Ieee802 3at af poe

Buy Planet IEEE802.3at/af to Passive POE Power Converter (12V/19V/24V) for R1,437.00

Intellinet POE Splitter Retail Box 2 year Limited Warranty Product Overview Deliver Power over Ethernet to remote devices. The INTELLINET NETWORK SOLUTIONS PoE+ Splitter allows you to deliver both data and electrical power to non-PoE Ethernet-enabled products using the Cat5 Ethernet cable. Using the PoE Splitter, you can take advantage of Power over Ethernet and place Ethernet-enabled products, such as Network Cameras and Wireless Access Points*, where power outlets are not readily available. Simplify Installation for an Ethernet-based Device Having to manage only an Ethernet cable simplifies the physical installation of the device. Without having to worry about the availability of a power source, you can mount Ethernet-enabled products on a ceiling or outdoors, up to 100m (328 feet)** from a power source. The PoE Splitter is simple to install and requires no tools or software. 802.3af Compliant Power over Ethernet The PoE Splitter can be used to complement any PoE injector unit or midspan switch to provide small to medium-sized businesses a complete end-to-end PoE solution. This unit supports 802.3af and 802.3at, ensuring compatibility with other 802.3af/t PoE-compliant injector units or PSE switches. Adjustable Power Output During the setup, the PoE Splitter can be set to power any compatible 5 V, 7.5 V, 9 V or 12 V Ethernet-enabled device via the volt selector located on the side. Features IEEE 802.3af-compliant PoE splitter Can be used to connect non-PoE IEEE 802.3af/t-compliant devices to a PoE injector or PoE switch Output current, selectable: 5, 7.5, 9 or 12 V DC Power output: 5 V / 4 A, 7.5 V / 2.7 A, 9 V / 2.3 A and 12 V / 1.7 A 10/100 auto-sensing input port automatically detects optimal network speeds RJ45 input port with Auto-MDIX and NWay auto-negotiation support Full/half duplex operation Compact metal case LED for link on PoE input port

Specifications Standard & Protocol: IEEE 802.3, IEEE 802.3u, IEEE 802.3x, IEEE802.3ab, IEEE 802.3af, IEEE 802.3at MTBF: 50,000 hours (about 5 years) Indicator: Link/Act, PoE Status, Power, 100M Fixed Port: 8x 10/100Base-TX RJ45 Ports (Data/Power) Fixed Port: 1x 10/100Base-TX RJ45 Port (Data) Lightning Protection: 6KV Wire-speed forwarding: Supported Switching Capacity: 1.8 Gbit/s MAC Address Table: 4K MAC PoE supply management - Ports 1 to 8 support standard IEEE802.3at/af power (maximum power for each port is 30W)PoE power type is end-span (1245+, 3678- line pair) in full configuration - PoE Max Power Supply58W Input Voltage AC100240V 50/60Hz Input Voltage DC51V /1.25A Power Adapter Operating Temperature: 0~40 Storage Temperature: -40~70 Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Dimensions: 177.5mm x 104mm x 26mm (W D H)

Description Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Tenda PoE30G-AT Gigabit PoE injector The Tenda PoE30G-AT is the IEEE802.3 AT Gigabit PoE injector, which fully conforms to the standard of 802.3, transmitting power through Ethernet cable, the maximum transmission distance can reach 100 meters. The PoE injector has two Ethernet gigabit data ports and an output port combination of data and power. In addition, the device can be used for Ethernet device IEEE802.3af/ compatible PoE power applications such as wireless AP, VoIP phone and web CAM. The power supply of Ethernet cable not only provides system reliability, traditional power grid expansion but also simplifies the deployment of power lines. Features PoE ports support IEEE802.3at and IEEE802.3af standard Equipped with Gigabit port, blazing-fast transfer rate, the maximum transfer rate of up to 30W for a single port Power distance extension of up to 100 meters for the standard cat. 5e and Cat. 6 Ethernet cable Plug and play, no configuration required PoE Performance PoE ports support IEEE802.3at and IEEE802.3af standard Supports AT high power(30W) Power supply distance extension The standard cat’s power distance can be extended to 100 meters. The device can extend the range of PoE power over long distances, and simplify the deployment of power lines so that PD equipment can supply power. Gigabit blazing-fast delivery 10/100M/1000Mbps autosensing RJ45 port provides fast data delivery, supports wire-speed forwarding and MDI/MDIX, plug and play. Stable performance Adopts new chips solution, brings new performance experience, powerful data transfer and power Specifications Description PoE Injector Standard b'&' Protocol Compatible with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3af, IEEE802.3atStandard CSMA/CD, TCP/IP Features Support the powered devices compatible with IEEE802.3af、IEEE802.3at Standard Transmission range up to 100M Plug and play Port 1 GE port 1 datab'&'power output port supporting PoE Indicator PWR, PoE Dimension 131mm*60mm*33mm Power Output 30W Operation Temperature 0℃~40℃ Storage Temperature -40℃~70℃ Operating Humidity 10%~90% (noncondensing) Storage Humidity 5%~90% (noncondensing)

Description M-Link 8-Ports 10/100/1000Mbps PoE Unmanaged Network Switch TXE143 is a 10-Ports 10/100/1000Mbps Desktop PoE network switch that provides a seamless network connection. These PoE Ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs). In this situation, the electrical power is transmitted along with Data in one single Cable. Allowing you to expand your network where there are no power lines or outlets. Where you wish to fix devices such as APs, IP Cameras or IP Phones, etc. VLAN isolation to meet security monitoring requirements Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic. And ensure that the upstream channel is unobstructed. TXE143 is easy to install and use. It requires no configuration and installation. With desktop design, outstanding performance, and quality. The 10-Ports 100/100/1000Mbps Desktop PoE switch is a great selection for expanding your home or office network Features: Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3ab, IEEE802.3x,IEEE802.3az, IEEE802.1q Ethernet standards Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE Port, all power up to 120W VLAN isolation to meet security monitoring requirements Support 10 x10/100/1000Mbps Auto-negotiation RJ45 ports with 8 ports PoE function (port1-port8) Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode; LED indicators for monitoring Port Link / Activity; Internal Power Supply, exquisite design, suitable for Desktop use

M-Link 8-Ports 10/100/1000Mbps PoE Unmanaged Network Switch TXE143 is a 10-Ports 10/100/1000Mbps Desktop PoE network switch that provides a seamless network connection. These PoE Ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs). In this situation, the electrical power is transmitted along with Data in one single Cable. Allowing you to expand your network where there are no power lines or outlets. Where you wish to fix devices such as APs, IP Cameras or IP Phones, etc. VLAN isolation to meet security monitoring requirements Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic. And ensure that the upstream channel is unobstructed. TXE143 is easy to install and use. It requires no configuration and installation. With desktop design, outstanding performance, and quality. The 10-Ports 100/100/1000Mbps Desktop PoE switch is a great selection for expanding your home or office network Features: Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3ab, IEEE802.3x,IEEE802.3az, IEEE802.1q Ethernet standards Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE Port, all power up to 120W VLAN isolation to meet security monitoring requirements Support 10 x10/100/1000Mbps Auto-negotiation RJ45 ports with 8 ports PoE function (port1-port8) Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode; LED indicators for monitoring Port Link / Activity; Internal Power Supply, exquisite design, suitable for Desktop use

Intellinet PoE-Powered 5-Port Gigabit Switch with PoE Passthrough - 4 x PSE PoE ports, 1 x PD PoE port, IEEE 802.3at/af Power-over-Ethernet (PoE+/PoE), IEEE 802.3az Energy Efficient Ethernet, Desktop, Retail Box, 2 year Limited Warranty

Description Tenda 6-Port 10/100M Desktop Network Switch with 4-Port PoE TEF1106P-4-63W is an unmanaged desktop network PoE switch with 2 uplink ports, independently designed by Tenda. Compliant with IEEE 802.3at/af standards, it can identify PoE-powered devices intelligently. The switch supplies a maximum PoE power output of 63 W and 30 W for a single port. Featured with extending mode and QoS function, TEF1106P-4-63W is an ideal choice for SMBs, supermarkets and restaurants with small-sized video surveillance requirements. Features: 6KV lightning protection 250m Extend mode QoS Dual uplink ports Up to 250 meters long distance transmission under the Extend Mode, beyond hundred meters transfer limitation Due to the complex monitoring environment, the distance from each terminal to the monitoring centre is different. Some even more than a hundred meters. TEF1106P-4-63W can support 250 meters of data transmission in the Extend mode, which can save the cost of your project with fewer devices used. Excellent lightning Protection TEF1106P-4-63W supports professional lightning protection of 6KV for uplink ports b'&' 4KV for power, which can protect the switch from the inductive lightning strike coming from the thunderstorm weather. QoS Priority design makes the key video data to be prioritized 1-2 ports support the QoS Priority function, and it will prioritize them when meeting network congestion. Which can ensure the network stable and fluent transmission of the surveillance video without breaking up. b'/xc2/xa0'

Tenda 6-Port 10/100M Desktop Network Switch with 4-Port PoE TEF1106P-4-63W is an unmanaged desktop network PoE switch with 2 uplink ports, independently designed by Tenda. Compliant with IEEE 802.3at/af standards, it can identify PoE-powered devices intelligently. The switch supplies a maximum PoE power output of 63 W and 30 W for a single port. Featured with extending mode and QoS function, TEF1106P-4-63W is an ideal choice for SMBs, supermarkets and restaurants with small-sized video surveillance requirements. Features: 6KV lightning protection 250m Extend mode QoS Dual uplink ports Up to 250 meters long distance transmission under the Extend Mode, beyond hundred meters transfer limitation Due to the complex monitoring environment, the distance from each terminal to the monitoring centre is different. Some even more than a hundred meters. TEF1106P-4-63W can support 250 meters of data transmission in the Extend mode, which can save the cost of your project with fewer devices used. Excellent lightning Protection TEF1106P-4-63W supports professional lightning protection of 6KV for uplink ports b'&' 4KV for power, which can protect the switch from the inductive lightning strike coming from the thunderstorm weather. QoS Priority design makes the key video data to be prioritized 1-2 ports support the QoS Priority function, and it will prioritize them when meeting network congestion. Which can ensure the network stable and fluent transmission of the surveillance video without breaking up. b'/xc2/xa0'

Tenda TEG1124P-24-250W 24-Port Gigabit Ethernet Switch TEG1124P-24-250W is a Tenda Gigabit Ethernet PoE switch that o ers 24 10/100/1000 Mbps Base-TX RJ45 ports. Ports 1-24 comply with the IEEE 802.3af standard (maximum PoE power output: 15.4 W) and 802.3at standard (maximum PoE power output: 30 W). The switch o ers a maximum PoE power output of 225 W and can supply power to and exchange data with APs, IP cameras, and IP phones through CAT5 cables. It also provides simple management modes such as CCTV, VLAN, and Isolation to help reduce cabling costs of IP terminals like APs and IP cameras 6KV Lightning Protection PoE Switch is the only engineering switch In real projects, APs and cameras are often installed outdoors or at an elevated location, which increases the chance of lightning strikes on cameras and PoE-powered switches. The result is that individual devices are damaged when the outcome is light, and even the whole local area network is damaged. Tenda TEG11 series switches have a professional lightning protection design – 6KV Lightning Protection for Ports and the power, and they have two levels of protection design respectively, which effectively suppress the lightning current from the network cable and power supply, equivalent to adding a security wall to the entire network monitoring system. The test standard is much higher than the national CCCrequest. In the thunderstorm, Tenda TEG11 series switches can also provide a stable and reliable service to the surveillance network and guarantee the normal transmission of the picture. CCTV, Standard, VLAN and Isolation Operation Modes Offered CCTV: in this mode, the port cache is optimized and PoE ports 1-8 have higher priorities over the other ports. All the ports of the switch can communicate with each other. If multiple IP cameras are connected to the switch, you are recommended to enable this mode and connect the uplink port of the switch to the upstream device to which the monitoring computer connects. This ensures smoother monitoring video playback. Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. VLAN: ports 1 to 22 of TEG1124P-24-250W are isolated from each other, but can communicate with ports 23 and 24 (uplink ports) respectively.Solid DIP switch to isolate ports to prevent broadcast storm and defend DHCP spoofing. Isolation: ports 1 to 12 and Ports 13 to 24 of TEG1124P-24-250W belong to two different VLAN. This mode can be used to isolate supervision network and wireless network to make them not interfere with each other. 225W PoE power supply simplified wiring Ports 1-24 comply with the IEEE802.3af and IEEE802.3at power supply standards. The entire switch offers a maximum PoE power output of 225W, whereas each port offers a maximum PoE power output of 30 W. The ports can be used to supply power to and exchange data with APs and IP cameras. Specifications Standard b'&' Protocol IEEE 802.3/IEEE 802.3u/IEEE 802.3ab/IEEE 802.3x/IEEE 802.3af/IEEE 802.3at Indicator 24*Link/Act per device 24*PoE per device 1*Power per device Interface 24 10/100/1000Base-T ports(Data/Power) Lightning Protection 6KV Store b'&' Forward Yes exchange capacity 48 Gbp Packet Forwarding Rate 35.6Mpps RAM Data Buffer 4Mb MAC Address Table 4K PoE supply management Port 1-24 support IEEE802.3at/af PoE standard PoE through pin 1 2 4 5 +/3 6 7 8 – Input Power AC: 100-240V～50/60Hz Dimension 440*178*44mm(W x D x H) Power Consumption in full conguration: b' PoE Max Power Supply: 225W Port Features Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. CCTV: the port cache is optimized and PoE ports 1-8 have higher priorities over the other ports. All the ports of the switch can communicate with each other. VLAN: ports 1 to 22 are isolated from each other, but can communicate with ports 23 and 24(uplink ports) respectively. Isolation: ports 1 to 12 and Ports 13 to 24 belong to two different VLAN. This mode can be used to isolate supervision network and wireless network to make them not interfere with each other. Environment Operating Temperature: 0℃~40℃ (32℉~104℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Description Tenda 9-Port Fast Unmanaged Switch TEF1109P-8-102W is a Tenda Network switch that offers 9 10/100M RJ45 ports. Ports 1-8 comply with the IEEE802.3af standard (maximum PoE power output: 15.4w) and 802.3at standard (maximum PoE power output: 30W). The Tenda Network switch offers a maximum PoE power output of 92W and can supply power to exchange data with APs, IP cameras, and IP phones through CAT5e cables. It also provides simple management modes such as Standard, VLAN. Thus, F1109P-8-102W is a perfect choice for SMBs, hotels, and offices to have small-scale HD surveillance and wireless networking. Transmission Distance up to 250m With the extension technology, data can be transmitted through 250 meters cable which would be a cost-effective replacement for extenders and optical fibres. Excellent Lightning Protection The switch supports 6 kV lightning protection for the uplink port, protecting the switch from thunderstorms and making it more stable. What’s Special for TEF1109P-8-102W: Simple Port VLAN Setup With VLAN Mode on, ports 1 to 8 are isolated from each other, enabling the switch to isolate broadcast storms, improving LAN security and data transmission. What’s Special for TEF1109P-8-102W: Enjoy Super HD Video Screen Equipped with a 1024KB large packet buffer, it ensures smooth streaming even when eight HD IP cameras of 500W are working simultaneously. Integrated with Smart Power Management Chip Makes the Switch Get Rid of Overload It includes chips with a smart power management function and an integrated professional chip control algorithm, which can accurately calculate the output power. When the power of the receiving equipment exceeds the rated power (92W) of the PoE switch, the low priority port will automatically power off to avoid the over-run of the equipment and prolong the service life of the equipment. Outstanding PoE Power Supply Ports 1-8 support IEEE 802.3at and IEEE 802.3af PoE standard. It provides 30W maximum PoE output with a single port and 92W for the whole device. Specification Standard b'&' Protocol IEEE 802.3/IEEE 802.3u/IEEE 802.3x/IEEE 802.3af/IEEE 802.3at LED 9*Link/Act per device 1*Power per device Interface 8 10/100Base-T ports(Data/Power) 1 10/100Base-T ports(Data) Lightning Protection 6KV for uplink port Store b'&' Forward Yes Exchange capacity 1.6 Gbps Packet Forwarding Rate 1.34Mpps Packet buffer 1Mb MAC Address Table 2K PoE supply management Port 1-8 support IEEE802.3at/af PoE standard PoE through pin 1 2 4 5 + 3 6 7 8 – Input Voltage AC: 100-240V～50/60Hz Dimension 177.5*104*26mm (W x D x H) Port Features Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. VLAN: ports 1 to 8 are isolated from each other, but can communicate with ports 9 (uplink port) respectively. Humidity Operating Temperature: 0℃~40℃ (32℉~104℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Tenda 9-Port Fast Unmanaged Switch TEF1109P-8-102W is a Tenda Network switch that offers 9 10/100M RJ45 ports. Ports 1-8 comply with the IEEE802.3af standard (maximum PoE power output: 15.4w) and 802.3at standard (maximum PoE power output: 30W). The Tenda Network switch offers a maximum PoE power output of 92W and can supply power to exchange data with APs, IP cameras, and IP phones through CAT5e cables. It also provides simple management modes such as Standard, VLAN. Thus, F1109P-8-102W is a perfect choice for SMBs, hotels, and offices to have small-scale HD surveillance and wireless networking. Transmission Distance up to 250m With the extension technology, data can be transmitted through 250 meters cable which would be a cost-effective replacement for extenders and optical fibres. Excellent Lightning Protection The switch supports 6 kV lightning protection for the uplink port, protecting the switch from thunderstorms and making it more stable. What’s Special for TEF1109P-8-102W: Simple Port VLAN Setup With VLAN Mode on, ports 1 to 8 are isolated from each other, enabling the switch to isolate broadcast storms, improving LAN security and data transmission. What’s Special for TEF1109P-8-102W: Enjoy Super HD Video Screen Equipped with a 1024KB large packet buffer, it ensures smooth streaming even when eight HD IP cameras of 500W are working simultaneously. Integrated with Smart Power Management Chip Makes the Switch Get Rid of Overload It includes chips with a smart power management function and an integrated professional chip control algorithm, which can accurately calculate the output power. When the power of the receiving equipment exceeds the rated power (92W) of the PoE switch, the low priority port will automatically power off to avoid the over-run of the equipment and prolong the service life of the equipment. Outstanding PoE Power Supply Ports 1-8 support IEEE 802.3at and IEEE 802.3af PoE standard. It provides 30W maximum PoE output with a single port and 92W for the whole device. Specification Standard b'&' Protocol IEEE 802.3/IEEE 802.3u/IEEE 802.3x/IEEE 802.3af/IEEE 802.3at LED 9*Link/Act per device 1*Power per device Interface 8 10/100Base-T ports(Data/Power) 1 10/100Base-T ports(Data) Lightning Protection 6KV for uplink port Store b'&' Forward Yes Exchange capacity 1.6 Gbps Packet Forwarding Rate 1.34Mpps Packet buffer 1Mb MAC Address Table 2K PoE supply management Port 1-8 support IEEE802.3at/af PoE standard PoE through pin 1 2 4 5 + 3 6 7 8 – Input Voltage AC: 100-240V～50/60Hz Dimension 177.5*104*26mm (W x D x H) Port Features Standard: the switch functions as a common unmanaged switch and all the ports of the switch can communicate with each other. VLAN: ports 1 to 8 are isolated from each other, but can communicate with ports 9 (uplink port) respectively. Humidity Operating Temperature: 0℃~40℃ (32℉~104℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing

Description M-Link 8 PORT 10/100 POE+2 PORT Switch 8PORT 10/100 POE+2PORT – TXE188 8-Ports 10/100Mbps PoE + 2-Ports 10/100Mbps Unmanaged Ethernet Switch Description TXE188 is a 10-port 10/100Mbps Desktop PoE Switch that provides the seamless network connection These PoE ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs) In this situation, the electrical power is transmitted along with data in one single Cable Allowing you to expand your network where there are no power lines or outlets here you wish to fix devices such as Aps IP Cameras or IP Phones, etc VLAN isolation to meet security monitoring requirements Support extension technology Data transmission and Power Supply up to 250m Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed. TXE188 is easy to install and use. It requires no configuration and installation With desktop design, outstanding performance and quality The 10-Port 10/100Mbps Desktop PoE switch is a great selection for expanding your home or office network Features Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3x,IEEE802.3az,IEEE802.1q Ethernet standards; Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE port, all power up to 117W VLAN isolation to meet security monitoring requirements Support 10 x10/100Mbps Auto-negotiation RJ45 ports with 8 port PoE function (POE1-8); Support extension technology, up to 250m transmission distance Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode and backpressure for Half-duplex Mode LED indicators for monitoring Port Link / Activity Internal power supply, exquisite design, suitable for desktop use b'/xc2/xa0'

M-Link 8 PORT 10/100 POE+2 PORT Switch 8PORT 10/100 POE+2PORT – TXE188 8-Ports 10/100Mbps PoE + 2-Ports 10/100Mbps Unmanaged Ethernet Switch Description TXE188 is a 10-port 10/100Mbps Desktop PoE Switch that provides the seamless network connection These PoE ports can automatically detect and supply power with those IEEE 802.3at compliant Powered Devices (PDs) In this situation, the electrical power is transmitted along with data in one single Cable Allowing you to expand your network where there are no power lines or outlets here you wish to fix devices such as Aps IP Cameras or IP Phones, etc VLAN isolation to meet security monitoring requirements Support extension technology Data transmission and Power Supply up to 250m Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed. TXE188 is easy to install and use. It requires no configuration and installation With desktop design, outstanding performance and quality The 10-Port 10/100Mbps Desktop PoE switch is a great selection for expanding your home or office network Features Comply with IEEE802.3, IEEE802.3i,IEEE 802.3u,IEEE802.3x,IEEE802.3az,IEEE802.1q Ethernet standards; Supports IEEE802.3af, IEEE802.3at PoE standards Supports PoE power up to 30W for each PoE port, all power up to 117W VLAN isolation to meet security monitoring requirements Support 10 x10/100Mbps Auto-negotiation RJ45 ports with 8 port PoE function (POE1-8); Support extension technology, up to 250m transmission distance Independent Uplink Port can ensure that the Port can easily cope with sudden high traffic And ensure that the upstream channel is unobstructed Supports IEEE802.3x flow control for Full Half-duplex Mode and backpressure for Half-duplex Mode LED indicators for monitoring Port Link / Activity Internal power supply, exquisite design, suitable for desktop use b'/xc2/xa0'

Intellinet PoE+ Tester - Power over Ethernet Plus Test Tool; Detects Endspan, Midspan, IEEE802.3af- and IEEE802.3at, Retail Box, 2 year Limited Warranty. Product Overview: The Intellinet PoE+ Tester is a Power over Ethernet detector that confirms 802.3af and 802.3at connections. It also identifies the existence and type of Power Sourcing Equipment (either Endspan or Midspan). This tester is a simple plug-and-play tool that allows the installer to correctly identify PoE or PoE+ without the risk of damaging expensive equipment. Features: • Detects IEEE802.3af and IEEE802.3at • Tests for both Endspan and Midspan power • Compact design Specifications: • Product Code: 780131 • Description: Intellinet PoE+ Tester - Power over Ethernet Plus General • Detection of IEEE802.3af and IEEE802.3at • Detection of PSE (power sourcing equipment) type • Plug and Play • Simple and effective Dimensions • 27.94 (L) x 33.02 (W) x 68.58 (H) [mm] o (L) x 1.3 (W) x 2.7 (H) [in] Package Contents • PoE+ Tester • 1 x 10 cm (3.94 in.) RJ45 to RJ45 cable • Instruction manual

The Cudy PE25 2.5Gbps PCI Express Network Adapter is a great way to expand your Desktop PCs network options. It features a high-speed Ethernet port that supports 2.5Gbps speeds over a standard Cat5e or higher cables at distances up to 100m. Whether you use a personal PC or a hosting server, this network adapter gives you the performance you need to get the job done. Its PCI Express 1x slot makes it simple and easy to install on any motherboard that supports PCI-E x1. FEATURES: IEEE802.3bt/IEEE802.3at/IEEE802.3af compliant IP67 waterproof enclosure for outdoor use One gigabit PoE input port and Two-gigabit output PoE ports Extend additional 100 meters for PoE Network Wall-Mount design for any application scenario Plug and play, no additional power supply required SPECIFICATIONS: Chipset: RTL8125 Standards: IEEE 802.3 / IEEE 802.3u / IEEE 802.3ab / IEEE 802.3az / IEEE 802.3bz Network media: 10Base-T,cat3 or above UTP,1000Base-Tx,cat5 or above UTP Data rate: 10/100/1G/2.5Gbps Interface: PCI Express 1x slot Auto MDIX: YES Full Duplex Support: YES MTBF: 376,212 Hours LED Indicator: Link/Act, Speed Port number: 1 x RJ45 Support OS: Windows®10(32/64), Win7 (32/64), Win8,8.1 (32/64) Windows Server® 2012, 2008 LINUX up to 4.15 Product Dimensions: 7.2 x 5 x 0.2 cm WHAT’S IN THE BOX: Cudy PE25 2.5Gbps PCI Express Network Adapter – Black/Red x1

Intellinet 16-Port Gigabit PoE+ Switch, 220 Watt Power Budget, Rackmount, IEEE 802.3at/af Power over Ethernet (PoE+/PoE) Compliant, Endspan, Retail Box, 2 year Limited Warranty

Tenda TEF1126P-24-250W Rackmount Switch TEF1126P-24-250W is an unmanaged Network PoE switch independently designed by Tenda. Compliant with IEEE802.3af and IEEE 802.3at standards, it can identify PoE-powered devices intelligently. With a maximum PoE power output of 230 W and 30 W for a single port, it can supply power when transmitting data with APs, IP cameras, and IP phones. The Tenda Network Switch supports 4 working modes, including standard, priority, extend, and VLAN modes, an ideal choice for SMBs, hotels, schools, and factories with video surveillance and wireless networking requirements. GE and SFP Uplink Ports Flexible Networking With Less Breakdown It provides 24*FE+2*GE/1SFP. The 1-24 ports support AF/AT standard PoE power supply mode, which can intelligently identify the power receiving equipment. The Gigabit uplink port can be used for short-distance networking. With one 1000 Mbps combo SFP slot, the Tenda Network Switch can meet the current demand for uplink bandwidth of Gigabit WLAN and HD digital surveillance. Working with Tenda optical fibre module TEG311SM, the switch supports a maximum transmission distance of up to 20km. 4M Large Buffer Guarantees The Surveillance Transmission Stable And Smooth The product has a 4M buffer, which is twice larger than the similars. The maximum output of a single port is 30W, and the whole device is 250W. When used alone, it can provide data transmission and power for 24 PoE IP cameras, APs, etc. Extraordinary quality, favoured by engineering. 6KV Excellent Lightning Protection The switch offers various safety and protection types, including 6 KV lighting protection, PSE short-circuits protection, PoE overload protection, surge current protection etc, and these greatly protect the switch from being damaged by an inductive thunderstorm. Besides, it supports wide voltage input, AC：100-240V~50/60Hz. 230W High Power Output, Diversified Applications Providing 24 100M PoE ports in accordance with the IEEE802.3AF / AT standard, the maximum PoE output of the whole machine is 230W, and of a single port is 30W. Not afraid of burst traffic, avoid power failure b'&' restart, and it can provide stable power supply and data transmission for HD PoE IP cameras, APs, etc. 4 Modes For More Scenarios, One-key To Change Smart And Easy Standard mode, Port-based Priority mode, Port-based VLAN mode and Extend mode make TEF1126P-24-250W be able to deal with different networks, special for small b'&' Medium-sized IP Surveillance b'&' WI-FI coverage project. Up To 250 Meters Long Distance Transmission Under The Extend Mode, Beyond Hundred Meters Transfer Limitation Due to the complex monitoring environment, the distance from each terminal to the monitoring centre is different, some even more than a hundred meters. TEF1126P series can support 250 meters of data transmission in the Extend mode, which can save the cost of your project with fewer devices used. Specifications Standard b'&' Protocol IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE802.3z, IEEE802.3x, IEEE802.3af/at LED 24 * Link/Act LEDs 1 * G1 LED 1 * G2/SFP2 LED 1 * PoE-MAX LED 1 * Power LED Interface 24 * 10/100 Mbps Base-TX RJ45 ports (Data/Power) 1 * 10/100/1000 Mbps Base-T RJ45 ports (Data) 1 * 1000 Mbps Base-X SFP port (Combo) Forwarding Rate 6.55 Mpps Switching Capacity 8.8 Gbps MAC Address Table 16K Lightning Protection ≥6KV Input Voltage AC: 100-240V~50/60Hz PoE Supply Ports 1-24 support standard IEEE802.3af/at 30W output per PoE port 230W output of the total PoE Power Power Consumption 50W output the whole device Dimension 440*178.8*44mm Four Modes Standard: Default mode of the switch. In this mode, it works as an unmanaged switch all ports can communicate with each other separately. Priority: In this mode, port G1 and G2/SFP2 serve as uplink ports, ports 1 – 8 serve as high priority ports. All ports can communicate with each other separately. Extend: In this mode, the data rate of ports 17 – 24 reduces to 10 Mbps, the maximum transmission distance can be 250 meters, and all ports can communicate with each other. VLAN: In this mode, ports 1 – 24 of the switch can communicate with port G1, G2/SFP2 separately, but cannot communicate with each other. You can enable this mode to reduce broadcast storms and isolate DHCP broadcasts. Environment Operating Temperature: 0℃~45℃ (32℉~113℉) Storage Temperature: -40℃~70℃ (-40℉~158℉) Operating Humidity: 10%~90% non-condensing Storage Humidity: 5%~90% non-condensing Certification CCC、FCC、CE、RoHS