Transmission 85

Introduction:   What is ESP8285? ESP8285=ESP8266+1M Flash application temperature up to 125℃! First and  foremost the code programmed in ESP8266 could be used for ESP8295 intact.   ESP-M2 module core processor is the high-performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated an advanced Tensilica's L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi function, which can be used independently and also used as a slave with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is a benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design.   Features: Ultra- small size; Support serial to WiFi; Wireless transparent transmission; Long distance transmission with ultra-low power; Support outboard antenna; Bearing high temperature to 125 ℃, compared to the 85℃ for ESP8266.   Specifications:   SOC characteristics Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS; Built-in TCP/IP protocol; Built-in one-channel 10-bit high precision ADC; Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO; Deep sleep current is 10uA, the cut-off current is smaller than 5uA; Wake, connect and transmission data package within 2ms; The consumer power is smaller 1.0Mw (DTIM3) when at standby status; Built-in 1M byte for SPI Flash.   WiFi characteristics Support 802.11 b/g/n/e/I; Support Station, Soft AP, Soft AP+STA mode; Support WiFi Direct (P2P); Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration. P2P finding, P2P GO mode/ GC mode and P2P power manage WPA/PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4GHz); 802.1h/RFC1042 frame encapsulation; Support seam less roaming; Support AT remote update and cloud update (OTA); Support Smart Config function (including Android and Ios device).   Module interface:   2* UART; 1*ADC; 1*En; 1*wakeup pin; 1*HSPI; 1*I2C; 1*I2S More than 10*GPIOs Working temperature: -40℃-+125℃; Module size: 12.3*20mm   Applications:   Electrical appliance; Smart power plug, smart light; Infant monitor; Sensor networks; Security ID label; Wireless location beacon; Home automation; Mesh networks; IP video camera; Wearable electronics; Wireless location recognition; Industrial wireless control;   Package included:   1 x Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module

Introduction: What is ESP8285? ESP8285=ESP8266+1M Flash application temperature up to 125￢ﾄﾃ! First and foremost the code programmed in ESP8266 could be used for ESP8295 intact. ESP-M2 module core processor is the high-performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated an advanced Tensilica’s L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi function, which can be used independently and also used as a slave with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is a benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design. Features: Ultra- small size; Support serial to WiFi; Wireless transparent transmission; Long distance transmission with ultra-low power; Support outboard antenna; Bearing high temperature to 125 ￢ﾄﾃ, compared to the 85￢ﾄﾃ for ESP8266. Specifications: SOC characteristics Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS; Built-in TCP/IP protocol; Built-in one-channel 10-bit high precision ADC; Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO; Deep sleep current is 10uA, the cut-off current is smaller than 5uA; Wake, connect and transmission data package within 2ms; The consumer power is smaller 1.0Mw (DTIM3) when at standby status; Built-in 1M byte for SPI Flash. WiFi characteristics Support 802.11 b/g/n/e/I; Support Station, Soft AP, Soft AP+STA mode; Support WiFi Direct (P2P); Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration. P2P finding, P2P GO mode/ GC mode and P2P power manage WPA/PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4GHz); 802.1h/RFC1042 frame encapsulation; Support seamless roaming; Support AT remote update and cloud update (OTA); Support Smart Config function (including Android and Ios device). Module interface: 2* UART; 1*ADC; 1*En; 1*wakeup pin; 1*HSPI; 1*I2C; 1*I2S More than 10*GPIOs Working temperature: -40￢ﾄﾃ-+125￢ﾄﾃ; Module size: 12.3*20mm Applications: Electrical appliance; Smart power plug, smart light; Infant monitor; Sensor networks; Security ID label; Wireless location beacon; Home automation; Mesh networks; IP video camera; Wearable electronics; Wireless location recognition; Industrial wireless control; Package included: 3 x Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module

Introduction: What is ESP8285? ESP8285=ESP8266+1M Flash application temperature up to 125?? First and foremost the code programmed in ESP8266 could be used for ESP8295 intact. ESP-M2 module core processor is the high-performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated an advanced Tensilica’s L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi function, which can be used independently and also used as a slave with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is a benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design. Features: Ultra- small size; Support serial to WiFi; Wireless transparent transmission; Long distance transmission with ultra-low power; Support outboard antenna; Bearing high temperature to 125 ?? compared to the 85??for ESP8266. Specifications: SOC characteristics Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS; Built-in TCP/IP protocol; Built-in one-channel 10-bit high precision ADC; Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO; Deep sleep current is 10uA, the cut-off current is smaller than 5uA; Wake, connect and transmission data package within 2ms; The consumer power is smaller 1.0Mw (DTIM3) when at standby status; Built-in 1M byte for SPI Flash. WiFi characteristics Support 802.11 b/g/n/e/I; Support Station, Soft AP, Soft AP+STA mode; Support WiFi Direct (P2P); Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration. P2P finding, P2P GO mode/ GC mode and P2P power manage WPA/PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4GHz); 802.1h/RFC1042 frame encapsulation; Support seamless roaming; Support AT remote update and cloud update (OTA); Support Smart Config function (including Android and Ios device). Module interface: 2* UART; 1*ADC; 1*En; 1*wakeup pin; 1*HSPI; 1*I2C; 1*I2S More than 10*GPIOs Working temperature: -40??+125?? Module size: 12.3*20mm Applications: Electrical appliance; Smart power plug, smart light; Infant monitor; Sensor networks; Security ID label; Wireless location beacon; Home automation; Mesh networks; IP video camera; Wearable electronics; Wireless location recognition; Industrial wireless control; Package included: 3 x Mini ESP-M2 ESP8285 Serial Wireless WiFi Transmission Module

Introduction: What is ESP8285? ESP8285=ESP8266+1M Flash application temperature up to 125?? First and foremost the code programmed in ESP8266 could be used for ESP8295 intact. ESP-M2 module core processor is the high-performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated an advanced Tensilica’s L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi function, which can be used independently and also used as a slave with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is a benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design. Features: Ultra- small size; Support serial to WiFi; Wireless transparent transmission; Long distance transmission with ultra-low power; Support outboard antenna; Bearing high temperature to 125 ?? compared to the 85??for ESP8266. Specifications: SOC characteristics Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz and RTOS; Built-in TCP/IP protocol; Built-in one-channel 10-bit high precision ADC; Outboard interface: HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO; Deep sleep current is 10uA, the cut-off current is smaller than 5uA;

Category: Aerial antenna connector cable // Connection type: Aerial // Antenna connector A: aerial cable (TV connector, straight) // Connector B: aerial cable (TV connector, straight) // Shielding: 100 dB // Insulation: braided and film shielding // Connector-type: straight // Characteristics: gold-plated contacts // Cable application: TV aerials / antennas // Version: connector cable // Cable shape: round // Internal conductor material: copper // Colour: Black // Cable length: 3m (9.85 ft.) deleyCON PREMIUM HDTV / HD TV aerial cable // compatible with all devices with TV aerial / antenna connector (Coaxial cable e.g.: receivers, set-top boxes, TVs, radio and DVB-T, DVB-S, DVB-C and many more) For connecting your TV or other compatible device with the wall or cable connector // optimised for superb picture and sound quality // HD-TV broadcasts with exceptional sharpness // fitted, particularly conductive, gold-plated metal TV aerial cable // full 4K / UltraHD / 1080p / FullHD / HDTV support Analog and digital television signals in excellent quality // high quality copper optical fibre cable / high density, multi-layered shielding to prevent interference // excellent, lossless transmission, signal quality and durability // versatile premium cable - easily installed The cable was radically redesigned in order to perfect its durability, stability and accuracy of fit // Shielding capability: 100dB / Resistance 75Ohm // Shielded connectors made entirely from metal ensure a perfect transition through the shielding

Features: The use of specially designed PCB circuit board. Electrical characteristics are very good, strong performance With better cooling effect of thermal grease. Use high power transistor, product safety and reliability without electric shock hazard PCB size: 85 x 54mm Installation of video connection, the actual installation of only 3~5 minutes: (http://v.youku.com/v_show/id_XMTYzMTcwMjc0NA==.html?from=s7.8-1.2& x) Note: Pay attention to protect the secondary coil during installation, the secondary coil for enameled wire is very fine, so don't hurt or broken wire General secondary coil is the final installation of the power detection after the successful use of glue to fix it on the PCB board. Primary coil to one end of the soldering on the right side of the circuit board "L1" soldering plate and counter clockwise to the other end of the two lap welded to the left "L1" pads, attention is counter clockwise rather than clockwise, if the direction is  reverse, the machine will not work. Unauthorized modification of power interface, if the polarity reversed, it will burn out the triode, remember. Package includes: 1 x PCB 1 x Switch 4 x Screws 1 x Heat sink 1 x Triode 1 x Screw to fi x triode 1 x Resistance 1 x Capacity 1 x Diode 1 x Primary coil 1 x Secondary coil Test pictures, for reference only!  

Overview: What is ESP8285? ESP8285=ESP8266+1M Flash, the bearing high temperature is 125??(the one for ESP8266 is just 85??. More important, the code programmed in ESP8266 can be used for ESP8285 intactly. ESP-M3 is encapsulated by the high performance chip ESP8285, which is equal to ESP8266 chip plus 1M Flash. The chip ESP825 is encapsulated a advanced Tensilica’s L106 32-bit CPU, together with SRAM. ESP825 has the full and complete WiFi fuction, which can used independently and alsoused as a slaver with other Hoster MCU, which can start directly from the out-built Flash. In addition, the built-in high-speed buffer is benefit for the system performance. Especially, ESP8285 can be used as a WiFi adapter by SPI/SDIO and/or I2C/UART interface, when it is applied to the other MCU design. Features: Ultra-small size; Support serial to WiFi; Wireless transparent transmission; Long distance transmission with ultra-low power; Bearing high temperature to 125 ?? compared to the 85??for ESP8266. Specification: https://github.com/SmartArduino/SZDOITWiKi/wiki SOC characteristics: Built-in Tensilica L106 ultra-low power 32-bit CPU, main frequency supports 80MHz and160MHz, and RTOS; Built-in TCP/IP protocol; Built-in one-channel 10-bit high precision ADC; Outboard interface: HSPI, UART, I2C, I2S, IR Remote Controk, PWM, GPIO; Deep sleep current is 10uA, the cut-off current is smaller than 5uA; Wake,connect and transmission data package within 2ms; The consume power is smaller 1.0Mw (DTIM3) when at stand by status; Built in 1M byte for SPI Flash. WiFi characteristics: Support 802.11 b/g/n/e/I; Support Station, Soft AP, Soft AP+STA mode; Support WiFi Direct (P2P); Support CCMP (CBC-MAC, computation mode), TKIP (MIC, RC4), WAPI (SMS4), WEP (RC4), CRC etc., for hardware acceleration. P2P finding, P2P GO mode/ GC mode and P2P power manage WPA/PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4GHz); 802.1h/RFC1042 frame encapsulation; Support seam less roaming; Support AT remote update and cloud update (OTA); Support Smart Config function (including Android and Ios device). Module interface: 2* UART; 1*ADC; 1*En; 1*wakeup pin; 1*HSPI; 1*I2C; 1*I2S More than 10*GPIOs Working temperature: -40??+125?? Module size: 26.8mm*16mm Electronical appliance: Smart power plug, smart light; Infant monitor; Sensor networks; Security ID label; Wireless location beacon; Home automation; Mesh networks; IP video camera; Wearable electronics; Wireless location recognition; Industrial wireless control; Package included: 1 x ESP-M3 Wireless WiFi Transmission Module

- Wireless monitoring kit and AV transmission system - With frequency switching key, can switch between 12 frequencies; - LED screen will automatically display frequency once power on; - Interface: 12V power adapter, video, audio. Transmitter parameters: Transmitting power: 2.5W Transmitting frequency: 1080/1120/1160/1200/1240/1280/1320/1360 (MHz) Frequency control: Digital frequency phase-locked loop control Signal transmission: Video and audio synchronous transmission Straight-line transmission distance: 1000~2000m Voltage: DC +12V Current: 3000mA Receiver parameters: Modulation type: FM Receiving frequency: 0.9~1.2GHz Signal receiving: Video and audio synchronous transmission Receiving sensitivity: -85dBm Video input level: 1Vp-p Audio input level: 1Vp-p Working temperature: -20~+50°C / -4~+122°H Working humidity: 85%RH Storage temperature: -40~+80°C / -40~+185°H Voltage: DC +12V Current: 500mA Application: Household, office, warehouse, hospital, school, supermarket, hotel, farm, etc General Form Color Silver + Black + Multi-Colored Material Aluminum Quantity 1 set Dimensions & Weight Dimensions 5.16 in x 3.15 in x 0.83 in (13.1 cm x 8 cm x 2.1 cm) Weight 7.97 oz (226 g) Packing List 1 x Transmitter 1 x Receiver (10+/-2cm-cable) 2 x Antennas 2 x Audio cables (120+/-2cm) 1 x 4-plug cable (21+/-2cm) 2 x BNC adapters 1 x Connecting cable (10+/-2cm) 1 x US plug 100~240V charger (US plug wire length: 50+/-2cm, DC wire length: 94+/-2cm) 1 x US plug 100~240V charger (wire length: 94+/-2cm) 1 x Chinese & English user manual

SIM808 GSM GPRS GPS BT Development Board Module For Arduino Description: SIM808 a new generation of GSM, GPRS, GPS, bluetooth (optional) SIM808 GSM GPRS module is a four frequency for the castle hole encapsulation. Its performance is stable, compact appearance, high cost performance, which can meet the various needs of customers. SIM808: SIM808 working frequency for GSM/GPRS / 1800/1900 850/900 MHZ, can realize low-power transmission of voice, SMS and data information. Features: The four frequency MHZ 850/900/850/900 SMS FTP/HTTP, embedded TCP/UDP protocol DTMF detection, bluetooth 3.0 (optional), USB interface Arduino SIM808 shields hardware: Power interface support 5-20V voltage input, pay attention to the voltage of 5-9V, can provide not less than 2 a power adapter current. 1. Can choose to use through the jumper cap hardware serial port (D0 D1) or software serial port (D7 D8). 2. Support the MICRO SIMCARD. 3. Support four headphone jack (I type). 4. Update SIM800C firmware support via USB or serial port. 5. Can be upgraded to a bluetooth version of the development board. 6. On board TVS diode, SIM card protection IC, two 100 uf tantalum capacitors and so on a variety of ways to make the stable development board performance. 7. Support the lithium battery (3.6-4.2 V) For TTL level serial communication interface. Fully compatible with the Arduino and compatible with other 5 V, 3.3 V, 2.85 V system. Arduino SIM808 shields software: By TTL level a serial port communication with external systems, the default is communicated with 5 v system directly. Communicated 3.3 V and 2.85 V, it needs to do a bit of hardware processing. Communication interface (command) for the AT command, which is control module function to realize the AT command, such as: control module to make calls using ATD * * * * * * *; (* phone number) for each other. Package included: 1 x SIM808 GSM GPRS GPS BT Development Board Module For Arduino

SIM800L GPRS GSM Module Micro SIM Card Core Board Quad-band TTL Port for Arduino Use this GSM/GPRS to create a remote data link. Use our GlueStick antenna for better reception in remote locations. The antenna plugs into the module. Comes with a basic antenna that you can solder onto the module. Glue Stick Antenna is also available.  Feature Implementation Supply Voltage 3.4 - 4.4V Power Saving Sleep mode 0.7mA (AT+CFUN=0) Frequency Bands Quad-Band: GSM850, EGSM900, DCS1800, PCS1900 Transmitting Power Class 4 (2W) at GSM850, EGSM900 Class 1 (1W) at DCS1800, PCS1900 GPRS Connectivity GPRS Multi-Slot Class 12 (Default) GPRS Multi-Slot Class 1-12 (Option) Temperature Range -40 to +85 Degrees Celsius Storage Temperature -45 to +90 Degrees Celsius Data GPRS GPRS Data down-link transfer max: 85.6 kbps GPRS Data up-link transfer max: 85.6 kbps Coding Scheme: CS-1, CS-2, CS-3 and CS-4 PAP Protocol for PPP connect Integrate TCP/IP Protocol Support Packet Broadcast Control Channel (PBCCH) CSD Transmission Rates: 2.4, 4.8, 9.6, 14.4 kbps     This item is available in stock and is not drop shipped. This avoids delays, customs charges and extra VAT.

At a Glance... 3 lines of defense including IP camera, PIR motion detection sensor and door sensor Wi-Fi Security System makes for easy installation and setup Remote notifications and snapshots direct to you iOS or Android Smartphone Pan and tilt night vision IP camera for great area coverage night and day Take your home security to the next level with this Wireless home security system coming with IP camera, PIR motion detection, door / window alarm with Mobile phone support HOME SECURITY SYSTEM This wireless home security system has 3 levels of protection for your home or workplace. With a quick and simple setup you just downloads the associates Android or iOS app by scanning the QR code and follow the simple screen prompts to activate the system. The jewel in this security system is the 720P IP camera, not only does it work as a controller relating messages for the PIR and door sensor but it provides state of the art surveillance in your home of office. With pan and tilt functions the IP camera can cover a large area performing the same job as several static cameras. Its 1/3 inch CMOS sensor brings pin sharp images at HD resolutions and with 4 motion detection zones it will notify you of any intruders detected. WI-FI SECURITY SYSTEM Wi-Fi technology means its easy to connect to your network from anywhere in the home freeing up placement restrictions. Support for both Android and iOS devices let you receive alarm notifications in the form of snapshots directly on your smart phone no matter what OS preference you have. Your first line of defense are entry points and that's why this modern home security system comes with a wireless door sensor. This will monitor any entry points and trigger an alert if they are disturbed by sending a wireless message to the IP camera that in turn can notify your phone via over your home network. A PIR sensor is also present in this home security setup. This is great for covering hallways or entrances and when activate you will be notified via the systems Smartphone app. With 3 lines of defense you can keep your home or office secure night and day bring you peace of mind that your loved ones and valuables are being watched over, even if you're not onsite yourself. Manufacturer Specifications General CPU: Industrial-grade embedded micro controller Hi3518E Operating System: Embedded LINUX operating system Onvif 2.0 Support Mobile Phone Access: Android, iPhone, Windows mobile IP mode: Dynamic IP address, static IP address, Supporting WPS (Wi-Fi Protected Setup) Client do not need to know the SSID and security keys or pass phrases when connecting WPS-enabled devices Video Compression Format: H.264 Video Resolution: VGA 640x480 (25 fps), 720p 1280x720(15pfs) Resolution: 720P (1280x720) Image Adjustment: Brightness, Contrast, Saturation, Sharpness, Exposure Image sensor: 1/3 Color 1MP CMOS Frame Rate: 1 to 25 fps Video Standard: PAL, NTSC Dual way Audio: Two way audio Memory: Up to 128 GB Lens: F1.2 LUX: 0.1LUX SNR: 48dB Audio Compression Format: G.711 Input: Built-in Microphone, 38dB Output: Build-in Speaker, 8 Ohm, 2x 1W Speaker PTZ Motor: Built-in motor Rotation Angle: Horizontal: 360 Degrees, Vertical: 85 Degrees Night Vision Filter switch: IR cut filter auto-switch automatically Night Vision: 11 PCS IR LED lights IR Distance: Up to 10 Meters Alarm Alarm: Motion Detection Detection Area: Support 4 Detection Areas Alarm Notification: Email Snapshot Notification, FTP Snapshot Upload, Event record to Micro SD Card Door / Window Sensor Distance: From main unit, Up to 200 FT Only the main unit (HSA100) will sound, when the alarm is triggered 433 MHz Transmission Distance with the IP camera: Up to 20 meters (No obstacle) Battery Life: Up to 1 year Battery Power: 23A 12V Alkaine Battery PIR Detection Alarm Transmission distance with the IP camera:20 meters (No obstacle) Battery Power: 6F22 9V Battery 3x 1.5V AM4 Battery Life: About 2 year Detecting Distance: 12 m

4 Channels 2.4G Wireless USB Video Receiver DVR for PC & Laptop CCTV Colour Recorder Key Features: 2.4G Wireless Pinhole Camera Easy to Install or Hide Built-in Microphone For Audio Monitoring & Lithium Battery Lasts For 1.5-2.5 Hours USB Wireless Receiver to Connect to Your PC or Laptop, Easy to View and Record On HDD Specification (Camera): High Quality 2.4GHZ wireless high quality color CMOS camera for clear images 4 channel operation allows multiple (1-4) camera systems The camera is made by pinhole lens Depends on various condition,  Up to 40 meters outdoor range and up to 15 meters indoor range  Metal housing with adjustable focus lens Easy to install on wall or ceiling Frequency ISM 2,400 - 2,483MHz Imaging Sensor 1/3 inch OMNIVISION Color CMOS Horizontal Resolution 380TV Line CMOS Pixels PAL: 628 x 582; NTSC: 510 x 492 Viewing Angle: 62 degrees Minimum Illumination: 1. 0Lux / F1.5 Transmission Power: 10mW Consumption Current: 8mA Modulation Mode: FM Bandwidth: 18M Operating Range: 10m~60m Power Supply: DC 8V or Built-in Lithium battery Operating Temperature: -10 ~ +40 celsius degree Operating Humidity: 85%RH Size (LxWxH): 7.2cm x 2.2cm x 6.5cm Net Weight: 72g Specification (Receiver): Wireless USB DVR. 4-channel 2.4GHz wireless video/audio. Capture images 30 frames per second. Record file format AVI and play with Windows Media Player. USB 2.0 interface,transmission rate up to 480Mpit/s,48times. Fluency video display,720*576 image up to 30 frames/s. Moving image display upto 1440*1152 Sharp and nature image with true color. Advanced digital video control function Receiving Frequency: channel 1: 2.414GHZ channel 2: 2.432GHZ channel 3: 2.450GHZ channel 4: 2.468GHZ System Requirement:  Window XP, VISTA32, WINDOWS 7 1.7GHz CPU or better 128M memory or better Microsoft DirectX 9.0C USB2.0 Interface Audio Card / True Color VGA Card  Package Includes: 1 x USB Wireless Receiver 1 x AV Cable 1 x CD ROM(User Manual)        

Description: Wireless Mini Surveillance Camera Monitoring Full Kit With Power Supply Wireless transmission and reception, light weight, small size, low power consumption, High sensitivity, easy to install and operat. Specification: Camera: CMOS Total Pixels:  628 x 582 (PAL) /  510 x 492 (NTSC)  View Angles:  54 degrees Transmission Power:  150mW Consumption Current:  80 mA Effective Range:  30m/100m Power: DC 8V 200mA or 9V battery(not included) Minimum Illumination:  3.0Lux / F1.2 Horizontal Resolution:  380TV Line Operating Temperature: -10°~ +40°C Receiver: Power Supply: AC-DC adapter (DC +9~12v 500mA) Consumption Current: 400mA Power Consumption: Approx. 3W Operation Temperature: -10C~+50C/-40F~+122F Storage Temperature: -40C~+85C/-40F~+185F Operation Humidity: 85% RH Package Includes: 1 X Wireless mini camera 1 X Video Receiver 1 X Antenna 1 X 110V - 220V AC 8V adapter for the camera (will also comes with a mini adaptor according to your country) 1 X Battery clip 1 X 110v - 220V AC 12V adapter for the receiver (will also comes with a mini adaptor according to your country) 1 X Audio / video cable 1 X User manual 1 X Camera stand Details Pictures:    

AEE S50 Full HD 1080P WIFI Mini DV Camcorder Sports Action Camera Feature: 1. 175 degree wide-angle lens. 2. High-definition video recording with multiple interchangeable recording modes. 3. Automatic white balance and automatic exposure. 4. Support external TF card up to 64GB. 5. Support Audio-in function and external dedicated microphone. 6. Support HD port output function. 7. All-round highlight status indicator. 8. Built-in speaker and key tone. 9. Professional water-proof housing design, up to Grade IP68 and 100 meters waterproof. 10. Accessories adopt strengthened structure with improved reliability and stability. 11. Rechargeable built-in high capacity lithium-ion battery extends the video recording time. 12. Built-in microphone adopts dual-Mic design to achieve stereo and high-quality recording effect. 13. 100m wireless remote control allows you to control the video camera functions remotely.(remote control not included) 14. Built-in G-Sensor can function as automobile black box. 15. Burst mode can take 10 photos in 1 second to record every detail in high-speed motion. Specification: View angle 175 Shooting 3M 5M 8M JPEG Battery 1500mAh Lithium battery + 1000mAh makeup battery Average Power consumption 700mA Continuous video recording time Fully charged 128 minutes(1080I/50) 173 minutes (1080P/25) 196 minutes (960P/25) 148 minutes (720P/50) 189 minutes(720P/25) 164 minutes (480P/50) 160 minutes (480P/100) Continuous audio recording time About 192 minutes with fully charged Operating humidity 15~85%RH Storage temperature -20~60 Operating temperature -1~50 Record format MOV Audio recording file WAV USB port MINI 10PIN Distance for Wi-Fi remote control 100 meter (MAX) Wi-Fi transmission distance Up to 100meters in the open area of image transmission Operating system WindowsXP/VistaorAbove/Win 7/Mac OS Package Included: 1 X Camera 1 X Battery 1 X Bracket 1 X SD Card 1 X USB Cable 1 X Charger 1 X CD 1 X User Manual

F eatures: This 2.4 inch TFT LCD screen baby monitor is an amazing product for all parents or nannies to monitor their babies. Addition can be used for a baby monitor, baby monitors applicable to the care of the elderly and the supermarket, office, security companies, schools, families, hospitals and small places. 2.4GHz wireless digital technology, no interference, no privacy leak. Built-in night light. Built-in lullabies, make baby more fast & soft to fall asleep. Built-in rechargeable Li-battery in receiver. Built-in microphone & speaker / two way audio communication. Baby room temperature detection. Specifications: Plug: UK Plug, US Plug, AU Plug, EU Plug for your optional~ Material: ABS(Acrylonitrile Butadiene Styrene) + Electronic components Color: White Operating Frequency: 2400MHz-2483.5MHz Transmission Power: 17dBm Max Monitor Sensitivity: -88dBm Type of Spread Spectrum TX: FHSS Type of Modulation: GFSK Date Rate: 3Mbps Transmission Range: Outdoor 300m (Eye of Sight) Operating Temperature: 0￢ﾄﾃ-+40￢ﾄﾃ Operating Humidity: 85%RH Environment Rating: Indoor use only Camera: Image Sensor Type: 1/3" Color CMOS Image Sensor Effective Pixel: H: 640, V: 480 Lens: EFL=3.6mm.F=2.8 Viewing Angle (Diagonal): 70° IR LED Type/Night Vision Distance: IR LED/ 5m Power Requirement: DC 5V +/- 10% Other Special Feature: Built in Microphone/ Speaker Dimensions: 11.5 x 7cm/ 4.53 x 2.76" Monitor: Display Type/Size: Color TFT2.4" Resolution (Pixel): 960 x 240(RGB) Viewing Angle: H: 80 degree, V: 100 degree Power Requirement: Adapter DC 5V +/- 10% Battery: 3.7V Li-polymer Dimensions: Approx. 12.3 x 6.2 x 2.7cm/ 4.84 x 2.44 x 1.06" Package Included: 1 x Baby Monitor 1 x Wireless Camera 2 x Power Adapter 1 x User Manual Details pictures:

Features: *2.4GHz digital wireless technology, anti-interference, wireless signal, not ip/wifi, or internet. *The wireless signal transmission distance is about 10-50 meters at home, about 50-150 meters outdoor without block, digital baby monitor. *2.4 inch TFT HD LCD displaying, video baby monitor for baby care, wireless baby monitor. *IR Night light and night vision, taking good care of your baby day and night, 24 hours day around, video baby monitor. *2 way talk, 2 way audio, 2 way communication, baby intercom, radio baby monitor. *Temperature monitoring and displaying on the LCD in real time, knowing the temperature of baby's room at any time, audio baby monitor. *4 Lullabies, 4 music tone to help baby fall asleep, comfortable and soft your baby's mind, baby monitor baby monitors. *2X digital Zoom, you can see more clearly of your baby by 2 times bigger, baby monitor with camera. *Power Saver Mode: Video ON/OFF for your choice any time, baby monitor for newborns. *3.7V Li-poly rechargeable battery for the LCD, the camera does not include battery, it is portable for your not with your baby, baby camera with monitor. Specification: General: Operating Frequency Range: ISM 2400MHz-2483.5MHz Transmitting Power: 17dBm Max Monitor Sensitivity: -88dBm Type of Spread Spectrum TX: FHSS Type of Modulation: GFSK Date Rate: 3Mbps Transmission Distance: About 10-50 meters at home, about 50-150 meters outdoor without block Operating Temperature Range: 0-40 Degree Operating Humidity Range: 85% RH Environment Rating: Indoor Use Only Camera (Baby Unit): Image Sensor Type: 1/3’’ Color CMOS Image Sensor Effective Pixel: H: 640, V: 480 Lens: EFL=3.6mm, F=2.8 Viewing Angle: About 70 Degree IR LED Type: 7 pcs IR LEDs IR Night Vision Distance: IR Cut about 3-5 meters Power Requirement: DC 5V Speaker: Built in Microphone 2.4 inch TFT LCD (Parent Unit): Display Type Size: Color TFT LCD 2.4 inch Resolution (Pixel): 960*240 RGB Viewing Angle: H: 80 Degree, V: 100 Degree Power Requirement: DC 5V, 3.7 V Li-polymer Rechargeable Battery Package weight: 450g Package size (L x W x H): 21x17.5x6.5cm Package includeds: 1 x Baby Camera 1 x 2.4 inch Monitor 2 x Power Supply 1 x English User Manual Details pictures:

Description: Dimensions 22.8 × 16.8 × 2.5mm Led Working temperature -30 ¿¿¿ to + 80 ¿¿¿ Operating Voltage 3.3V-4.2V Power voltage> 3.4V Standby average current 3ma less Support the GSM / GPRS four bands, including 850,900,1800,1900MHZ GPRS Class 10 Sensitivity Support voice calls Support SMS text messaging Support GPRS data traffic, the maximum data rate, download 85.6Kbps, upload 42.8Kbps Supports standard GSM07.07,07.05 AT commands and extended commands Ai Thinker Supports two serial ports, a serial port to download an AT command port AT command supports the standard AT and TCP / IP command interface Support digital audio and analog audio support for HR, FR, EFR, AMR speech coding Support ROHS, FCC, CE, CTA certification SMT 42PIN package Package included: 1 x Smart Electronics GPRS Module GSM Module A6 / SMS / Speech / Board / Wireless Data Transmission Adapter Plate

Specification: Arduino 51 STM32 AVR MCU compatible Prototype expand The frequency is 850/900/1800/1900 MHz Power supply range: voltage is 5-12V; current is 1A or more (the current is very important). Operating temperature range: -40 °C to +85 °C Communication interface: The TTL level serial interface compatible 2.85/3.3/5V LED: Two led, the Net led and the RING led. Size: 48*50mm SIMCARD: micro SIMCARD holder Feature: TTL level serial port compatible with 3.3V and 5V microcontrollers. The initial use of computer debugging, it is recommended to use CP2102 USB-TTL module to power supply and communication; Using the MCU control module, you can also using the USB - 232 monitoring return data on the instructions, great convenience to find the problem, especially suitable for 51 MCU. Standby in 30MA or so, you can set the sleep state of about 10MA low power consumption. Support SMS, GPRS data transmission, send MMS, DTMF, HTTP, FTP, PPP dial-up and other functions. The hardware contains one channel reset pin. This reset pin can be used to resolve a problem with the module. Development board supports 2G / 3G / 4G Unicom or mobile phone card. Package includes: 1 x SIM800A Module Wireless Development Board 1 x Antenna Reference picture, test tools does not includes!

ZNV 1.3MP OUTDOOR DOME | ZDIE-2010W-N3T-3.6 Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery ZNV Product Code: ZDIE-2010W-N3T-3.6 Availability: 10 in Stock The dot-matrix IR LEDs makes night surveillance much clearer 1.3MP progressive scan CMOS to capture moving images through anti-aliasing H.264 high profile video compression to provide HD video transmission 960P real-time code stream & dual stream Motion detection alarm to rapidly respond to the outside changes Built-in WEB server for browsing and controlling videos via IE Passwords guard the equipment access Compliant with ONVIF protocol Overview Specifications Product Description ZNV ZDIE-2010W-N3T-3.6 - network surveillance camera Device Type Network surveillance camera - fixed dome Dimensions (WxDxH) 9.3 cm x 9.3 cm x 6.44 cm Weight 310 g Connectivity Technology Wired Camera Colour - Day&Night - NTSC, PAL Max Resolution 1280 x 960 Video Modes 960p Optical Sensor Type CMOS - 1/3" - 1.3 MP Minimum Illumination 0 lux - IR Focal Length Control Fixed focal Focal Length 3.6 mm Interfaces Ethernet 10Base-T/100Base-TX Voltage DC 12 V Features Progressive scanning, ONVIF support, Motion Detection Technology, infrared cut filter, dual video stream, auto white balance Environmental Parameters (operating) -20 °C - 60 °C; 10 - 85% (non-condensing) relative humidity Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a vaild manufacturers warranty/guarantee. Manufacturer's Code: ZDIE-2010W-N3T-3.6 ZNV

This item is sold brand new. It is ordered on demand from our supplier and is usually dispatched in 10 to 15 working days. We urge you to please read shipping details before placing your order. --------------------------------------- Features: 1) High resolution 1/3 inch 2.0 Megapixel CMOS Sensor 2) Integrated 2.8-12mm Megapixel lens 3) Day and night application makes 40M IR view 4) H.264 compression 5) Real time transmission up to 15FPS 6) Two-way audio supported 7) Hardware motion detection supported 8) DC 12V or Power over Ethernet (IEEE 802.3af) 9) Wall mount supported 10) Onvif compliant 11) IP address: http://192.168.1.100 Specifications: 1) Device: 2.0 Megapixel CMOS Sensor 2) Size: 1/3 inch 3) Effective Pixels: 2MP: 1920 x 1080 1MP: 1280 x 720 4) Min. Scene Illumination Color: 0 LUX(IR ON) 5) B/W: Yes 6) IR Sensitivity: Yes 7) IR Cut: Yes 8) Lens: 2.8-12mm 9) Viewing Angle: 33-78 (Horizontal) 10) Linux System: Internal Linux system 11) Day/Nigh: IR distance 40 M 12) Functions: Motion Detection 13) Electronic Shutter: 1/5-1/15000 sec 14) BLC: Yes 15) AGC: Auto 16) White Balance: Auto 17) S/N Ratio: >50 dB 18) Video Compression: Compression H.264 19) Picture Resolution: 2.0 MP (1600 x 1200) HD (1280 x 720) 20) Bit Rate: 80 K~ 2.0 Mbps 21) Image Frame Rate: 15 FPS 22) Audio: Compression G.726 23) Casing Mount Types: wall bracket 24) Network: Ethernet (10/100 Base-T) RJ-45 connector 25) Protocol: TCP UDP IP HTTP FTP SMTP DHCP DNS ARP ICMP POP3 NTP RTP RTCP 26) Software Web Browser: Microsoft Internet Explorer 6.0 above 27) SDK: SDK-H 28) Security: Administrator password protection 29) Operating Temperature: -10~50C (14~122F) 30) Humidity: -10~85% 31) Power Requirement: PoE (IEEE802.3af) 32) Power Consumption: 12-13W (DC 12V 1A) 33) Approvals Certification: CE FCC 34) Size: 28.5 x 12 x 8cm --------------------------------------- See what else we're selling

SELECTED OPTION: ADAPTOR: USPLUG CLICK HERE for more options in this item. Features: HD quality start from the lens. Two way voice intercom. Intelligent motion detection. Phone alarm push. Remote PTZ. Safe local storage, permanent free. Simultaneously online viewing. Four pictures. Support multiple platforms to watch. WiFi connection, only three steps.   Specification: Anpwoo YT002W Main processor Ingenic T10 Operate system Embedded LINUX operating system Image coding H.264(High Profile) Resolution 720P / VGA / QVGA Code rate Support CBR/VBR,128-4096Kpbs Frame rate 5 / 10 / 15 / 20 / 25 FPS adjustable Format ADPCM format, G711, 8K sampling rate Connect method Support for P2P, TCP connection mode Local playback Monitor in real time and talk-back, half-duplex audio transmission (mobile app) PTZ control PTZ control, vertical 120 °, horizontal 355 ° Network Protocol FTP/SMTP/P2P/TCP/IP/UPnP/HTTP/HTTPS/UDP/DHCP/DDNS/RTSP ONVIF2.0 User Administrator, operator, visitors three level user management rights management ID Anti-theft ID support the additional password code,unlawful use the stolen ID is invalid Motion detection Alarm support motion detection, 1~10 sensitivity adjustable Voice alarm Sensitivity adjustable high/medium/low Alarm linkage Alarm email send, alarm output, PTZ automatic steering, client alarm, FTP upload picture Built-in Built-in TF card slot, support the SDXC standard, maximum support 64G WiFi Built-in WiFi module, supports 802.11b/g/n IR 11pcs night vision infrared light, wavelength 850nm, range 10m IR-CUT Double filter automatic switch Photosensitive Sensitivity 0.7Ω/Lux Mobile app Support Andriod/iOS platform Web client Supports IE, Firefox, mobile browser PC client Support XPWin7Win8Win8.1Win10 Power DC 5V2A, USB cable provide Humidity Applicable humidity range (85%RH) Temperature Applicable temperature range (0 to 45℃) Product Weight 220g

Product Specification POWER. Guide No. (ISO100).meters 43 (105mm). ZOOM. Zoom head Yes focal length coverage 24-105mm Coverage with wide panel 14mm Auto zoom for sensor size Yes. FLASH MODES. Auto exposure control E-TTLII/E-TTL High speed sync (FP) Yes Manual / output settings Yes - 1/1- 1/128 Manual steps 1/3 step. FLASH-RELATED FUNCTION. FE lock Yes Flash exposure compensation Yes Flash Exposure bracketing No Second-curtain flash sync Yes Modelling flash Yes Colour temperature info communication Yes. WIRELESS FLASH. Transmitter Yes Transmission type Radio Signal range (Infra-red/Radio) Indoors: 12-15m / 30m Outdoors: 8-10m / 30m Slave function Infra-red/Radio Master function Radio No of groups (Optical/Radio) - / 5 No of channels (Optical/Radio) - / 15 Remote Shutter Release Yes. FLASH HEAD MOVEMENT. Up 45, 60, 75 and 90° Left 60, 75, 90, 120, and 150° Right 60, 75, 90, 120, 150 and 180 °. AF ASSIST. AF-assist beam Yes Number of AF points supported 1 AF-assist beam type Infra-red / flash strobe. POWER SOURCE. Battery 4 x AA batteries Minimum recycling time * Approx. 3.5 sec External power supply No. CONSTRUCTION. Dust and water resistance No Mounting foot material Metal. MISC.. Custom function 10 (8 personal functions) Flash settings from camera menus ** Yes External flash exposure sensor No PC terminal No Compatible Accessories Off-camera shoe cord OC-E3 Bounce adapter SBA-E2 Color filter/Bounce adapter holder Color filter SCF-E2 Dedicated flash bracket No. DIMENSIONS & WEIGHT. Size (W x H x D), mm 70.5 x 113.8 x 98.2 Weight (Excluding batteries), grams 295g Working temperature range 0 °C - 45 °C / 32 °F - 113 °F Working humidity 85 % or less. All data is based on Canon standard testing methods (according to CIPA Standards) except where indicated. Subject to change without notice. * time taken to recharge flash after full discharge using Alkaline AA batteries ** With compatible cameras only..

CANOpen J1939 DeviceNet USBCAN-2 CANalyst-II Description: 32-bit, 80M high-frequency high-performance processor with 512K flash, 128K SRAM storage space to buffer the CAN 6000 information. Support for advanced online programming (online writing FLASH) can save the configuration information and status in real time CAN without power are cumbersome to configure each. 10K ~ 1M baud rate range in any configuration, with Baud Rate configuration tools, one-click configuration. 10K ~ 1M baud rate range measured in any frame Perfect support win8 / win7 / xp 64bit / 32bit USB3.0 / USB2.0 / USB1.1. win8 64bit + USB3.0 to achieve optimal performance. Unique encryption technology: the user secondary development of software, add-shelf packaged good encryption code, can achieve a unique software and hardware binding, of course, you can also create a set of keys in software, the software is bound to achieve a particular a group of devices Feature: USB and CAN protocol conversion; CANalyat-II analyzer (Extreme Edition) includes two CAN interfaces; USB interface supports USB2.0, compatible with USB1.1; CAN2.0A CAN2.0B protocol support and supports standard and extended frames; Support bi-directional transmission, CAN send, CAN reception; It supports data frame, remote frame format; CAN controller baud rate between 10Kbps-1Mbps optional software configurable; CANalyst-II analyzer (Extreme Edition): CAN bus interface using high-speed magnetic coupling isolation, isolated DC-DC power supply; three-terminal full isolation (USB bus and CAN bus isolation, CAN1 and CAN2 isolation room) Maximum flow: two CAN channels (and running), respectively, received 8500 / s, sending 8500 / s; (two channels simultaneously receiving 8500 / s, USB speed of up to 17,000 / s speed, no dropped frames) Internal CAN transmit buffer capacity for each channel 1000 (failed to send automatic retransmission), CAN receive buffer capacity for each channel 2000; USB bus directly powered, no external power supply; CANalyst-II Analyzer, isolation module insulation voltage: 2500V; Working temperature: -40 ~ 85 ℃ Package included: 1 x CANalyst-II

ZNV 1.3MP OUTDOOR DOME | ZDIE-2010W-N3T-3.6 Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery ZNV Product Code: ZDIE-2010W-N3T-3.6 Availability: 10 in Stock The dot-matrix IR LEDs makes night surveillance much clearer 1.3MP progressive scan CMOS to capture moving images through anti-aliasing H.264 high profile video compression to provide HD video transmission 960P real-time code stream & dual stream Motion detection alarm to rapidly respond to the outside changes Built-in WEB server for browsing and controlling videos via IE Passwords guard the equipment access Compliant with ONVIF protocol Overview Specifications Product Description ZNV ZDIE-2010W-N3T-3.6 - network surveillance camera Device Type Network surveillance camera - fixed dome Dimensions (WxDxH) 9.3 cm x 9.3 cm x 6.44 cm Weight 310 g Connectivity Technology Wired Camera Colour - Day&Night - NTSC, PAL Max Resolution 1280 x 960 Motion Detection Yes Video Modes 960p Optical Sensor Type CMOS - 1/3" - 1.3 MP Minimum Illumination 0 lux - IR Focal Length Control Fixed focal Focal Length 3.6 mm Interfaces Ethernet 10Base-T/100Base-TX Voltage DC 12 V Features Progressive scanning, ONVIF support, Motion Detection Technology, infrared cut filter, dual video stream, auto white balance Environmental Parameters (operating) -20 °C - 60 °C; 10 - 85% (non-condensing) relative humidity Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a valid manufacturers warranty/guarantee. Manufacturer's Code: ZDIE-2010W-N3T-3.6 ZNV

Features: - 6V 3W polycrystalline solar panel with USB charging - High conversion rate, high efficiency output. - Excellent low light effect. - Mining high temperature tempered glass transmission. - Unique technology to avoid water freezing and deformation within. - Environmental protection and energy-saving, easy-to-use, feel free to phone or charge digital products. - For mobile phones, tablet PCs, MP3s, MP4s and other digital direct charging products. Specifications: Size: approx.. 128x135x2mm / 5 "x5.3" x0.078 " Power: 3W Operating voltage: 6V Output interface: USB 2.0 Operating temperature: -20 ??- + 85 ??/span> Weight: 150g Package Included: 1x 6V 3W Solar Panels

Wemos TTGO LoRa32 V2.1 868Mhz ESP32 LoRa OLED 0.96 Inch SD Card Bluetooth WIFI Wireless Module Description: Working voltage: 1.8~3.7VAcceptable current: 10~14mATransmit current: 120mA@ 20dBm 90mA@ 17dBm 29mA@ 13dBmOperating frequency: 868MHzTransmit power: 20dBmReceive sensitivity: -139dBm@LoRa &62.5Khz&SF=12&146bps-136dBm@LoRa &125Khz&SF=12&293bps-118dBm@LoRa &125Khz&SF=6&9380bps-123dBm@FSK&5Khz&1.2KbpsFrequency error: /-15KHzFIFO space: 64ByteData rate: 1.2K~300Kbps@FSK 0.018K~37.5Kbps@LoRa Modulation Mode: FSK, GFSK, MSK, GMSK, LoRa TM, OOKInterface form: SPISleep current: 0.2uA@SLEEP 1.5uA@IDLEOperating?temperature: -40￢ﾄﾃ- 85￢ﾄﾃDigital RSSI functionAutomatic frequency correctionAutomatic gain control RF wake-up functionLow voltage detection and temperature sensorFast wake-up and frequency hoppingHighly configurable data packet handlerSMA AntennaIP5306More product information, go to: httpss://github.com/LilyGO/TTGO-LoRa32-V2.1At the TTGO LoRa V2.1, we add the SMA and IP5306 to the board, which make it can do more things. In terms of the power switch, we have changed the switching interaction mode. The added SMA antenna can enhance signal transmission.Package included: 1 x TTGO LoRa32 V2.1 868Mhz Module2 x Pin1 x Antenna1 x Power Cable(Notice:The shipping list does not include battery and SD card)

Features: This 3.5 inch TFT LCD screen baby monitor is an amazing product for all parents or nannies to monitor their babies. Addition can be used for a baby monitor, baby monitors applicable to the care of the elderly and the supermarket, office, security companies, schools, families, hospitals and small places. 2.4GHz wireless digital technology, no interference, no privacy leak. Built-in night light. Built-in lullabies, make baby more fast & soft to fall asleep. Built-in rechargeable Li-battery in receiver. Built-in microphone & speaker / two way audio communication. Baby room temperature detection. Specification: Monitor: Display: 3.5" TFT LCD Resolution: 320x240(RGB) Viewing Angle: H: 80 degree, V: 100 degree Power Requirement: DC 5V±10% Battery: 3.7V Li-polymer Dimensions: Approx. 11.9x4.6x9.4cm/ 4.69x1.81x3.70" Camera: Sensor: 1/3" Color CMOS Image Sensor Effective Pixel: H: 640, V: 480 Lens: EFL=3.6mm. F=2.8 Viewing Angle (Diagonal): 70 degree IR LED Type/Night Vision: 8 pcs IR LED-850nm/5m Power Requirement: DC 5V +/-10% Other Special Feature: Built in Microphone/Speaker Dimensions: Approx. 9x5.5x8.7cm/ 3.54x2.17x3.43" Material: ABS (Acrylonitrile Butadiene Styrene) + Electronic components Frequency: 2.4GHz Digital Monitor Sensitivity: -88dBm Type of Spread Spectrum TX: FHSS Type of Modulation: GFSK Data Rate: 3 Mbps Transmission Range: Outdoor 300 m (Eye of Sight) Operating Temperature Range: 0??to +40??br />Operating Humidity Range: 85%RH Environment Rating: Indoor use only Package includeds: 1 x Baby Monitor 1 x Wireless Camera 2 x Power Adapter (Come with an adapter according to your country~) 1 x User Manual Details pictures:

Lenkeng LKV375-100 HDbaseT 100m | CNV-LKV375-100 Brand New & Sealed * Original Product * Valid Manufacturer's Guarantee * Fast Delivery Lenkeng Product Code: CNV-LKV375-100 Availability: 27 in Stock HDMI HDBaseT extend technology Supports 4Kx2K Transmission with 0 loss Supports bi-directional IR pass back Overview This HDBaseT single network cable extender transmits HDMI signal fluently and clearly. It is lossless in signal and supports 3D, 24bits deep color, 4kx2k, CEC and HDCP. Specifications Product Description Lenkeng LKV375-100 Transmitter and Receiver - video/audio/infrared extender - HDMI, HDBaseT Device Type Video/audio/infrared extender Form Factor External Data Link Protocol HDMI, HDBaseT Max Transfer Distance 100 m Dimensions (WxDxH) 6.65 cm x 9.85 cm x 2.3 cm Delivery & FAQ's * Metropolitan Areas - Delivery of this item within 3 business days after payment reflects * Outlying Areas - Please allow 5 business days after payment reflects for delivery of this item This item carries a valid manufacturers warranty/guarantee. Manufacturer's Code: CNV-LKV375-100 Lenkeng