Transmission methods

This TT685N camera flash applies to Nikon cameras and is compatible with I-TTL II autoflash. With this I-TTL II compatible flash, your shooting will become simpler.Suitable for Nikon DSLR Camera D800 D700 D7100 D7000 D5200 D5100 D5000 D300 D300S D3200 D3100 D3000 D200 D70S D810 D610 D90 With 2.4G wireless transmission, X1N (for Canon) can be used to trigger camera flash, studio flash and camera shutter over 100 meters distance Support for I-TTL II autoflash, 1/8000 high-speed sync, flash exposure compensation, flash exposure lock, modeling flash, etc Two Transmitting Styles to Offer Creative Light Effect,Optic transmission with even illumination and stable output,2.4G wireless transmission with all-in-one functions and 100 meters further transmission.Convenient Dot-matrix LCD panel,With dot-matrix LCD panel to offer clear and easy operation Xpro-N:Built-in Godox 2.4G Wireless X System & Versatile Using Methods:As a wireless Godox Flash Trigger/ wireless Shutter Release Trigger/ wireless Nikon Speedlights Trigger/ Flash Trigger with 2.5mm Sync Cord Jack

5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

3Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 3 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

Product Specification POWER. Guide No. (ISO100).meters 43 (105mm). ZOOM. Zoom head Yes focal length coverage 24-105mm Coverage with wide panel 14mm Auto zoom for sensor size Yes. FLASH MODES. Auto exposure control E-TTLII/E-TTL High speed sync (FP) Yes Manual / output settings Yes - 1/1- 1/128 Manual steps 1/3 step. FLASH-RELATED FUNCTION. FE lock Yes Flash exposure compensation Yes Flash Exposure bracketing No Second-curtain flash sync Yes Modelling flash Yes Colour temperature info communication Yes. WIRELESS FLASH. Transmitter Yes Transmission type Radio Signal range (Infra-red/Radio) Indoors: 12-15m / 30m Outdoors: 8-10m / 30m Slave function Infra-red/Radio Master function Radio No of groups (Optical/Radio) - / 5 No of channels (Optical/Radio) - / 15 Remote Shutter Release Yes. FLASH HEAD MOVEMENT. Up 45, 60, 75 and 90° Left 60, 75, 90, 120, and 150° Right 60, 75, 90, 120, 150 and 180 °. AF ASSIST. AF-assist beam Yes Number of AF points supported 1 AF-assist beam type Infra-red / flash strobe. POWER SOURCE. Battery 4 x AA batteries Minimum recycling time * Approx. 3.5 sec External power supply No. CONSTRUCTION. Dust and water resistance No Mounting foot material Metal. MISC.. Custom function 10 (8 personal functions) Flash settings from camera menus ** Yes External flash exposure sensor No PC terminal No Compatible Accessories Off-camera shoe cord OC-E3 Bounce adapter SBA-E2 Color filter/Bounce adapter holder Color filter SCF-E2 Dedicated flash bracket No. DIMENSIONS & WEIGHT. Size (W x H x D), mm 70.5 x 113.8 x 98.2 Weight (Excluding batteries), grams 295g Working temperature range 0 °C - 45 °C / 32 °F - 113 °F Working humidity 85 % or less. All data is based on Canon standard testing methods (according to CIPA Standards) except where indicated. Subject to change without notice. * time taken to recharge flash after full discharge using Alkaline AA batteries ** With compatible cameras only..

Description: AM2320 digital temperature and humidity sensor is a kind of temperature and humidity complex sensor with calibrated digital signal output. The sensor includes a capacitive humidity sensing element and a high-precision integrated temperature measuring element, and is connected with a high-performance microprocessor. The product has excellent quality, ultra fast response, anti-interference ability, cost-effective and so on. AM2320 communication mode adopts single bus, standard I2C two communication methods. The two modes of communication can be freely switched, the user is free to choose, easy to use, wide range of applications. Application range: HVAC, dehumidifier, testing and testing equipment, consumer goods, automotive, automatic control, data recorder, weather station, home appliances, medical and other related humidity control, humidity measurement and control. Product highlights: Fully interchangeable, low cost, long-term stability, relative humidity and temperature measurement, long distance signal transmission, digital signal output, accurate calibration, low power consumption, single bus digital interface standard, I2C standard bus digital interface, communication mode can be free to choose. Technical parameter: Measuring range Temperature range: -40 - +80￢ﾄﾃ, humidity range: 0-99.9%RH Accuracy (25￢ﾄﾃ environment) Temperature accurate value: ±0.5￢ﾄﾃ, humidity accurate value: ±3%RH (10...90%RH) Resolving power Temperature: 0.1￢ﾄﾃ, humidity: 0.1%RH Attenuation value Temperature: 0.1￢ﾄﾃ / year, humidity: Sensor type Temperature: resistance type sensor, humidity: capacitive sensor Response time Temperature: 5s, humidity: 5s 1/e (63%) Operating temperature range: -40 - +80￢ﾄﾃ Power source: DC 3.1-5.5V Output signal: single bus /I2C signal Shell material: PC plastic Dimension: 15 x 12.1 x 4.5mm Package included: 3 x Temperature and humidity sensor

*Fully Support TTL Autoflash, 1/8000s High-Speed Sync, Multi Flash, Manual Flash, Flash Exposure Compensation, TCM Transform Function, Magnfication Function, One-Shoot & Multi- Shoot Setting, Group Modeling Lamp Control, Group Zooming, Adjusting All Groups' Output Value Simultaneously, etc *Add 01 to 99 Wireless ID settings,Which Can Only Achieve Triggering When the channels and Wireless IDs of the Master and Slave Unit are Set to the Same,Avoiding Signal interference effectively *11 Customizable Functions,Extra-large LCD panel, 5 group buttons and 4 function buttons offer convenient manipulation *Built-in Godox 2.4G Wireless X System & Versatile Using Methods:e.g. As a wireless Godox Trigger for camera flash,outdoor flash and studio flash; As a Wireless Speedlites Trigger;As a Wireless Shutter release Trigger;As a flash(without Godox X system) trigger with 2.5mm Sync Cord Jack *Godox XPro-S High Speed Sync Flash Transmitter is compatible camera: Sony series cameras (TTL autoflash) Support for the cameras that have PC sync socket More Feautures FE lock 11 Customizable Functions Manual Flash 1/1 - 1/256 Power Modeling Light Status Control Adjusts the Flash Zoom Coverage for Each Group Selective Transmission of Data Conserves Energy and Battery Life Magnification Function Displays Details of Each Group Settings Global Adjustments to Exposure Values for Multi-Group in M Mode 5 Group Buttons and 4 Function Buttons Offer Convenient Manipulation Support Type-C USB Firmware Upgrade and Wireless Triggering by 2.5mm Sync Cord Jack Compatible Camera: Sony series cameras (TTL autoflash) Support for the cameras that have PC sync socket Flash Exposure Control TTL Autoflash: Sony Manual flash mode: Yes Multi (Stroboscopic) flash mode: Yes Function HSS (High-speed sync): Yes Second-Curtain Sync: Yes Flash exposure compensation: Yes,3 Stops in 1/3 stop increments Flash exposure lock: Yes Auto Focus Assist: Yes Modeling Lamp Control: Control the modeling lamp by the flash trigger Beeper: Control the sound of the flash trigger Wireless Setting: The receiver end can control the camera shooting through the 2.5mm sync cord jack ZOOM setting: Adjust the ZOOM coverage value from the transmitter TCM function: Transforms the TTL shooting value into the output value in M mode Firmware upgrade: Upgrade through the Type-C USB port Memory function: Settings will be stored 2 seconds after last operation and recover after a restart Wireless Flash Wireless Signal Range: >328 feet / >100 Meters Remote System: 2.4GHz Modulation Mode: MSK Channels: 32 Wireless ID: 01-99 Groups: 16 Dimensions: 3.5x2.3x2.0"/ 90x58x50mm Display: Large LCD panel with customizable backlight PACKAGE CONTENTS: 1* Godox Xpro-S 1* Product Manual 1* CONXTRUE USB LED Free Gift