Poe injector

Barely used for 2 Voip Phones. The CNP-POEI is a Power over Ethernet Injector which can Inject power into a non-powered eternet cable and deliver Electrical Current to PoE compliant devices such as APs, IP Cameras or IP Phones, where there are no power lines or outlets available. It fully complies with IEEE af standard, and can work with all IEEE af PoE compliant PDs (Powered Devices) or PoE reciever adapters, such as Canyon’s CNP-POES. The instalation is very simple (Plug-and-play), and there is no configuration or software required. IEEE af compliant PoE Injector Delivers power up to 100 meters Auto-determine the necessary power requirements Plug-and-Play, no configuration required External power adapter supply  

The CNP-POEI is a Power over Ethernet Injector which can Inject power into a non-powered eternet cable and deliver Electrical Current to PoE compliant devices such as APs, IP Cameras or IP Phones, where there are no power lines or outlets available. It fully complies with IEEE af standard, and can work with all IEEE af PoE compliant PDs (Powered Devices) or PoE reciever adapters, such as Canyon’s CNP-POES. The instalation is very simple (Plug-and-play), and there is no configuration or software required. IEEE af compliant PoE Injector Delivers power up to 100 meters Auto-determine the necessary power requirements Plug-and-Play, no configuration required External power adapter supply  

PoE injector by Tenda enables synchronous delivery of data and power via a single Ethernet cable (Cat.5 or better). The output power per port is up to 15W, which can serve as an outlet for a PoE device (powering via RJ45 port). You can connect the PoE15F to an IEEE 802.3af compliant device, such as a wireless AP, IP camera, IP phone, etc. Ideal for reducing installation cost and improving network performance.

  POE-PA2 Passive PoE Injector, Splitter 12v, Splitter 5v, Up to 50 Volt     The POE-PA2 is a passive PoE injector / splitter system that supports 5v, 12v, and up to 50 volt power over Ethernet transmission over CAT-5 cable. This product is used with non-PoE IP cameras and network devices. The POE-PA2 set contains two pieces: PoE injector and PoE splitter. The PoE injector has an RJ45 male plug, a male 2.1mm DC power jack, and an RJ45 female plug. The male RJ45 connects to a network router or switch. The power jack connects to the power supply that was included with your non-PoE device (such as an IP camera). A CAT5 cable connects to the female RJ45 plug and connects on the other end of the cable run to the female RJ45 on the splitter. The splitter also has an RJ45 male plug which connects to the IP camera or other non-PoE network device. The 2.1mm female power plug connects to the power input of the IP camera (typically 12v or 5v DC). 

Description Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Planet POE--Port af PoE Injector is a 4-Port IEEE af Power over Ethernet injector hub. Equipped with Base-TX Fast Ethernet ports, the POE-400 supports full 48VDC power for any remote IEEE af powered devices, such as Wireless LAN Access Points, IP phones and LAN Cameras. Supporting power supply of 70 watts, the POE-400 provides sufficient power to the 4 remote devices. There are 8 RJ-45 STP ports on the POE-400. Half of the ports on the right panel function as "Data" and the other half on the left panel function as "Data and Power". Each of the "Data and Power" ports is an injector that inserts DC Voltage into the CAT 5 cable allowing the cable between the Injector and Splitter to transfer data and power simultaneously. Specifications: Ethernet Connector: 8-Port RJ-45 STP with 4-Port "Data" & 4-Port "Data & Power", Ethernet Data Rate: Mbps (vary on Ethernet device attached), Input Voltage: DC 48V, 1.5A, Number of Devices that can be powered: 4, Ethernet Cable: TIA/EIA-568, Category 5/5e cable, LED Indicator: 1 x power, 4 x PoE ready / in-use, Operating Temperature: 0ºC ~ 50ºC, Storage Temperature: -20ºC ~ 70ºC, Humidity: 5% ~ 90% RH, Emission: FCC Class B, CE mark, Standard Compliance: iEEE Ethernet; IEEE u Fast Ethernet; IEEE af Power over Ethernet, Dimensions: HxWxD: 26 x 70 x 97 mm, Weight: 220g

Description 4-Port 10/100Mbps Passive PoE Injector The 4-port passive PoE injector allows you to power four devices from a single appropriate power supply, eliminating multiple power adapters and saving you valuable space in your installation. This PoE injector strip has a 2.1×5.5mm Female DC Jack for power input. Outputs the same voltage, and up to 650mA per port (max).

Description 6 Port Gigabit Passive PoE Injector This 6-port passive PoE injector allows you to power six devices from a single power supply. Gigabit Ethernet connectivity means no bottlenecks and maximum throughput. Simply connect your Ethernet cables to the LAN ports and your PoE devices to the POE ports.

Description Tenda 10/100Mbps POE Injector Tenda 10/100Mbps POE Injector PoE15F can realize the synchronous transmission of network data and power through an Ethernet cable (Cat.5 or better). The output power of each port is as high as 15W, which can be exported as PoE equipment (via RJ45 port). You can connect to ieee802.3af’s PD, such as wireless AP, IP camera, IP phone, etc. In a sense, reducing installation costs and improving network performance is a good choice. Features: Delivers power and data through one Ethernet cable for easy network extension Compatible with IEEE 802.3af compliant powered devices PoE Port Delivers power up to 100 meters Plug and Play, no configuration required Power Over Ethernet One PoE port to power connected devices for flexible network deployment IEEE 802.3af compliant Compatible with IEEE 802.3af compliant powered devices Extend Power Supply Distance of power transmission via Ethernet cable is up to 100 meters Plug and Play Hassle-free setup, no configuration required Specifications: Network standards IEEE802.3、IEEE802.3u LED Indicator Link/Act, PoE Status Interfaces 1*10/100 Base-TX Ethernet ports(Data/PoE) 1*10/100 Base-TX Ethernet ports(Data) Transmission media Recommended: CAT5/5e UTP or better Dimension 84.5mm*44mm*29.8 mm Level of protection ESD: Air discharge: ±10kV Contact discharge: ±8kV Forwarding mode Store-and-forward Transmission Rate 100Mbps PoE budget Single port: AF: 15.4W Whole device: 15W Power consumption 15W Input voltage 100－240V AC 50/60Hz 48V/0.3A DC（Power Adapter Output） Mounting Desktop mounting: support Environment Operating Temperature: 0℃~45℃ Storage Temperature: -40℃~70℃ Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Certification FCC、CE、RoHS b'/xc2/xa0' Why not browse our wide variety of Tenda Products HERE

Tenda 10/100Mbps POE Injector Tenda 10/100Mbps POE Injector PoE15F can realize the synchronous transmission of network data and power through an Ethernet cable (Cat.5 or better). The output power of each port is as high as 15W, which can be exported as PoE equipment (via RJ45 port). You can connect to ieee802.3af’s PD, such as wireless AP, IP camera, IP phone, etc. In a sense, reducing installation costs and improving network performance is a good choice. Features: Delivers power and data through one Ethernet cable for easy network extension Compatible with IEEE 802.3af compliant powered devices PoE Port Delivers power up to 100 meters Plug and Play, no configuration required Power Over Ethernet One PoE port to power connected devices for flexible network deployment IEEE 802.3af compliant Compatible with IEEE 802.3af compliant powered devices Extend Power Supply Distance of power transmission via Ethernet cable is up to 100 meters Plug and Play Hassle-free setup, no configuration required Specifications: Network standards IEEE802.3、IEEE802.3u LED Indicator Link/Act, PoE Status Interfaces 1*10/100 Base-TX Ethernet ports(Data/PoE) 1*10/100 Base-TX Ethernet ports(Data) Transmission media Recommended: CAT5/5e UTP or better Dimension 84.5mm*44mm*29.8 mm Level of protection ESD: Air discharge: ±10kV Contact discharge: ±8kV Forwarding mode Store-and-forward Transmission Rate 100Mbps PoE budget Single port: AF: 15.4W Whole device: 15W Power consumption 15W Input voltage 100－240V AC 50/60Hz 48V/0.3A DC（Power Adapter Output） Mounting Desktop mounting: support Environment Operating Temperature: 0℃~45℃ Storage Temperature: -40℃~70℃ Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Certification FCC、CE、RoHS b'/xc2/xa0' Why not browse our wide variety of Tenda Products HERE

Description TP-Link TL-POE150S PoE Injector Adapter The TP-Link TL-POE150S PoE Injector Adapter fully complies with IEEE 802.3af standard and can work with all IEEE 802.3af PoE compliant PDs (Powered Devices) or PoE Receiver Adapters, such as TP-LINK’s TL-POE10R, or other equivalent product, to expand your network to where there are no power line or outlet, where you wish to fix device such as AP, IP Camera or IP Phone, etc.

IEEE ab Gigabit and af PoE compliant Gigabit Power over Ethernet (PoE) Injector delivers a PoE signal for distances of up to 100 meters (328 ft.) 1 x Mbps Auto-MDIX Data In port 1 x Mbps PoE Auto-MDIX Data Out port Power port Power LED indicator Supplies power up to 15.4 Watts Easily install a PoE device where a power outlet is not available Reduce installation and network equipment costs Safeguards network devices with short circuit protection Plug and Play in remote location Light weight and compact size Wall mounting points

Ubiquiti PoE Injector 15V SA Version was designed for Station/CPE devices and features earth grounding/ESD protection and power LED. Specifications: Output Voltage: 15VDC @ 0.8A, Input Voltage: VAC @ Hz, Input Current: 0.3A @ 120VAC, 0.2A @230VAC, Inrush Current:

Planet Single Port 10/100/1000Mbps Ultra POE Injector (60 Watts) -w/external power adapter

Description 24 Port Gigabit Passive PoE Injector More Products View More Products

Buy Tenda 802.3at Gigabit PoE Injector | POE30-GAT for R508.88

Buy TP-LINK PoE Injector Adapter, IEEE 802.3af Compliant | TL-POE150S for R383.00

Buy Gigabit Power over Ethernet (PoE) Injector. 48V, Passive, 30 watt. for R460.46

Buy Single Port Fast Ethernet Passive PoE Injector for R1,225.00

Buy MikroTik GPEN Wall Mount Passive PoE Injector | GPEN11 for R210.00

Buy Passive PoE Injector and Splitter Set - Locally Sourced for R39.00

Hikvision IP Camera Code: Ds-2CD2512F-I with POE injector - Excellent condition Market value new: R2300.00 Delivery not included

Ubiquiti UniFi AP wireless panel (ex POE injector) - Excellent condition Market value new: R1550.00 Delivery not included

IN STOCK at supplier. If ordered before 12PM: DELIVERED next day (main centres) or 2-3 days (regional areas or large items) COLLECTION from Geewiz available Same Day (approx 4pm) POE-GIG, MikroTik Gigabit PoE adapter is designed to power any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an Ethernet cable to connect the injector to the RouterBOARD device.  The POE-GIG reduces the number of wires that lead up the tower. Power over pins 4 and 5 is used to power and communicate with 10/100/1000 Mbps devices. It can be used with any Gigabit RouterBOARD that supports 9-48V PoE.   SPECIFICATIONS - PoE: Passive PoE (non 802.3af)  - Input Voltage: 9-48V DC (Accepts up to 56V) - Output Voltage: any - Power: 4,5 Cable Pins - 9-48V; 7,8 Pins -Return  - Max. Current: 2A  - Ethernet Cable Length: Up to 60m  - Ethernet Speed: 10/100/1000 Mbps Please note that this item requires a 9-48V DC plug to function.

IN STOCK at supplier. If ordered before 12PM: DELIVERED next day (main centres) or 2-3 days (regional areas or large items) COLLECTION from Geewiz available Same Day (approx 4pm) Power Supply: 15.4W (Max. 48VDC) Expands network to areas with no power lines or outlets Ideal for use with access points and IP cameras Delivers power up to 100 meters (328 feet) Two Gigabit Ethernet ports for lightning-fast wired speeds Auto-detects the required power supply Plug and Play, no configuration required

Description M-Link 4 PORT 10/100 POE + 1 LAN Switch 4 PORT 10/100 POE + 1 LAN – TXE104 b'/xc2/xa0' 5 PORT 10/100 POE – TXE104 Hardware Specifications Network Connector: 5-port RJ45 for 10/100BASE-TX, auto MDI/MDIX PoE Inject Port: 4-port with 802.3af/at PoE injector function (Port 1 to Port 4) LED Display: System Power (Green) Per PoE port: PoE (Red/Blue, Port 1 to Port 4) LNK/ACT (Green, Port 1 to Port 5) DIP Switch: Standard mode for 100M Extend mode for 250m (Based on the cable category) Switch Architecture: Store and Forward switch architecture MAC Address Table: 1K MAC address table with auto learning function EST Protection: 4KV Switch Fabric: 1Gbps Switch Throughput: 0.74Mpps @64bytes Maximum Packet Size: 1536bytes b'/xc2/xa0'

M-Link 4 PORT 10/100 POE + 1 LAN Switch 4 PORT 10/100 POE + 1 LAN – TXE104 b'/xc2/xa0' 5 PORT 10/100 POE – TXE104 Hardware Specifications Network Connector: 5-port RJ45 for 10/100BASE-TX, auto MDI/MDIX PoE Inject Port: 4-port with 802.3af/at PoE injector function (Port 1 to Port 4) LED Display: System Power (Green) Per PoE port: PoE (Red/Blue, Port 1 to Port 4) LNK/ACT (Green, Port 1 to Port 5) DIP Switch: Standard mode for 100M Extend mode for 250m (Based on the cable category) Switch Architecture: Store and Forward switch architecture MAC Address Table: 1K MAC address table with auto learning function EST Protection: 4KV Switch Fabric: 1Gbps Switch Throughput: 0.74Mpps @64bytes Maximum Packet Size: 1536bytes b'/xc2/xa0'

Intellinet 12 Port Passive PoE Patch Panel - 24 Port Patch Panel with 12 port RJ45 Data In and 12 port RJ45 Data and Power Out, Retail Box, 2 year Limited Warranty. Product Overview: Do you need a cost effective solution to upgrade your Network with Power over Ethernet? Then the 720342 from Intellinet is your ideal solution. Intellinet is renowned for their PoE products and this is one of our latest additions. Highlights: • Passive Power over Ethernet Delivered on 12 Ports • 1U height • 19" Rack mountable • Simple Installation • Cost Effective Power over Ethernet Upgrade for your network • CAT5e Compatible Specifications: • Product Code: 720342 • Description: Intellinet 12 Port Passive PoE Patch Panel • 24 Port 1U 19" Patch Panel • 12 port RJ45 Data In • 12 port RJ45 Data and Power Out • 120 watts of usable power • Up to 30 watts per port • 12 PoE Injector Ports • Metal construction • Black

Buy RADWIN 2000/5000 Indoor DC-PoE Injector DC-DC Step-up Transformer 10VDC-60VDC input 48VDC PoE Out for R2,331.49