Polisher automotive

Polisher Wattage: 1700W No load speed: 800-2400 RPM Supplied with a Ø180mm sponge and backing pad. Application: The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface. The objective of polishing is to remove imperfections in the clear-coat that cause the paint to look dull. Surface imperfections can include swirls, scratches, water spots, etchings, industrial fallout, oxidation, etc. Features: Professionally manufactured for the automotive paint care and detailing industries. Ergonomically designed to reduce fatigue in long term use. The polisher has various hand-held positions to better hold the polisher at angles. Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher. The polisher range: ORDER NO. DESCRIPTION WARRANTY POL01 Polisher, 800W. Supplied with Ø125mm wool buff 6 Months POL02 Polisher, 1200W. Supplied with Ø180mm wool buff 6 Months POL03 Polisher, 1700W. Supplied with Ø180mm sponge pad 6 Months The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it"s lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down. Spare parts for the POL03 polisher: ORDER NO. DESCRIPTION POL03-05 Switch POL03-11 Electrical unit POL03-12 Thumb wheel POL03-14 Brush spring POL03-15 Carbon brushes POL03-16 Carbon brush holder POL03-25 Ball bearing POL03-27 Ball bearing POL03-33 Needle bearing POL03-39 Ball bearing

Polisher Wattage: 1200W No load speed: 1500-3000 RPM Supplied with a Ø180mm wool bonnet buff and backing pad. Application: The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface. The objective of polishing is to remove imperfections in the clear-coat that cause the paint to look dull. Surface imperfections can include swirls, scratches, water spots, etchings, industrial fallout, oxidation, etc. Features: Professionally manufactured for the automotive paint care and detailing industries. Ergonomically designed to reduce fatigue in long term use. The polisher has various hand-held positions to better hold the polisher at angles. Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher. The polisher range: ORDER NO. DESCRIPTION WARRANTY POL01 Polisher, 800W. Supplied with Ø125mm wool buff 6 Months POL02 Polisher, 1200W. Supplied with Ø180mm wool buff 6 Months POL03 Polisher, 1700W. Supplied with Ø180mm sponge pad 6 Months The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it's lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down. Spare parts for the POL02 polisher: ORDER NO. DESCRIPTION POL02-12 Big gear POL02-13 Bearing POL02-16 Aluminium head POL02-19 Fixation knob POL02-24 Armature POL02-29 Field coil (stator) POL02-30 Motor housing POL02-33 Carbon brushes POL02-37-38 Speed control (switch) POL02-40 Rear handle POL02-46 Trigger switch

Description: 6 Inch Vacuum Polisher Air Random Orbital Palm Car Polisher Sander Sanding Pad   Specifications: Average air consumption: 5CFM Maximum speed: 9000 RPM The air pressure: 90 psi Air inlet: 1/4" NPT Overall Length: 150mm   Features: - Grinding speed, reduce operating times. - Uniform and smooth polishing effect. - Non-slip anti-freeze bags, suitable for prolonged use. - Lightweight, low height, easy to use. - Easy to handle and deliver high quality finishes in the body shop and woodworking. - Random orbit action for finishing without turbulence, easy on / off switch. - Handle Tear Drop for great control. - Suitable for coating operations in automotive sheet metal, a zinc supplement soil grinding, shaving, feather edge grinding, wood furniture, metal grinding, all the smooth surface required operations.   Packaged Included: 1 x 6" vinyl face pad 1 x orbital sander 1 x 1/4"air regulator 1 x Manual 1 x Key   More Details:

Double sided wool buff Diameter: Ø230mm Thread/Velcro: 5/8 UNC Application: The double sided wool buff should be used with an automotive polisher. Different compounds, polishes and waxes can be applied to both sides of the buff and then flipped around when needed. This saves time without the need of changing to another buff. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the compound is soluble. Double sided wool buff range: ORDER NO. DIAMETER THREAD MM DS7 Ø180mm M14 MM DS7-2 Ø180mm 5/8 UNC MM DS9 Ø230mm M14 MM DS9-2 Ø230mm 5/8 UNC Adaptors to convert or lenghten the polisher"s thread: ORDER NO. MALE THREAD FEMALE THREAD SPC00055 5/8 UNC 5/8 UNC SPC00053 5/8 UNC M14 SPC00054 M14 5/8 UNC SPC00052 M14 M14 Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Double sided wool buff Diameter: Ø230mm Thread/Velcro: M14 Application: The double sided wool buff should be used with an automotive polisher. Different compounds, polishes and waxes can be applied to both sides of the buff and then flipped around when needed. This saves time without the need of changing to another buff. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the compound is soluble. Double sided wool buff range: ORDER NO. DIAMETER THREAD MM DS7 Ø180mm M14 MM DS7-2 Ø180mm 5/8 UNC MM DS9 Ø230mm M14 MM DS9-2 Ø230mm 5/8 UNC Adaptors to convert or lenghten the polisher"s thread: ORDER NO. MALE THREAD FEMALE THREAD SPC00055 5/8 UNC 5/8 UNC SPC00053 5/8 UNC M14 SPC00054 M14 5/8 UNC SPC00052 M14 M14 Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Double sided wool buff Diameter: Ø180mm Thread/Velcro: M14 Application: The double sided wool buff should be used with an automotive polisher. Different compounds, polishes and waxes can be applied to both sides of the buff and then flipped around when needed. This saves time without the need of changing to another buff. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the compound is soluble. Double sided wool buff range: ORDER NO. DIAMETER THREAD MM DS7 Ø180mm M14 MM DS7-2 Ø180mm 5/8 UNC MM DS9 Ø230mm M14 MM DS9-2 Ø230mm 5/8 UNC Adaptors to convert or lenghten the polisher"s thread: ORDER NO. MALE THREAD FEMALE THREAD SPC00055 5/8 UNC 5/8 UNC SPC00053 5/8 UNC M14 SPC00054 M14 5/8 UNC SPC00052 M14 M14 Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Description: 5 Inch Air Grip Random Orbital Palm Sander 125mm Air Hand Power Tool Polisher Panel Specifications: Free Speed: 9000RPM Max. pressure: 90PSI Sanding pad: 5" / 125mm Air Inlet: 1/4 NPT Air hose: 3/8" Avg. Air consumption:12 CFM(340 l/min) Quantity: 1 x 5" Random Orbital Air Palm Sander 1 x Oil 1 x Wrench 1 x Air regulator 1 x Manual Features: --Grinding speed, shorten operating time. --Uniform and smooth polishing effect. --Antifreeze slip pouches, suitable for prolonged use. --Light weight, low height, easy to operate. --Suitable for automotive sheet metal coating operations, a zinc supplement soil grinding, shaving, feather edge grinding, wood furniture, metal grinding, all the required smooth surface operations. Packaged Included: 1 Set x Air Palm Sander More Details:

Velcro polishing wool buff Diameter: Ø180mm Use backing pad: SPC00119 Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with velcro. Make sure the diameter of the polishing buff is the same as the backing pad"s diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Velcro polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD SPC00123 Ø125mm SPC00120 SPC00125 Ø180mm SPC00119 Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Tie on polishing wool buff Diameter: Ø125mm Use backing pad: TCBP125C / PG338 Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad"s diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Tie on polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD MM4 Ø100mm MM5 Ø125mm TCBP125C / PG338 MM6 Ø150mm TCBP150C MM7 Ø180mm PG33805 MM7-2 Ø180mm PG33805 MM8 Ø200mm MM9 Ø230mm MM9-2 Ø230mm MM10 Ø250mm Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Tie on polishing wool buff Diameter: Ø250mm Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad"s diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Tie on polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD MM4 Ø100mm MM5 Ø125mm TCBP125C / PG338 MM6 Ø150mm TCBP150C MM7 Ø180mm PG33805 MM7-2 Ø180mm PG33805 MM8 Ø200mm MM9 Ø230mm MM9-2 Ø230mm MM10 Ø250mm Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Tie on polishing wool buff Diameter: Ø150mm Use backing pad: TCBP150C Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad"s diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Tie on polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD MM4 Ø100mm MM5 Ø125mm TCBP125C / PG338 MM6 Ø150mm TCBP150C MM7 Ø180mm PG33805 MM7-2 Ø180mm PG33805 MM8 Ø200mm MM9 Ø230mm MM9-2 Ø230mm MM10 Ø250mm Recommended polishing compounds to use: Liquid Shine¿ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine¿ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine¿ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Tie on polishing wool buff Diameter: Ø230mm Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad's diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Tie on polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD MM4 Ø100mm MM5 Ø125mm TCBP125C / PG338 MM6 Ø150mm TCBP150C MM7 Ø180mm PG33805 MM7-2 Ø180mm PG33805 MM8 Ø200mm MM9 Ø230mm MM9-2 Ø230mm MM10 Ø250mm Recommended polishing compounds to use: Liquid Shine™ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine™ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine™ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Velcro polishing wool buff Diameter: Ø180mm Use backing pad: SPC00119 Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with velcro. Make sure the diameter of the polishing buff is the same as the backing pad's diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Velcro polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD SPC00123 Ø125mm SPC00120 SPC00125 Ø180mm SPC00119 Recommended polishing compounds to use: Liquid Shine™ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine™ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine™ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step

Tie on polishing wool buff Diameter: Ø180mm Use backing pad: PG33805 Application: The polishing wool buff should be used with an automotive polisher. Different polishes and waxes can be used with the buff. The buff is fastened onto a rubber backing pad with laces. Make sure the diameter of the polishing buff is the same as the backing pad's diameter. It is necessary to polish a vehicle body panel when: The panel has been newly painted with a clear-coat. Shallow scratch marks need to be removed. The panel has suffered from oxidation. Swirl marks and hologram defects need to be removed. TIP: The buff is washable after use if the polishing compound is soluble. Tie on polishing wool buff range: ORDER NO. DIAMETER USE BACKING PAD MM4 Ø100mm MM5 Ø125mm TCBP125C / PG338 MM6 Ø150mm TCBP150C MM7 Ø180mm PG33805 MM7-2 Ø180mm PG33805 MM8 Ø200mm MM9 Ø230mm MM9-2 Ø230mm MM10 Ø250mm Recommended polishing compounds to use: Liquid Shine™ High cut - Features a silicone, wax and filler free polishing compound to give a high gloss finish on fresh or cured paint. It is capable of removing P1500 grit sanding marks. It can be used on automotive paints, marine gel-coats and on composite surfaces. Liquid Shine™ Fine cut - similar to the High cut polishing compound, but it is designed for use on a ceramic and scratch resistant clear-coat. It is capable of removing P2000 scratch marks. Liquid Shine™ Zero swirl - Very low abrasive for the final step of polishing. Removes holograms and swirl marks. Use a soft compounding sponge as a final step