuration or software required. IEEE af compliant PoE Injector Delivers power up to 100 meters Auto-determine the necessary power requirements Plug-and-Play, no configuration required External power adapter supply  

Trendnet TPE-S44. Switch type: Unmanaged. Copper ethernet cabling technology: 100Base-TX, 10Base-T. Networking standards: IEEE 802.3, IEEE 802.3af. Supported data transfer rates: 10/100 Mbps, Maximum data transfer rate: 0.1 Gbit/s. Colour of product: Blue, Certification: FCC, CE TPE-S44 8-Port Smart Switch integrates Power over Ethernet (PoE) and network management features into a cost effective and scalable solution. The TPE-S44 reduces equipment cost by delivering data and power over existing network cable infrastructure. -Reduces equipment cost by delivering data and power over existing network cables. -4 PoE and 4 standard 10/100Mbps ports. -Flow Control for Full-Duplex mode. -IEEE 802.3af Power over Ethernet (PoE) Standard Compliant. -8 x 10/100Mbps Auto-Negotiation and Auto-MDIX Fast Ethernet RJ45 Ports. -Built-in 4 PoE Ports (Port 1 ~ Port 4). -Supports PoE Power Maximum 15.4 watts for each POE port. -Supports PoE Powered Device (PD) classification identify. -Full Wire-Speed Non-Blocking Reception and Transmission. -Store and Forward Switching Method. -96Kbytes RAM Data Buffer and 1K entries MAC Address Table. -Extensive Diagnostic LED´s on the Front Panel. -IEEE 802.3x Flow Control for Full-Duplex Mode; Back Pressure Flow Control for Half-Duplex Mode. -5-year limited warranty.

Tenda 8 -Port PoE Desktop Switch sealed in box. Features and benefits: - 9 10/100 Base-TX RJ45 ports - up to 8 ports of IEE 802.3af/802.3at devices powered - 58-watt PoE budget - Each port supports 51V DC power to PoE Powered Device - 6KV lighting protection - Extend Ethernet mode with 250 m tarnsmisiion distance - Plug and play design, no configuration required Unfortunately purchased the incorrect switch for my busines set up.

NETGEAR ProSAFE GS728TP - switch - GS728TP-RACK MOUNT or STAND ALONE PLUS SOME FLY LEADS INCLUDED PLUS GS728TP is Gigabit PoE/ PoE+ Smart Switche that comes with PoE capabilities on all ports and supports PoE+ with up to 30W of power budget on the first 8 ports, providing hardware investment protections so that the switch can support many more PoE powered devices and higher-powered devices down the road. There has also been an addition of high-powered PoE+ Smart Switch into the portfolio. It also comes with 4 dedicated Gigabit SFP ports for fiber connectivity.

Description Tenda 10/100Mbps POE Injector Tenda 10/100Mbps POE Injector PoE15F can realize the synchronous transmission of network data and power through an Ethernet cable (Cat.5 or better). The output power of each port is as high as 15W, which can be exported as PoE equipment (via RJ45 port). You can connect to ieee802.3af’s PD, such as wireless AP, IP camera, IP phone, etc. In a sense, reducing installation costs and improving network performance is a good choice. Features: Delivers power and data through one Ethernet cable for easy network extension Compatible with IEEE 802.3af compliant powered devices PoE Port Delivers power up to 100 meters Plug and Play, no configuration required Power Over Ethernet One PoE port to power connected devices for flexible network deployment IEEE 802.3af compliant Compatible with IEEE 802.3af compliant powered devices Extend Power Supply Distance of power transmission via Ethernet cable is up to 100 meters Plug and Play Hassle-free setup, no configuration required Specifications: Network standards IEEE802.3、IEEE802.3u LED Indicator Link/Act, PoE Status Interfaces 1*10/100 Base-TX Ethernet ports(Data/PoE) 1*10/100 Base-TX Ethernet ports(Data) Transmission media Recommended: CAT5/5e UTP or better Dimension 84.5mm*44mm*29.8 mm Level of protection ESD: Air discharge: ±10kV Contact discharge: ±8kV Forwarding mode Store-and-forward Transmission Rate 100Mbps PoE budget Single port: AF: 15.4W Whole device: 15W Power consumption 15W Input voltage 100－240V AC 50/60Hz 48V/0.3A DC（Power Adapter Output） Mounting Desktop mounting: support Environment Operating Temperature: 0℃~45℃ Storage Temperature: -40℃~70℃ Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Certification FCC、CE、RoHS b'/xc2/xa0' Why not browse our wide variety of Tenda Products HERE

Tenda 10/100Mbps POE Injector Tenda 10/100Mbps POE Injector PoE15F can realize the synchronous transmission of network data and power through an Ethernet cable (Cat.5 or better). The output power of each port is as high as 15W, which can be exported as PoE equipment (via RJ45 port). You can connect to ieee802.3af’s PD, such as wireless AP, IP camera, IP phone, etc. In a sense, reducing installation costs and improving network performance is a good choice. Features: Delivers power and data through one Ethernet cable for easy network extension Compatible with IEEE 802.3af compliant powered devices PoE Port Delivers power up to 100 meters Plug and Play, no configuration required Power Over Ethernet One PoE port to power connected devices for flexible network deployment IEEE 802.3af compliant Compatible with IEEE 802.3af compliant powered devices Extend Power Supply Distance of power transmission via Ethernet cable is up to 100 meters Plug and Play Hassle-free setup, no configuration required Specifications: Network standards IEEE802.3、IEEE802.3u LED Indicator Link/Act, PoE Status Interfaces 1*10/100 Base-TX Ethernet ports(Data/PoE) 1*10/100 Base-TX Ethernet ports(Data) Transmission media Recommended: CAT5/5e UTP or better Dimension 84.5mm*44mm*29.8 mm Level of protection ESD: Air discharge: ±10kV Contact discharge: ±8kV Forwarding mode Store-and-forward Transmission Rate 100Mbps PoE budget Single port: AF: 15.4W Whole device: 15W Power consumption 15W Input voltage 100－240V AC 50/60Hz 48V/0.3A DC（Power Adapter Output） Mounting Desktop mounting: support Environment Operating Temperature: 0℃~45℃ Storage Temperature: -40℃~70℃ Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Certification FCC、CE、RoHS b'/xc2/xa0' Why not browse our wide variety of Tenda Products HERE

Planet POE--Port af PoE Injector is a 4-Port IEEE af Power over Ethernet injector hub. Equipped with Base-TX Fast Ethernet ports, the POE-400 supports full 48VDC power for any remote IEEE af powered devices, such as Wireless LAN Access Points, IP phones and LAN Cameras. Supporting power supply of 70 watts, the POE-400 provides sufficient power to the 4 remote devices. There are 8 RJ-45 STP ports on the POE-400. Half of the ports on the right panel function as "Data" and the other half on the left panel function as "Data and Power". Each of the "Data and Power" ports is an injector that inserts DC Voltage into the CAT 5 cable allowing the cable between the Injector and Splitter to transfer data and power simultaneously. Specifications: Ethernet Connector: 8-Port RJ-45 STP with 4-Port "Data" & 4-Port "Data & Power", Ethernet Data Rate: Mbps (vary on Ethernet device attached), Input Voltage: DC 48V, 1.5A, Number of Devices that can be powered: 4, Ethernet Cable: TIA/EIA-568, Category 5/5e cable, LED Indicator: 1 x power, 4 x PoE ready / in-use, Operating Temperature: 0ºC ~ 50ºC, Storage Temperature: -20ºC ~ 70ºC, Humidity: 5% ~ 90% RH, Emission: FCC Class B, CE mark, Standard Compliance: iEEE Ethernet; IEEE u Fast Ethernet; IEEE af Power over Ethernet, Dimensions: HxWxD: 26 x 70 x 97 mm, Weight: 220g

This 4 port 10/100Mbps PoE switch is with 48V/1.25A external power,it provides an easier installation way for PoE devices,such as IP cameras,wireless AP,VoIP. And it can detect your PoE devices according to PoE standard.So the users do not need to worry about the PoE switch will damage their PoE devices. The max transmission distance is 100 meters with Cat5 cables. Ideally,shorter cable would reduce the power degradation over the cables; with high quality cables also can reduce power loss.Plug & play design make the installation quite easy,users do not need any configuration,which make this PoE switch a very good choice for IP cameras,wireless AP,VoIP users. IEEE 802.3af Power over Ethernet PoE compliant. Supports 10/100Mbps fast Ethernet. 48V/1.25A External power supply. Max power for single PoE port is 15.4W. Automatically detects the PoE class level of a Powered Device. 1Gbps bandwidth. Store-and-forward switching method. Plug and Play. General Quantity 1 piece Material ABS + metal Other Features Other Features Standards and protocols the IEEE 802.3 standard The IEEE 802.3 u 100 base - TX The IEEE 802.3 ab 1000 base-t The IEEE 802.3 af power Ethernet (POE) IEEE 802.3 x flow control Interface port 4 * 100 m POE (automatic negotiation, auto-mdix) Port 5 is a 10/100 MBPS uplink port Data transfer rate Ethernet: 10/100 Mbps (half/full duplex) Forward rate 148800 100 Mbps/polyphenylene sulfide (PPS)/polyphenylene sulfide (PPS), 10 Mbps, 14880 Power input: 100 ~ 50/60 V/Hz 48 v / 1.25 A external force DC48V The power supply pins (36 (12):) The index of electric power, POE/activities, link Environmental operating temperature: 0 to 40 Storage temperature: 40-70 Working humidity: 10% to 90%, without condensation Store humidity: 5% to 5%, without condensation Dimensions & Weight Dimensions 7.87 in x 7.09 in x 1.57 in (20 cm x 18 cm x 4 cm) Weight 17.64 oz (500 g) Packing List 1 * PoE switch 1 * Adapter(1m) 2 * Accessories

D-Link DGS-P 8-Port PoE | DGS-P/E Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery D-Link Product Code: DGS-P/E Availability: 47 in Stock Plug and Play operation Gigabit speed Fanless, silent operation to fit in any environment Safety function to prevent PoE overloads, protects both the switch and the connected PoE devices Cable diagnostics function to help troubleshoot wiring problems Green Ethernet technology, saves energy and increases the product's lifespan Overview The DGS-P PoE Gigabit Desktop switch provides a cost-effective way for SOHO and SMB to benefit from the Power over Ethernet (PoE) technology by allowing users to power up devices such as wireless access points, network cameras or IP phones directly from the network cables. The DGS-P is equipped with Gigabit ports for faster speeds, and integrates D-Link's Green Ethernet technology to save power when the switch is not in use. Its fanless design makes it completely silent so it is ideal for offices, libraries or meeting rooms. The first four ports of the DGS-P support the IEEE af PoE standard. Each of these four ports can supply up to 15.4 Watts, making it a very convenient solution for applications that are far away from power outlets, or when it is necessary to minimize the clutter of extra power supplies. The switch will automatically detect the power that a connected PoE device requires so no configuration is needed. A failsafe mechanism will cut off the power in case of an unexpected PoE overload, protecting both the switch and the connected device. Every time the DGS-P is powered up, it runs a micro diagnostics routine to check the integrity of the connected Ethernet cables. If a failure is detected, the switch will flag it by means of its front panel LEDs, making it easy for the user to troubleshoot wiring problems. Despite being an unmanaged, Plug and Play switch, the DGS-P is able to classify network traffic by assessing the existing p and DSCP fields in the Ethernet frames and IP packets respectively, and forward them out of its ports depending on their priority. This allows for a smooth integration of video, voice and data traffic without delays or loss of quality. The DGS-P is part of D-Link Green, D-Link's eco-friendly technology, providing energy savings, reduced power consumption, and a longer product lifespan without sacrificing operational performance or functionality. This switch implements the Green Ethernet technology, which can save a substantial amount of energy by detecting the connected cable lengths, adjusting the power accordingly; and the port status, putting them in low-power, stand-by mode when no network traffic is detected. Thanks to these power reductions, D-Link has been able to remove the fans in the DGS-P's design, making it completely silent and dramatically increasing its lifespan. Specifications Product Description D-Link DGS-P 8-Port PoE Gigabit Desktop Switch - switch - 8 ports - unmanaged - desktop Device Type Switch - 8 ports - unmanaged Enclosure Type Desktop Subtype Gigabit Ethernet Ports 4 x (PoE) + 4 x Power Over Ethernet (PoE) PoE MAC Address Table Size 4K entries Features Flow control, full duplex capability, auto-negotiation, auto-uplink (auto MDI/MDI-X), packet filtering, store and forward, Quality of Service (QoS), Jumbo Frames support, Green Ethernet, Cable Diagnostics Function Compliant Standards IEEE , IEEE u, IEEE ab, IEEE p, IEEE af, IEEE x Dimensions (WxDxH) 19 cm x 12 cm x 3.8 cm Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a vaild manufacturers warranty/guarantee. Manufacturer's Code: DGS-P/E D-Link

D-Link DGS-P 8-Port PoE | DGS-P/E Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery D-Link Product Code: DGS-P/E Availability: 68 in Stock Plug and Play operation Gigabit speed Fanless, silent operation to fit in any environment Safety function to prevent PoE overloads, protects both the switch and the connected PoE devices Cable diagnostics function to help troubleshoot wiring problems Green Ethernet technology, saves energy and increases the product's lifespan Overview The DGS-P PoE Gigabit Desktop switch provides a cost-effective way for SOHO and SMB to benefit from the Power over Ethernet (PoE) technology by allowing users to power up devices such as wireless access points, network cameras or IP phones directly from the network cables. The DGS-P is equipped with Gigabit ports for faster speeds, and integrates D-Link's Green Ethernet technology to save power when the switch is not in use. Its fanless design makes it completely silent so it is ideal for offices, libraries or meeting rooms. The first four ports of the DGS-P support the IEEE af PoE standard. Each of these four ports can supply up to 15.4 Watts, making it a very convenient solution for applications that are far away from power outlets, or when it is necessary to minimize the clutter of extra power supplies. The switch will automatically detect the power that a connected PoE device requires so no configuration is needed. A failsafe mechanism will cut off the power in case of an unexpected PoE overload, protecting both the switch and the connected device. Every time the DGS-P is powered up, it runs a micro diagnostics routine to check the integrity of the connected Ethernet cables. If a failure is detected, the switch will flag it by means of its front panel LEDs, making it easy for the user to troubleshoot wiring problems. Despite being an unmanaged, Plug and Play switch, the DGS-P is able to classify network traffic by assessing the existing p and DSCP fields in the Ethernet frames and IP packets respectively, and forward them out of its ports depending on their priority. This allows for a smooth integration of video, voice and data traffic without delays or loss of quality. The DGS-P is part of D-Link Green, D-Link's eco-friendly technology, providing energy savings, reduced power consumption, and a longer product lifespan without sacrificing operational performance or functionality. This switch implements the Green Ethernet technology, which can save a substantial amount of energy by detecting the connected cable lengths, adjusting the power accordingly; and the port status, putting them in low-power, stand-by mode when no network traffic is detected. Thanks to these power reductions, D-Link has been able to remove the fans in the DGS-P's design, making it completely silent and dramatically increasing its lifespan. Specifications Product Description D-Link DGS-P 8-Port PoE Gigabit Desktop Switch - switch - 8 ports - unmanaged - desktop Device Type Switch - 8 ports - unmanaged Enclosure Type Desktop Subtype Gigabit Ethernet Ports 4 x (PoE) + 4 x Power Over Ethernet (PoE) PoE MAC Address Table Size 4K entries Features Flow control, full duplex capability, auto-negotiation, auto-uplink (auto MDI/MDI-X), packet filtering, store and forward, Quality of Service (QoS), Jumbo Frames support, Green Ethernet, Cable Diagnostics Function Compliant Standards IEEE , IEEE u, IEEE ab, IEEE p, IEEE af, IEEE x Dimensions (WxDxH) 19 cm x 12 cm x 3.8 cm Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a vaild manufacturers warranty/guarantee. Manufacturer's Code: DGS-P/E D-Link

Description Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Description M-Link 8-Ports 10/100/1000Mbps PoE Unmanaged Network Switch TXE143 is a 10-Ports 10/100/1000Mbps Desktop PoE network switch that provides a seamless network connection. These PoE Ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs). In this situation, the electrical power is transmitted along with Data in one single Cable. Allowing you to expand your network where there are no power lines or outlets. Where you wish to fix devices such as APs, IP Cameras or IP Phones, etc. VLAN isolation to meet security monitoring requirements Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic. And ensure that the upstream channel is unobstructed. TXE143 is easy to install and use. It requires no configuration and installation. With desktop design, outstanding performance, and quality. The 10-Ports 100/100/1000Mbps Desktop PoE switch is a great selection for expanding your home or office network Features: Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3ab, IEEE802.3x,IEEE802.3az, IEEE802.1q Ethernet standards Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE Port, all power up to 120W VLAN isolation to meet security monitoring requirements Support 10 x10/100/1000Mbps Auto-negotiation RJ45 ports with 8 ports PoE function (port1-port8) Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode; LED indicators for monitoring Port Link / Activity; Internal Power Supply, exquisite design, suitable for Desktop use

M-Link 8-Ports 10/100/1000Mbps PoE Unmanaged Network Switch TXE143 is a 10-Ports 10/100/1000Mbps Desktop PoE network switch that provides a seamless network connection. These PoE Ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs). In this situation, the electrical power is transmitted along with Data in one single Cable. Allowing you to expand your network where there are no power lines or outlets. Where you wish to fix devices such as APs, IP Cameras or IP Phones, etc. VLAN isolation to meet security monitoring requirements Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic. And ensure that the upstream channel is unobstructed. TXE143 is easy to install and use. It requires no configuration and installation. With desktop design, outstanding performance, and quality. The 10-Ports 100/100/1000Mbps Desktop PoE switch is a great selection for expanding your home or office network Features: Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3ab, IEEE802.3x,IEEE802.3az, IEEE802.1q Ethernet standards Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE Port, all power up to 120W VLAN isolation to meet security monitoring requirements Support 10 x10/100/1000Mbps Auto-negotiation RJ45 ports with 8 ports PoE function (port1-port8) Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode; LED indicators for monitoring Port Link / Activity; Internal Power Supply, exquisite design, suitable for Desktop use

FS-S1004EP-FS20 is specialized unmanaged PoE switch designed for video surveillance and network project system. Provides 4 x 100Mbps Ethernet ports and 2 x 100Mbps uplink ports, supports VLAN function, can effectively prevent the whole system from a broadcast storm so that make the data transfer safer. PoE network switch can meet customers general demands.PoE network switch with PoE function, designed for high-definition network cameras￢ﾀﾙ internet access. Provides 4 100Mbps PoE Ethernet switches, complies with IEEE802.3AF/AT standards and also simplifies wiring, avoids the troublesome of installing power socket for powered devices. FEATURES Provide 4 x 100Mbps Ethernet ports and 2 x 100Mbps uplink ports Support end-span method complies with IEEE802.3AF/AT standards, can supply max 30W power which is possible to power high-power infrared cameras Compliant with IEEE802.3, IEEE802.3u, IEEE802.3AF/AT standards Support IEEE802.3x full-duplex flow control, support auto MDI/MDIX Support port-base Vlan, prevent from broadcast storm so that make data conversion more efficient and safe Restart function helps master IC reset wholly, easy for users to solve network failure without swapping power supply, easy to maintain system; Help to monitor pictures recover quickly Various LED display functions can real-timely display the device￢ﾀﾙs current working conditions, and help prompt facility and remove trouble easily Excellent lightning protection, lightning capacity up to 4K Easy to install and operate on walls

Description TP-Link TL-POE150S PoE Injector Adapter The TP-Link TL-POE150S PoE Injector Adapter fully complies with IEEE 802.3af standard and can work with all IEEE 802.3af PoE compliant PDs (Powered Devices) or PoE Receiver Adapters, such as TP-LINK’s TL-POE10R, or other equivalent product, to expand your network to where there are no power line or outlet, where you wish to fix device such as AP, IP Camera or IP Phone, etc.

LevelOne FEP-0811 - switch - 8 | FEP-0811 Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery LevelOne Product Code: FEP-0811 Availability: 9 in Stock Complies with IEEE 802.3af, 802.3, 802.3u and 802.3x 8 x PoE ports support 15.4 W power on each port to PoE powered device Each switching port supports 10/100 Mbps auto-negotiation Auto-MDI/MDI-X detection on each RJ-45 port 4K MAC address table, automatic source address learning and ageing 11-inch metal case with 19-inch rack mount holder Internal power supply Overview The LevelOne FEP-0811 is a high-performance 10/100 Mbps Ethernet PoE switch. All 8 of the PoE ports are powered up to 15.4 W. The total PoE power budget is 123.2 W. This switch automatically detects IEEE 802.3af compliant powered devices and provides power and data over a single cable. It's an ideal solution for office and home users to utilize a combination of PoE and non-PoE devices. Specifications Product Description LevelOne FEP-0811 - switch - 8 ports - rack-mountable Device Type Switch - 8 ports Enclosure Type Rack-mountable Subtype Fast Ethernet Ports 8 x 10/100 (PoE) Power Over Ethernet (PoE) PoE Performance Switching capacity: 1.6 Gbps MAC Address Table Size 4K entries Features Flow control, power over Ethernet (PoE), auto-uplink (auto MDI/MDI-X), store and forward, full duplex mode Compliant Standards IEEE 802.3, IEEE 802.3u, IEEE 802.3af, IEEE 802.3x Power AC 120/230 V (50/60 Hz) Dimensions (WxDxH) 1.85 cm x 28 cm x 4.4 cm Weight 1.6 kg Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a valid manufacturers warranty/guarantee. Manufacturer's Code: FEP-0811 LevelOne

Description M-Link 8 PORT 10/100 POE+2 PORT Switch 8PORT 10/100 POE+2PORT – TXE188 8-Ports 10/100Mbps PoE + 2-Ports 10/100Mbps Unmanaged Ethernet Switch Description TXE188 is a 10-port 10/100Mbps Desktop PoE Switch that provides the seamless network connection These PoE ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs) In this situation, the electrical power is transmitted along with data in one single Cable Allowing you to expand your network where there are no power lines or outlets here you wish to fix devices such as Aps IP Cameras or IP Phones, etc VLAN isolation to meet security monitoring requirements Support extension technology Data transmission and Power Supply up to 250m Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed. TXE188 is easy to install and use. It requires no configuration and installation With desktop design, outstanding performance and quality The 10-Port 10/100Mbps Desktop PoE switch is a great selection for expanding your home or office network Features Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3x,IEEE802.3az,IEEE802.1q Ethernet standards; Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE port, all power up to 117W VLAN isolation to meet security monitoring requirements Support 10 x10/100Mbps Auto-negotiation RJ45 ports with 8 port PoE function (POE1-8); Support extension technology, up to 250m transmission distance Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode and backpressure for Half-duplex Mode LED indicators for monitoring Port Link / Activity Internal power supply, exquisite design, suitable for desktop use b'/xc2/xa0'

M-Link 8 PORT 10/100 POE+2 PORT Switch 8PORT 10/100 POE+2PORT – TXE188 8-Ports 10/100Mbps PoE + 2-Ports 10/100Mbps Unmanaged Ethernet Switch Description TXE188 is a 10-port 10/100Mbps Desktop PoE Switch that provides the seamless network connection These PoE ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs) In this situation, the electrical power is transmitted along with data in one single Cable Allowing you to expand your network where there are no power lines or outlets here you wish to fix devices such as Aps IP Cameras or IP Phones, etc VLAN isolation to meet security monitoring requirements Support extension technology Data transmission and Power Supply up to 250m Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed. TXE188 is easy to install and use. It requires no configuration and installation With desktop design, outstanding performance and quality The 10-Port 10/100Mbps Desktop PoE switch is a great selection for expanding your home or office network Features Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3x,IEEE802.3az,IEEE802.1q Ethernet standards; Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE port, all power up to 117W VLAN isolation to meet security monitoring requirements Support 10 x10/100Mbps Auto-negotiation RJ45 ports with 8 port PoE function (POE1-8); Support extension technology, up to 250m transmission distance Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode and backpressure for Half-duplex Mode LED indicators for monitoring Port Link / Activity Internal power supply, exquisite design, suitable for desktop use b'/xc2/xa0'

READ SHIPPING PAGE. NO ORDERS WILL BE DISPATCHED UNLESS CORRECT SHIPPING IS PAID Ubiquiti EdgeRouter X - 5 Port Gigabit Router ER-X Sophisticated Routing Features. Advanced Security, Monitoring, & Management. High-Performance Gigabit Ports Ubiquiti Networks introduces the EdgeRouter™ X, part of the EdgeMAX® platform. The EdgeRouter X combines carrier class reliability with excellent price to performance value in an ultra compact form factor.  Versatile PoE Capability Powered by 24V passive PoE or a power adapter, the EdgeRouter™ X features a passive PoE passthrough option* to power an airMAX® device. Gigabit Connectivity The EdgeRouter™ X provides five independent, Gigabit RJ45 ports that are configurable for switching. Carrier-Class Reliability The EdgeRouter™ X delivers uptime performance equal to leading carrier or enterprise technology solutions. EdgeOS™ - Intuitive User Interface The EdgeRouter X provides a graphical user interface designed for convenient setup and control. Accessed via a network port and web browser, the user-friendly interface provides intuitive management with a virtual view of the ports, displaying physical connectivity, speed, and status. The Dashboard displays detailed statistics: IP information, MTU, transmit and receive speeds, and status for each physical and virtual interface. Configuration Methods Powered by a proprietary and intuitive graphical interface, EdgeOS™, EdgeRouter X can easily be configured for the routing, security, and management features required to efficiently run your network. For advanced network professionals, an integrated CLI is available for quick and direct access using familiar commands. Powerful Features EdgeOS is a sophisticated operating system with robust features, including: VLAN interfaces for network segmentation Static routes and support of routing protocols: OSPF, RIP, and BGP Firewall policies and NAT rules DHCP services Quality of Service (QoS) Network administration and monitoring tools Administrator and operator accounts Comprehensive IPv6 support Configuration by CLI The CLI provides quick and flexible configuration by command line and features the following: For power users, configuration and monitoring of all advanced features Direct access to standard Linux tools and shell commands CLI access through SSH, Telnet, and the graphical user interface Package Contents EdgeRouter X Power Adapter (12V, 0.5A) Quick Start Guide View all my items. Click Here     Internet transfer, Cash Deposit, Cash on Collection.  Payment to be made in 48 Hours. NO EXCEPTIONS  

Mikrotik RouterBoard Groove 2Hn Metal is completely waterproof, rugged, and super high powered RouterBOARD Metal is now available in 2.4Ghz. The MikroTik RouterBoard part number for this product is: Metal2SHPn. Fully sealed, industrial design metal case, powered by RouterBOARD and RouterOS. 1.6 WATT of output power - to reach the last mile, in severe conditions. It has a built-in N-male connector, and pole attachment points, so you can attach it directly to an antenna, or use a standard antenna cable. LED signal indicators simplifies installation and alignment. Package contains Metal-2SHPn, mounting loops, PoE injector, power adapter. Specifications: CPU speed: 400MHz. TX power: 32dBm. Current Monitor: no. CPU: AR. Max Power consumption: 11.5W. RAM: 64MB. Architecture: MIPS-BE. LAN ports: 1. Gigabit: No. MiniPCI: 0. Integrated Wireless: Yes. Wireless standards: b/g/n. Power Jack: No. af support: No. PoE: 8-30V DC. Voltage Monitor: yes. PCB temperature monitor: yes. CPU temperature monitor: No. Operating System: RouterOS. Temperature range: -30C to +70C. RouterOS License: Level4. Dimensions: 177 x 44 x 44mm. Weight: 193g

Mikrotik Routerboard Rack Mount, 5 LAN Ports, 5 Gigabit LAN ports with PSU is a low cost, multi-port device series. Designed for indoor use, and powered by RouterOS, a fully featured routing operating system. Dynamic routing, hotspot, firewall, MPLS, VPN, advanced quality of service, load balancing and bonding, real-time configuration and monitoring - just a few of the vast number of features supported by RouterOS. The MikroTik RouterBoard part number for this product is: RBiL-RM. It includes a power injector on Ethernet port 10 - it can power other PoE capable devices with the same voltage as applied to the unit. Less power adapters and cables to worry about! Maximum load on the port is 500mA. It's powered by the new Atheros 600MHz 74K MIPS network processor, has 64MB of RAM and a Level4 RouterOS license, as well as five Gigabit Ethernet ports and five Fast Ethernet ports. RouterBOARD iRM comes with 1U rack mount enclosure and power supply. Specifications: CPU speed: 600MHz. Architecture: MIPS-BE. RAM: 64MB. LAN ports: 5. Gigabit: 5. MiniPCI: 0. Integrated Wireless: No. PoE: 8-30V. Voltage Monitor: No. CPU temperature monitor: No. PCB temperature monitor: No. Temperature range: -35C to +65C. RouterOS License: L4. Current Monitor: No. CPU: Atheros AR. Max Power consumption: 6W

Features: In wall design, match with the cassette with size of 86mm, easy to complete the hotel WiFi cover. Compliant with IEEE n/g/n standard, 300Mbps in data rate, more faster in download, more freely in internet surf. Support af 48V PoE, can be powered by any powered by any af Power over Ethernet equipment, easy in setting and complete the full wifi coverage. Powerful Frequency band from 2.4GHz to GHz. Equipped with 2 RJ45 ports, one on the front allowing wired access for guests and one on the rear for network service and power provision. It also has an RJ11 pass through port on the front with screw terminals on the rear. The Rj11 port can be used for a telephone. Support Q VLAN manage and Access Controller System (ACS), the IT staff can sets up different IP addresses, ESSID and manages each room’s AP at the same time. Muti SSID: PW300AP support 4 SSID, each SSID can be named and assigned to different users, then internet data is isolated. Specifications: Hardware MCU Chipset MTN RF 2T2R Memory 32MB DDR RAM (can be extended to 64 MB) Flash 4MB (can be extended to 8 MB) Interface Mbps/ 10Mbps auto-negotiation ethernet LAN / WAN ports 1 * RJ11 port Power 48V / 0.5A(Standard af POE) Antenna Internal 2dBi Product size mm / in Product weight 102g / 3.6oz Wireless Wireless standards IEEE n, IEEE g, IEEE b Speed 11b: up to 11Mbps 11g: up to 54Mbps 11n: up to 300Mbps Frequency GHz Security -bit WEP, WPA / WPA2,WPA-PSK / WPA2-PSK Channel 1 ~ 13 Out Power n: 15dBm for OFDM mode g: 17dBm for OFDM mode b: 20dBm for CCK mode Modulation OFDM = BPSK, QPSK, 16-QAM, 64-QAM DSSS = DBPSK, DQPSK, CCK Sensitivity 270M: -68dBm@10% PER 130M: -68dBm@10% PER 108M: -68dBm@10% PER 54M: -68dBm@10% PER 11M: -85dBm@8% PER 6M: -88dBm@10% PER Software Woke mode Gateway / AP / Repeater Wireless function Auto-Channel selection Distance Control (x Ack timeout) Multiple SSID (4 SSID) BSSID Security WEP Encryption- bit WPA/WPA2 Personal (WPA-PSK using TKIP or AES) WPA/WPA2 Enterprise (WPA-EAP using TKIP) Hide SSID DHCP DHCP Server, DHCP Client Network Port Mapping, DDNS, UPNP Firewall IP Address / Port / MAC / URL Filter / ANI-DoS Management Firmware upgrade and backup, factory reset, restart, WEB management OS Support Windows 7/Vista/XP/, Mac OS?, Linux or Android OS Environment Operating temperature °F~104°F) Storage temperature -°F~158°F) Operating humidity %, non-condensing Storage humidity 5% ~ 95%, non-condensing Package Package size mm / in Package weight 176g / 6.2oz Package List: 1 * In Wall AP 1 * Setting Accessory 1 * User Manual (English)

Mikrotik RouterBoard Groove 5SHPn Metal is rugged, completely waterproof, and high-powered. It has a built-in N-male connector and pole attachment points, so you can directly attach it to an antenna or use a standard antenna cable. LED signal indicators make it easy to install and align. The MikroTik RouterBoard part number for this product is: Metal 5SHPn. The RB-METAL5 has a fully sealed, industrial design metal case, powered by RouterBOARD and RouterOS. With 1.3 WATT of power output, it assists the user in reaching the last mile in almost any conditions. Package contains Metal-5SHPn, mounting loops, PoE injector, and power adapter. Specifications: CPU: Atheros ARMHz network processor. Memory: 64MB DDR SDRAM onboard memory. Ethernet: One Mbit/s Fast Ethernet port with Auto-MDI/X. Ethernet: L2MTU up to . Wireless: Built-in 5GHz a/n 1x1 MIMO, N-male connector. Wireless: Up to 1.3W output power. Extras: Reset switch, Beeper, Voltage monitor, Temperature monitor. LEDs: 5 Wireless signal LEDs, ethernet activity LED (configurable). Power options: Passive 8-30V PoE only. 16KV ESD protection on RF port. Consumption: Up to ~0,5A at 24V (11.5W). TX power: 31dBm. Architecture: MIPS-BE. LAN ports: 1. Gigabit: 0. MiniPCI: af support: No. Operating System: OS v5, Level4 licence (station, point-to-point or AP modes). Operating Temperature: -30ºC to +70ºC. Package contains: Metal 5SHPn unit, mounting loops, PoE injector, 24V power adapter. Dimensions (mm): 177x44x44. Weight: 193g. * It must be mounted with ethernet pointing down.

Mikrotik RouterBoard Groove 52Hn (RouterOS L3) is a small, outdoor, fully featured wireless RouterBOARD powered by RouterOS. Weatherproof, durable and ready to use. It has one Ethernet port with PoE support and a built in wireless radio. It has software selectable 2 or 5GHz wireless mode, and 500mW output power. The MikroTik RouterBoard part number for this product is: Groove 52HPn. With the Nv2 TDMA technology, up to 125Mbit aggregate throughput is possible. It has a built-in N-male connector, and pole attachment points, for easy attachment, directly to an antenna, or you can use a standard antenna cable. LED signal indicators assists with installation and alignment. Box contains: Groove unit, mounting loops, PoE injector, power adapter. Specifications: CPU speed: 600MHz. CPU cores: 1. RAM: 64MB. LAN ports: 1. Gigabit: no. MiniPCI: 0. Integrated Wireless: Yes. Wireless standards: a/b/g/n. PoE: 9-30V. Voltage Monitor: No. PCB temperature monitor: No. CPU temperature monitor: No. Operating System: RouterOS. Temperature range: -30C to +70C. RouterOS License: L3. Current Monitor: No. TX power: 27dBm. CPU: AR. Max Power consumption: Up to 0.19A at 24V (4.56W). Dimensions: 177 x 44 x 44mm, 193g

MikroTik RouterBoard 2011UIAS (Rack-mount version) The RB2011 is a low cost multi port device series. Designed for indoor use, and available in many different cases, with a multitude of options. The RB2011 is powered by RouterOS, a fully featured routing operating system which has been continuously improved for fifteen years. Dynamic routing, hotspot, firewall, MPLS, VPN, advanced quality of service, load balancing and bonding, real-time configuration and monitoring - just a few of the vast number of features supported by RouterOS. RouterBOARD 2011UiAS-RM, in comparison with RB2011L series, not only has five Gigabit LAN ports and five Fast Ethernet LAN ports, but also has RJ45 serial port, microUSB port and more RAM (128MB instead of 64MB). Also, it has RouterOS L5 license (instead of L4) and nice touchscreen LCD for configuration. SFP cage is also present (SFP module not included!) There is PoE output function for port #10 - it can power other PoE capable devices with the same voltage as applied to the unit. Maximum load on the port is 500mA. The RouterBOARD 2011UiAS-RM comes with 1U rackmount enclosure, LCD panel and power supply.

This RB-2011ILSIN by MikroTik RouterBoard has a SFP cage for gigabit SFP transceivers and is ideal for FTTH (Fiber To The Home) implementations. Note that SFP transceiver is NOT included. The RB-2011ILSIN supports any 1.25G SFP transceiver that is within the SFF Committee specifications for SFP Transceivers. It does not have hardware support for PON (Passive Optical Network). Tested and recommended to use with MikroTik SFP modules: S-85DLC05D, S-31DLC20D and S-35/53LC20D (not included). It is powered by an Atheros next generation 600MHz 74K MIPS network processor and has 64MB of RAM and a Level4 RouterOS license. There is PoE output function for port number 10 - it can power other PoE capable devices with the same voltage as applied to the unit. Maximum load on the port is 500mA. RouterBOARD 2011iLS-IN comes with desktop enclosure and power supply.

This RB-GROOVE52 by MikroTik RouterBoard is a small, outdoor, fully featured wireless RouterBOARD powered by RouterOS. Weatherproof, durable and ready to use. It has one 10/100 Ethernet port with PoE support and a built in wireless radio. It has software selectable 2 or 5GHz wireless mode, and 500mW output power. With the Nv2 TDMA technology, up to 125Mbit aggregate throughput is possible. It has a built-in N-male connector, and pole attachment points, for easy attachment, directly to an antenna, or you can use a standard antenna cable. LED signal indicators assists with installation and alignment. Box contains: Groove unit, mounting loops, PoE injector, power adapter

Description TENDA CEILING AP, 23DBM 867MBPS CEN MAN b'/xc2/xa0' Tenda i24 AC1200 Wave 2 Dual Band PoE Access Point i24 is a gigabit dual-band ceiling access point that is compliant with IEEE 802.11ac Wave 2 And offers a concurrent data rate of up to 1167 Mbps. Powered by MU-MIMO technology, letting you enjoy a better experience. And the built-in Omni-directional antennas broaden the wireless coverage of a single AP. In addition, you are allowed to adjust its transmit power as required using the web UI, and use an IEEE 802.3 At-compliant PoE sourcing equipment to power on it, achieving a long-distance power supply without tampering with your existing grid network. You are also allowed to use Tenda access controllers (AC) to configure and manage multiple i24 in a centralized manner. Products Features Gigabit internet connections for ultra-fast experience Up to 1317 Mbps dual-band data rate, the Tenda 124’s 1000 Mbps Ethernet port lets you enjoy ultra-fast internet connections. Dual-Band to reduce network crowding Connect to the network using either 2.4GHz or 5GHz to reduce network crowing and increase browsing speeds. Resource allocation Featuring air interface scheduling, the Tenda i24 AC1200 evenly allocates air interface resources. Thus improving your wireless network speed as a whole by preventing clients with low data rates from consuming too much of the network’s resources. You can also customize the RSSI threshold value so that clients that do not reach the RSSI threshold can be disconnected. Multiple interference-mitigation The Tenda i24 AC1200 automatically chooses the best channel and adjusts the transmit power to a reasonable value. Significantly optimizing wireless signals by mitigating co-channel interference and electromagnetic interference (EMI).