Usb ttl

USB To RS232 TTL UART PL2303HX Auto Converter USB to serial RS232 USB to 232 Converter Adapter PL2303HX MAX232 For Win7 or Linux Built-in TTL COM PC-PL2303HX Chip. Standard USB type A male and TTL 4 pin connector Simple and Easy way to give USB support to your designs Available for Linux, Mac, WinCE and Windows (XP, 2003), Vista Win 7 Black cable-----GND Green cable-----TXD White cable-----RXD Red cable -------VCC ​ Please Note: Locally stocked, Available for immediate shipping!

Description USB to I2C converter This USB2.0 Full Speed IC offers a compact bridge to I2C devices. The device is an I2C slave, capable of operating up to 3.4MBit/s, with low power consumption (8mA). This converter is based on the FT200XD chipset and includes the complete FT-X series feature set and enables USB to be added into a system design quickly and easily over an I2C interface. Quick Spec Single chip USB to I2C interface Up to 3.4MHz, high speed mode, I2C supported Fully integrated 2048 byte multi-time-programmable(MTP) memory storing device descriptors and CBUS I/O configuration Fully integrated clock generation with no external crystal required 512 byte receive buffer and 512 byte transmit Integrated +3.3V level converter for USB I/O True 3.3VCMOS drive output and TTL input, Operates down to 1V8with external pull-ups, tolerant of 5V input Configurable I/O pin output drive strength, 4mA(min) and 16mA(max) Integrated power-on-reset circuit Fully integrated AVCC supply filtering - no external filtering required +5V Single Supply Operation Internal 3V3/1V8 LDO regulators Resources FT200XD Datasheet VCP Drivers Shipping List 1 X Usb to I2C converter More Products View More Products

Description USB to RS485 - 3 Pin Running MODBUS/RTU over an RS485 network is pretty cool, in an old-school way. The technique was invented decades ago, and allowed you to connect to a few dozen MODBUS devices over simple twisted pair copper wire, over a thousand feet distance or more. It's such a successful technique that it has not been supplanted by new modern communication technologies like TCP/IP. Unfortunately most modern computers do not have RS-485 interfaces. Fortunately there are many USB-RS485 adapters available. RS485 to TTL Module is for long range, high data rate error prone differential communication. Digital communications networks implementing the EIA-485 standard can be used effectively over long distances and in electrically noisy environments. Multiple receivers may be connected to such a network in a linear, multi-drop configuration. These characteristics make such networks useful in industrial environments and similar applications. Quick Spec Standard: USB2.0 standard, backward compatible, in line with the standard RS485 Direction control: the use of automatic data flow control, auto distinguish and control data transfer direction Baud Rate: 300-9216000bps, automatically detecting the serial signal data rate Load capacity: support multipoint, each converter allows RS485 interface device to connect 32 Interface Protection: TVS tube protection, USB self-recovery protection Self-powered from USB Using virtual serial COM port Support Windows98 / ME / 2000 / XP / WIN7 / Vista / Linux / Mac Dimensions: 76 x 18.5 x 16mm Resources Datasheet Shipping List 1 X USB to RS485 - 3 Pin More Products View More Products

Description: Multifunction USB converter board fully supports Win8, Win7, WinXp,WinCE, Linux, 32-bit, 64-bit systems it! The history of the most powerful USB serial debugging tools, set USB to serial (TTL), to 232, turn 485, TTL, 232,485 conversion six practical function in a professional debugging tools, and the other supports 3.3V, 5V Oh the power output. Module ingenious design, making the board at the same time put the heat shrink tubing protection, without affecting the operation of the module. Module easy to operate, simple and can be used for single-chip program download, serial communications, 485, etc., are carried out pro microcontroller development essential artifact! ! Module Features: Module size: A compact design, the module is only 3.5 * 1.8CM ultra-small size, even if the design is very compact laptop plugged module does not affect the other USB port to insert other devices. Power Output: Supports 5V / 500mA, 3.3V / 100mA power output, you can easily give 3.3V or 5V power microcontroller download program. Module Protection: onboard 500mA self-recovery fuse, always protect your computer from a large current module and harm; supporting transparent shrink tube to prevent static electricity or electrical conductor hands of the module short circuit, causing damage to the module (put Heat Shrink Tubing will not affect the operation of your module oh). Operation: to achieve mutual conversion USB, TTL, 232,485 physical switch function switch, please read the specific operation. Indicator: connection, receive, send indicator lets you know whether the real-time module is connected to the computer or on the send and receive data. Communication quality: clever circuit design, PCB layout professional, making module communication efficient, stable, communication baud rate can reach up to 2Mbps. PCB Quality: Module chips used are industrial grade chips, modules for mass production, professional SMT chip, anti-static packaging after rigorous testing. Module interface: module left 3.3V, 5V, GND power supply interface, TTL level serial TXD, RXD, serial 232, 232T, 232R interface, 485 A, B interface, and DTR, RTS interface, easy DSP430 and other microcontrollers the program downloads. Package included: 3 x 6 In 1 CP2102 USB To TTL 485 232 Converter Module

Description: Multifunction USB converter board fully supports Win8, Win7, WinXp,WinCE, Linux, 32-bit, 64-bit systems it! The history of the most powerful USB serial debugging tools, set USB to serial (TTL), to 232, turn 485, TTL, 232,485 conversion six practical function in a professional debugging tools, and the other supports 3.3V, 5V Oh the power output. Module ingenious design, making the board at the same time put the heat shrink tubing protection, without affecting the operation of the module. Module easy to operate, simple and can be used for single-chip program download, serial communications, 485, etc., are carried out pro microcontroller development essential artifact! !   Module Features:   Module size: A compact design, the module is only 3.5 * 1.8CM ultra-small size, even if the design is very compact laptop plugged module does not affect the other USB port to insert other devices. Power Output: Supports 5V / 500mA, 3.3V / 100mA power output, you can easily give 3.3V or 5V power microcontroller download program. Module Protection: onboard 500mA self-recovery fuse, always protect your computer from a large current module and harm; supporting transparent shrink tube to prevent static electricity or electrical conductor hands of the module short circuit, causing damage to the module (put Heat Shrink Tubing will not affect the operation of your module oh). Operation: to achieve mutual conversion USB, TTL, 232,485 physical switch function switch, please read the specific operation. Indicator: connection, receive, send indicator lets you know whether the real-time module is connected to the computer or on the send and receive data. Communication quality: clever circuit design, PCB layout professional, making module communication efficient, stable, communication baud rate can reach up to 2Mbps. PCB Quality: Module chips used are industrial grade chips, modules for mass production, professional SMT chip, anti-static packaging after rigorous testing. Module interface: module left 3.3V, 5V, GND power supply interface, TTL level serial TXD, RXD, serial 232, 232T, 232R interface, 485 A, B interface, and DTR, RTS interface, easy DSP430 and other microcontrollers the program downloads. Package included: 5 x 6 In 1 CP2102 USB To TTL 485 232 Converter Module

Description: Multifunction USB converter board fully supports Win8, Win7, WinXp,WinCE, Linux, 32-bit, 64-bit systems it! The history of the most powerful USB serial debugging tools, set USB to serial (TTL), to 232, turn 485, TTL, 232,485 conversion six practical function in a professional debugging tools, and the other supports 3.3V, 5V Oh the power output. Module ingenious design, making the board at the same time put the heat shrink tubing protection, without affecting the operation of the module. Module easy to operate, simple and can be used for single-chip program download, serial communications, 485, etc., are carried out pro microcontroller development essential artifact! ! Module Features: Module size: A compact design, the module is only 3.5 * 1.8CM ultra-small size, even if the design is very compact laptop plugged module does not affect the other USB port to insert other devices. Power Output: Supports 5V / 500mA, 3.3V / 100mA power output, you can easily give 3.3V or 5V power microcontroller download program. Module Protection: onboard 500mA self-recovery fuse, always protect your computer from a large current module and harm; supporting transparent shrink tube to prevent static electricity or electrical conductor hands of the module short circuit, causing damage to the module (put Heat Shrink Tubing will not affect the operation of your module oh). Operation: to achieve mutual conversion USB, TTL, 232,485 physical switch function switch, please read the specific operation. Indicator: connection, receive, send indicator lets you know whether the real-time module is connected to the computer or on the send and receive data. Communication quality: clever circuit design, PCB layout professional, making module communication efficient, stable, communication baud rate can reach up to 2Mbps. PCB Quality: Module chips used are industrial grade chips, modules for mass production, professional SMT chip, anti-static packaging after rigorous testing. Module interface: module left 3.3V, 5V, GND power supply interface, TTL level serial TXD, RXD, serial 232, 232T, 232R interface, 485 A, B interface, and DTR, RTS interface, easy DSP430 and other microcontrollers the program downloads. Package included: 1 x 6 In 1 CP2102 USB To TTL 485 232 Converter Module

Feature: Size: 6.5 x 1.4cm Support Win10, Win8, Win7, VISTA, WinXp, Win2K, 32-bit, 64-bit system and WinCE, Linux, for Mac system Power output: Support 5V / 500mA, 3.3V / 100mA power output Operation method: Switch the button to realize USB, TTL, RS485 and RS232 function transformation Indicators: Connect, receive, send light Communication: The maximum baud rate is up to 2Mbps Circuit board: CP2012 chip Module interface: The module has serial port TTL (VCC, GND level, TX, RX interface), serial port RS232 (VCC, GND level, TX, RX interface), serial RS485 of the A, B interface. Driver download: Click to open Package includes: 5 x USB to RS485 RS232 TTL Serial Port Module

Overview: Optical isolation USB to TTL Serial Module Equipped with CH340T USB to serial chip, achieved the power and TTL signal isolation, High-speed and stability, it could  avoid the damage of USB and computer blue screen or other issues while use the USB to TTL serial port module, due to improper operation or other external impact on the computer  , could improve the safety of debugging. The function and characteristics: 1. Onboard 500mA self-recovery fuse and 5V isolated power supply module to protect the computer from damage 2. Onboard stable CH340T USB to serial chip 3. Serial TTL level through the optocoupler isolation, fast (up to 921600bps), high reliability 4. Output TX RX end with protection diode function, can improve the impact resistance 5. Computer USB end and serial port output end realize complete electrical isolation 6. Output TTL level can be set to 3.3V / 5V 7. Serial output maximum output current of 150mA 8. The board size: 55x26mm Feature: - 3.3V, 5V: Output supply voltage and TTL level switching pin - VCC, GND: Power supply output pin - The TX, RX, GND and VCC pins of the serial port module are connected to the RX, TX, GND, and VCC pins of the user equipment. When the isolated serial port module VCC pin with a jumper cap 5V, the output 5V TTL level and power supply voltage; while VCC pin with 3.3V jumper cap, the output level of 3.3V TTL and power supply voltage. The following is an example of using the isolated serial interface module to debug the 3.3V ESP8266 module (With the jumper cap to isolate the serial port module VCC and 3.3V shorted, isolated serial port module TX, RX, GND, VCC respectively ESP8266 RX, TX, GND, VCC), as the picture shows: The background description of using Isolated serial port module: USB interface was already one of the interfaces that most commonly used by engineers to debug product development. USB interfaces are not only often used in contact with the human body, but also in many cases, it also supplies power to external devices. Strong external power, strong interference may cause damage to the computer USB port or motherboard, then electrical isolation becomes particularly important. LC optically isolated USB to TTL serial port module is suitable for the following occasions: 1. Electrical equipment which containing strong electricity USB devices with high power (such as high voltage, inverter, motor drive, etc.) connact to computer USB may burn out the USB interface, be sure to isolate to ensure that the computer USB port, motherboard and personal safety, can effectively avoid USB Mouth damage and personal injury. 2. Electrical equipment with Strong interference  Such as motor drives, inverters and other great interference itself, into the USB port may lead to computer crashes, blue screen, no response. You can isolate the USB interface through this device to avoid interference with the computer. 3. Noise-sensitive equipment The computer itself is a noise source, through the isolated USB port, you can avoid high-frequency interference to the computer transmission to sensitive devices, and thus better access to data, such as audio equipment, precision measuring equipment and medical equipment.  4. Ordinary electronic equipment For ordinary electronic equipment, through the isolation can effectively avoid operational errors caused by short-circuit damage to the computer USB port, blue screen and other issues, greatly improving the security of the operation. P.S: As there is a certain error of the isolated serial module 5V to 5V above the isolated power supply, so when the VCC through the jumper cap 5V pin and no load when the output power supply voltage will be about 5.4V, but do not worry, when connected to the user equipment, After the device output voltage will automatically drop to 5V or so. Package included: 1 x  High-speed Isolation USB To TTL Serial Module

Description: USB TO RS232 TTL PL2303HX Auto Converter Module Adapter 5V Output, provides the best and convenient way to connect your RS232 TTL devices or DEMO BRD. To your computer, via the usb port. Specification: Built-in TTL COM PC-PL2303HX Chip Standard USB type A male and TTL 4 pin connector Cable length: 1000mm (39 3/8 in) Simple and Easy way to give USB support to your designs Available for Linux, Mac, WinCE and Windows (XP, 2003), Vista, Win 7 Black cable-----GND Green cable----TXD White cable----RXD Red cable ---- VCC (5V) PL2303 Windows Driver Download Connection method: Brush requires only three lines, generally used only three signal lines RX TX GND, VCC. Note: After setting 3.3V and 5.0V output (this is to the microcontroller power supply, no need to upgrade the machine) please put the small plate unplug from the computer, set the jumper to take, do not charged to avoid damage to the device. Voltage: 5V. All you have to do is pop the plastic cover near the USB connector and re-solder the power from 5v to 3.3v to support 3.3v parts. Package included: 5 x USB to RS232/TTL PL2303HX cable adapter module

Features: Supports C's optical transportation wireless master flash: In the optical transportation wireless flash shooting, the YN568EX III can be used as a master unit to trigger YONGNUO and C's EX series speedlite(except the YN585EX), and supports 4 channels, realize wireless TTL, manual flash and stroboscopic flash. Compatible with C and N's optical transportation wireless slave flash: One YN568EX III can respectively accept the master unit of YN600EX-RT II, YN568EX II, YN568EX III, 600EX(II)-RT, 580EX II, SB-910/900/800/700, Nikon internal flash and for Canon commander and wireless signal of 7D/60D/600D, realizes external TTL, manual flash and stroboscopic flash. GN58@ISO100, 105mm, and supports automatic & manual zooming(24-105mm): High index TTL flash, supports TTL, M, Multi flash; and supports supports automatic & manual zooming, the focal length can be varied between 24-105mm. Supports high speed sync(HSS) flash and with high speed recycling(2s) system: The YN568EX III can synchronize with all shutter speeds, realize TTL and manual flash, 1/8000s maximum shutter sync; and the recycling time for full output just takes 2 seconds. Multiple trigger modes, automatic settings saving and custom setting supported: YN568EX III can be triggered by the camera set-top, PC synchronization trigger and wireless optical trigger off the camera. Supports firmware upgrade: The YN568EX III is equipped with USB interface, you can download the latest firmware from YONGNUO official website to upgrade the speedlite. Equipped with large-size LCD display and 2.5mm PC interface, and supports the battery remaining power real-time display, convenient to use. Specifications: Circuit design: Insulated Gate Bipolar Transistor (IGBT) Guide No.: 58 (ISO 100, 105mm) Flash mode: TTL, M, Multi Trigger mode: On-camera, Sc, Sn, S1, S2 Zoom range: 24, 28, 35, 50, 70, 80, 105mm Vertical rotation angle: -7~90 degrees Horizontal rotation angle: 0~270 degrees Power supply: 4 x AA batteries(not included; Alkaline or NI-MH are usable) Lighting times: 100~1500 times (with AA alkaline battery) Recycle time: Approx. 2s (with new AA alkaline battery) Color temperature: 5600k Flash time: 1/200s~1/20000s Flash control: 8 levels of output control (1/128~1/1), 29 levels of fine tuning in total External interface: hot shoe, PC port, USB port Wireless triggering distance: 20~25m indoors, 10~15m outdoors Additional features: Master flash, High speed sync, Rear-curtain sync, FEC, FEB, FE lock, electric zoom of flash head, sound prompt, auto-save setting, PC sync, USB port, power saving mode, overheating protection, advanced options setting. Item Size: 6.2 x 7.2 x 18.8cm/ 2.4 x 2.8 x 7.4in(Extended state) Item weight: 383g/ 13.5oz Package size: 21.5 x 9.5 x 8cm / 8.5 x 3.7 x 3.1in Package weight: 565g / 1.2lbs Compatible with: Hot shoe TTL mode: For Nikon D7400 D7300 D7200 D7100 D5600 D5500 D5400 D5300 D5200 D5100 D5000 D3500 D3400 D3300 D3200 D3100 D3000 D700 D800E D800 D810 D610 D750 D300s D200 D100 D80 D90 D40 D40x D60 D4 D3. Wirelss TTL Slave mode: For Nikon Commander SU-800 For Nikon SB-910, SB-900, SB-800, SB-700, Commander SU-800 Camera with CLS i-TTL system: D4, D3x, D3s, D3, D2x, D700, D300s, D300, D200, D7000, D90, D80 For Canon 7D 6D 600D 650D For Canon Flash 580EX II For Canon ST-E2 Commander Package Included: 1 x YN568EX III Speedlite 1 x Mini Stand 1 x Protecting Bag 1 x User Manual(English & Chinese)

*Fully Support TTL Autoflash, 1/8000s High-Speed Sync, Multi Flash, Manual Flash, Flash Exposure Compensation, TCM Transform Function, Magnfication Function, One-Shoot & Multi- Shoot Setting, Group Modeling Lamp Control, Group Zooming, Adjusting All Groups' Output Value Simultaneously, etc *Add 01 to 99 Wireless ID settings,Which Can Only Achieve Triggering When the channels and Wireless IDs of the Master and Slave Unit are Set to the Same,Avoiding Signal interference effectively *11 Customizable Functions,Extra-large LCD panel, 5 group buttons and 4 function buttons offer convenient manipulation *Built-in Godox 2.4G Wireless X System & Versatile Using Methods:e.g. As a wireless Godox Trigger for camera flash,outdoor flash and studio flash; As a Wireless Speedlites Trigger;As a Wireless Shutter release Trigger;As a flash(without Godox X system) trigger with 2.5mm Sync Cord Jack *Godox XPro-S High Speed Sync Flash Transmitter is compatible camera: Sony series cameras (TTL autoflash) Support for the cameras that have PC sync socket More Feautures FE lock 11 Customizable Functions Manual Flash 1/1 - 1/256 Power Modeling Light Status Control Adjusts the Flash Zoom Coverage for Each Group Selective Transmission of Data Conserves Energy and Battery Life Magnification Function Displays Details of Each Group Settings Global Adjustments to Exposure Values for Multi-Group in M Mode 5 Group Buttons and 4 Function Buttons Offer Convenient Manipulation Support Type-C USB Firmware Upgrade and Wireless Triggering by 2.5mm Sync Cord Jack Compatible Camera: Sony series cameras (TTL autoflash) Support for the cameras that have PC sync socket Flash Exposure Control TTL Autoflash: Sony Manual flash mode: Yes Multi (Stroboscopic) flash mode: Yes Function HSS (High-speed sync): Yes Second-Curtain Sync: Yes Flash exposure compensation: Yes,3 Stops in 1/3 stop increments Flash exposure lock: Yes Auto Focus Assist: Yes Modeling Lamp Control: Control the modeling lamp by the flash trigger Beeper: Control the sound of the flash trigger Wireless Setting: The receiver end can control the camera shooting through the 2.5mm sync cord jack ZOOM setting: Adjust the ZOOM coverage value from the transmitter TCM function: Transforms the TTL shooting value into the output value in M mode Firmware upgrade: Upgrade through the Type-C USB port Memory function: Settings will be stored 2 seconds after last operation and recover after a restart Wireless Flash Wireless Signal Range: >328 feet / >100 Meters Remote System: 2.4GHz Modulation Mode: MSK Channels: 32 Wireless ID: 01-99 Groups: 16 Dimensions: 3.5x2.3x2.0"/ 90x58x50mm Display: Large LCD panel with customizable backlight PACKAGE CONTENTS: 1* Godox Xpro-S 1* Product Manual 1* CONXTRUE USB LED Free Gift

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. Support WINDOWS 98 / ME / 2000 / XP / Server 2003 / VISTA / Server 2008 / Win7 / Win8 32 Bit / 64 2. Support USB1.1 or USB2.0/USB3.0 for communication. 3. Simulation interface, you can upgrade serial peripherals. 4. Supports common MODE contact signal. 5. Supports IRDA SIR infrared communication. 6. Information download here 7. Provide RS232, RS485, RS422 interface. 8. Programming does not affect the target board program runs Package includes: 10 x Adapter 10pcs 3.3V 5V USB to TTL Converter CH340G UART Serial Adapter Module STC 10pcs 3.3V 5V USB to TTL Converter CH340G UART Serial Adapter Module STC 10pcs 3.3V 5V USB to TTL Converter CH340G UART Serial Adapter Module STC

The Phottix Odin II TTL Flash Trigger — with new cutting-edge technology and features. The Odin II interface and control system has been overhauled making it faster and easier to use. It features 5 groups with individual buttons and a control dial for quickly adjusting flash power levels. An AF assist light has been added for improved focusing in low light environments. With 32 channels and a new Digital ID function, the Odin II offers photographers a way to personalized their Odins and prevent triggering from other nearby triggers.This Odin II TTL Transmitter (TCU) is compatible with Nikon DSLRs and compatible flashes. It will also control the Phottix Indra and Mitros+ TTL Transceiver Flash.Use your TTL flash off camera with full TTL functionsHigh Speed Sync 1/8000s*Manual power and TTL EV adjustmentsChange flash zoom and modelling light powerDigital ID to eliminate interference, 10000 unique ID numbersLCD display for visual feedbackUSB port for firmware upgradesGroup buttons and control dial32 Channels5 Groups (A/B/C/D/E)2.4GHz frequency100m+ rangeAF Assist LightCompatible with Phottix Indra, Phottix Mitros+, Odin I, Strato II, Strato I, Atlas II*on compatible camerasIncludes: Odin II Transmitter for Nikon, 2x AA Battery, USB Cable, Bag, User Manual (USB)

The Phottix Odin II TTL Flash Trigger — with new cutting-edge technology and features. The Odin II interface and control system has been overhauled making it faster and easier to use. It features 5 groups with individual buttons and a control dial for quickly adjusting flash power levels. An AF assist light has been added for improved focusing in low light environments. With 32 channels and a new Digital ID function, the Odin II offers photographers a way to personalized their Odins and prevent triggering from other nearby triggers.This Odin II TTL Transmitter (TCU) is compatible with Canon DSLRs and compatible flashes. It will also control the Phottix Indra and Mitros+ TTL Transceiver Flash.Use your TTL flash off camera with full TTL functionsHigh Speed Sync 1/8000s*Manual power and TTL EV adjustmentsChange flash zoom and modelling light powerDigital ID to eliminate interference, 10000 unique ID numbersLCD display for visual feedbackUSB port for firmware upgradesGroup buttons and control dial32 Channels5 Groups (A/B/C/D/E)2.4GHz frequency100m+ rangeAF Assist LightCompatible with Phottix Indra, Phottix Mitros+, Odin I, Strato II, Strato I, Atlas II*on compatible camerasIncludes: Odin II Transmitter for Canon, 2x AA Battery, USB Cable, Bag, User Manual (USB)

Descriptions: Compatible with Pentax P-TTL: A YN585EX supports receiving wireless signal from the master unit of AF-360FGZ, AF540FGZ II and other Pentax cameras. It also supports 4 channels, off-camera TTL and manual flash. Completely Support TTL Function: YN585EX supports FEC, FEB, Rear-curtain Sync and Red Eye Reduction. TTL flash with High Guide Number: GN58@ ISO100 105mm supports TTL, M and MULTI mode. Multiple Trigger Synchronous Mode Supported: Wireless triggered by the built-in flash or master flash, or triggered in S1/S2 pre-flash avoidance mode. Firmware Upgrade: USB port accepts to download the latest firmware and upgrade the speedlite by YONGNUO official website. Zoom Range 20-105mm: Supports auto and manual zooming, the flash can coverage can be changed between 20~ 105mm. Ultra-fast Charging Recycle System: Recycle time for up to 4-5seconds and full-output recycle time even just takes 3 seconds. Display real-time remaining battery power: YN585EX supports to display remaining battery power in real time. Sound Prompting System: Different sound indicates the flash mode which adds additional convenience. AF-assist beam for focusing under low light or low-contrast conditions. Advanced Options Settings and Auto Save settings. Equipped with Big Size LCD Display Screen, Standard PC synchronous Interface. Suit for: Pentax K3II Ks2 K5 K50, K100 K100D K200D K-7 K-x K-r K-5 K-01 K-30 K-5II K-5IIS K-500 K-3 K110D K-m K-S1 K-S2 K-1 K-70 Specifications: Circuit design: Insulated Gate Bipolar Transistor (IGBT) Guide No.: GN58@ ISO100, 105mm Flash mode: P-TTL M Multi Trigger Mode: SP, S1,S2 Zoom range: AUTO, 20, 24, 28, 35, 50, 58, 70,80,105mm Vertical Rotation angle: -7~90 degrees Horizontal rotation angle: 180 Degrees towards the left/right Power supply: 4×AAsize batteries (Alkaline or Ni-MH are usable) (Battery Not Include) Lighting times: 100~1500 times (AA alkaline cell used) Recycle time: 3-5 seconds (AA alkaline cell used) Color temperature: 5600k Flash time: 1/200s~1/20000s Flash control: 8 levels of output control (1/128~1/1), 29 levels of fine tuning External interface: hot shoe,PC port, USB Port firmware upgrade: Yes AF-assist beam: Yes Additional features: Rear-curtain sync, FEC, FEB, the electronic flash head zooming, sound prompt, automatically saving setting, PC port, power saving mode and over heat protection, Advance option's function,Master/Slave function Package Included: 1 x YN585EX Speedlite For Pentax 1 x Mini Stand 1 x User Manual 1 x Soft Case 1 x Retail Box

Buy Waveshare PL2303 USB UART Board Communication USB to TTL USB to Serial M for R225.00

Phottix Mitros+ TTL Transceiver Flash Phottix Mitros hot shoe flashes have quickly become the industry's gold standard in TTL flashes. The Mitros+ is the 'go to' flash for wedding and event photographers.The Phottix Mitros+ TTL Transceiver Flash for Nikon is the perfect all-in-one triggering and hot shoe flash solution for use with Nikon DSLRs. It's a powerful, durable and easy-to-use hot shoe flash with built-in Odin Transmitter. Use the Mitros+ on-camera to control and trigger other Mitros+ flashes or compatible flashes using Phottix Odin Receivers. The Mitros+ also offers a built-in Odin Receiver, Strato II Receiver and functions in Master or Slave mode with wireless triggering.GN:58 Nikon-compatible TTL flashBuilt-in Phottix Odin Transmitter and Receiver, Strato II ReceiverOptical slaveNikon-compatible Master/Slave IR triggering modesETTL I/II, Manual and Multi Stroboscopic modesHigh Speed Sync and Second Curtain SyncAF Assist lightFlash zoom: 24-105mmExternal battery port, 3.5mm sync portQuick Flash modeMemory functionsRotating/elevating flash headPowered by 4x AA alkaline or NiMH batteriesDimensions: 203 x 78 x 58mmWeight: 427g (without batteries)Includes: Mitros+ Flash for Nikon, 3.5mm to 3.5mm Cable, USB Cable, Battery Port Adapter, Flash Stand, Diffuser, Carry Bag, Manual (USB Drive)

Yongnuo YN-622N II Wireless Flash Trigger Receiver TTL for Nikon D4 D7000 The new upgrade version YN622N II supports receiving the trigger signal of the YN560-TX/ RF605 (603MODE)/ RF603II Series products, with multi aspects improved, equipped with quick lock design and supports USB firmware upgrade. Specification We added the quick lock design, you can fasten the hot shoe of this flash trigger with your camera or flash. It supports USB Firmware upgraded. It supports YN-622N, YN-622N-TX, RF-605N, RF-603 II and YN560-TX communication mode. **TTL mode (622 mode), you can use YN-622N, YN-622N II, YN-622N-TX together, ***Manual mode (603-RX mode), you can use YN-560TX, RF-603 II, RF-605N as transmitter, and use YN-622N II as receiver. Main Function *Quick lock design *Supports USB firmware upgrade *Supports "622" communication mode,"603-RX" communication mode *Compatible flash mode: i-TTL, Manual flash *Compatible Shutter sync: front-curtain sync, rear- curtain sync and high-speed sync(HSS/FP), the highest sync speed is 1/8000s* *Support remote set the parameters of flash through the transceiver (Remote Control Mode) *Support i-TTL/Manual/Repeating flash mode mix using(Mix Control Mode) *Support the flash installed on transmitter(on-top flash)and supports i-TTL function *Support the use of master unit on transmitter sets the parameters of each group(Master Control Mode) *Support FEC, FVL function *Support modeling flash and red-eye reduction flash *Support flash zooming (auto) *Built-in AF assist beam emitter (AF Lamp) *Settings saved automatically *Compatible with YongNuo/ Nikon series flashes *Support PC port triggering strobe flashes *PC port support front/rear curtain sync and high-speed sync(Super Sync)function *Support single-contact of camera & flash triggering (max sync speed is 1/250s) Suitable With Camera: -D70 D70S D60 D80 D90 D4 D3X D3S D3 D2X D40X D40 -D800E D800 D700 D600series D300S D300 D200 -D7000 D5300 D5200 D5100 D5000 D3200 D3100 D3000 Flash compatible (i-TTL): -SB600 SB700 SB800 SB900 SB910 -YN467N YN468N(II) YN560II YN560III YN565N YN568N Package Include - 2 x YN-622N II Transceivers -1 x Instruction in English and Chinese -1 x Original Yongnuo Box Note:Batteries & Camera &Flash not included 

Buy 3pcs USB to TTL 3.3V 5V FT232 LilyPad328 Mini USB Adapter Module for R251.71

Buy 5pcs USB to Serial Module Downloader CP2102 USB to TTL STC Download Compatible for R287.68

Buy 2Pcs Waveshare FT232 Module USB to Serial USB to TTL FT232RL Communicati for R289.00

Buy 2Pcs Waveshare FT232 Module USB to Serial USB to TTL FT232RL Communication Modu for R319.54

Buy Waveshare FT232 Module USB to Serial USB to TTL FT232RL Communication Module for R229.42

Buy 2Pcs Waveshare FT232 Module USB to Serial USB to TTL FT232RL Communication Module Micro Port Flas... for R359.00

Buy 10pcs CP2102 USB to TTL Serial Adapter Module USB to UART Converter Debugger Programmer for R535.22

Buy 3pcs CP2102 USB to TTL Serial Adapter Module USB to UART Converter Debugger Pro for R320.88

Buy RobotDyn USB to TTL UART CH340 Serial Converter Micro USB 5V/3.3V IC CH340G Module for R229.00

Buy PL2303 USB to TTL USB to Serial Port PL2303 Module Brush Line 4PIN DuPont Cable for R225.00

Phottix Mitros hot shoe flashes have quickly become the industry¿s gold standard in TTL flashes. The Mitros+ is the 'go to' flash for wedding and event photographers.The Phottix Mitros+ TTL Transceiver Flash for Canon is the perfect all-in-one triggering and hot shoe flash solution for use with Canon DSLRs. It's a powerful, durable and easy-to-use hot shoe flash with built-in Odin Transmitter. Use the Mitros+ on-camera to control and trigger other Mitros+ flashes or compatible flashes using Phottix Odin Receivers. The Mitros+ also offers a built-in Odin Receiver, Strato II Receiver and functions in Master or Slave mode with wireless triggering.GN:58 Canon-compatible TTL flashBuilt-in Phottix Odin Transmitter and Receiver, Strato II ReceiverOptical slaveCanon-compatible Master/Slave IR triggering modesETTL I/II, Manual and Multi Stroboscopic modesHigh Speed Sync and Second Curtain SyncAF Assist lightFlash zoom: 24-105mmExternal battery port, 3.5mm sync portQuick Flash modeMemory functionsRotating/elevating flash headPowered by 4x AA alkaline or NiMH batteriesDimensions: 203 x 78 x 58mmWeight: 427g (without batteries)Includes: Mitros+ Flash for Canon, 3.5mm to 3.5mm Cable, USB Cable, Battery Port Adapter, Flash Stand, Diffuser, Carry Bag, Manual (USB Drive)