Rode windshield

Rode - RODIXY Stereo Microphone For iPhone and iPad The RØDE iXY is the ultimate recording microphone for iPhone® or iPad®. With up to 24-bit/96k* recording and on-board high-fidelity A/D conversion, your iXY recordings are rich, smooth and accurate. At the heart of the iXY is a matched pair of ½” cardioid condenser capsules, fixed in a perfect 90 degree ‘near-coincident’ alignment. This results in immersive and true-to-life stereo recordings, captured in incredibly high detail. The iXY is supplied with a foam windshield for outdoor recording as well as a reinforced protective zip case to ensure your iXY is available whenever you need it. For more information and to hear audio samples visit www.ixymic.com. The iXY is compatible with iPhone® 4S, iPhone® 4, iPad® (3rd generation), iPad® 2 & iPad®. *RØDE Rec or RØDE Rec LE app required for quality.

Rode - NT6 Small Diaphragm Condenser Microphone The new Rode NT6 is a small-diaphragm condenser microphone that's specifically designed for difficult mounting applications or discreet placement. The compact capsule of the NT6 is connected to the main part of the mic by a 3-meter Kevlar-reinforced cable. The NT6 runs on standard 48-volt phantom power. The mic has a fixed cardioid pattern, a frequency range of 40Hz-20kHz and a maximum SPL figure of 135dB. The new NT6 is extremely well suited to any situation where a small unobtrusive but powerful microphone system is required. It features a unique compact capsule connected to the main body of the mic by a three-meter cable, making it perfect for discrete instrument miking, especially in tight spaces. The NT6's mic body, which houses the preamp and XLR connector, also features -10dB pad and 80Hz highpass filter switches, so you can adjust these settings without disturbing the position of the capsule. The NT6 is supplied with all the necessary mounting hardware, a windshield and a zip-up pouch

Rode NTG2 Multi-Powered Shotgun Microphone The RØDE NTG2 is a lightweight condenser shotgun microphone, designed for professional applications within the film, video, television and production industries. Its full frequency response, low noise and audio transparency make it an ideal film, video, and voice over microphone, while its low weight (161gm/5.7oz without battery) makes it an ideal boom microphone. In addition to the native 20Hz-20kHz frequency response a selectable high-pass filter at 80Hz is available, which will prevent low end noise such as air conditioners and traffic from being recorded. The NTG2 operates either from a AA (1.5V) battery or P48 phantom power which can be supplied by professional cameras, audio recorders and power supplies. The battery power option makes the NTG2 ideal for scenarios where the camera does not supply phantom power such as DSLR video. The WSVM windshield is supplied to minimise light wind noise and plosives during recording. The optional ‘DeadCat’ furry is recommended for outdoor applications.

Rode VMPRPLUS Videomic Pro-R+ On-Camera Shotgun Condenser Microphone Product Description The RØDE VideoMic Pro+ is a new addition to the best-in-market on-camera category. It is a true shotgun microphone designed for use with camcorders, DSLR cameras and portable audio recorders as a source of primary and reference audio. Binding: Electronics Brand: Rode ProductGroup: Musical Instruments ProductTypeName: SOUND_AND_RECORDING_EQUIPMENT Features: Automatic Power Function with plug-in power Power via LB-1, 2 x AA Batteries, Micro USB Ships with LB-1 Lithium-Ion Rechargeable Battery, Detachable 3.5mm TRS Cable, Micro USB Cable Optimized Windshield Shape Digital Switching. Camera shoe mount with 3/8 Inch thread for easy boompole mounting

Rode - M3 Dual Power Condenser Microphone The M3 is an extremely versatile microphone that is at home in the studio, on location, or wherever a low-noise wide-response cardioid condenser microphone is demanded. An end address condenser microphone, the M3 features a heavy-duty metal body, category leading low self-noise, three stage PAD (O, -10db, -20db), a battery status LED and a High Pass Filter. The M3 also comes complete with windshield and a stand mount, and can be powered via a 9V battery or V Phantom.

Rode - M3 Dual Power Condenser Microphone The M3 is an extremely versatile microphone that is at home in the studio, on location, or wherever a low-noise wide-response cardioid condenser microphone is demanded. An end address condenser microphone, the M3 features a heavy-duty metal body, category leading low self-noise, three stage PAD (O, -10db, -20db), a battery status LED and a High Pass Filter. The M3 also comes complete with windshield and a stand mount, and can be powered via a 9V battery or 24-48V Phantom.

The Rode Dead Wombat is an artificial fur windshield designed to minimise wind noise when recording in high wind conditions. This windshield is compatible with the Rode Blimp. For more information, see it on the Rode website here

The Rode Blimp is a windshield and shock mounting system for the Rode NTG1. NRG2 and NTG3 microphones. It also works with third party microphones up to 325mm in length. Featuring the Rycote lyre suspension system, the Rode Blimp provides fantastic suspension and isolation for your mic. Quick Facts: constructed from hard-wearing thermoplastic provides superior acoustic suspension heavy-duty Mogami cable inside the grip attaches to any standard boompole with a 3/8" thread For more information, see it on the Rode website here

The Rode Dead Kitten Windshield is used to minimise wind noise when recording in high wind conditions. This windshield is used for smaller mics including the Stereo Videomic and the Stereo Videomic Pro For more information, see it on the Rode website here

The Rode Dead Cat Windshield is used to minimise wind noise when recording in high wind conditions. This windshield is specifically for the VideoMic Pro. For more information, see it on the Rode website here

The Rode Dead Cat Windshield is used to minimise wind noise when recording in high wind conditions. Quick Facts: no animals were harmed during the manufacture of this item For more information, see it on the Rode website here

Estimated delivery time: working days (Imported from the UK) - T&C's Apply Please note that all Christmas gift orders need to be placed before the 14th of November to ensure that they are delivered to you in time. This item includes free delivery within South Africa. The DeadCat VMP windshield is designed for minimising any wind noise when recording with the VideoMic Pro in windy conditions.Its artificial fur is specially designed so as to minimise wind noise while remaining acoustically transparent.* Microphone sold separatelyWeight gmDimensions mmH x mmW x mmD

The new RODE NTG-1 is a lightweight condenser shotgun microphone, specifically designed for professional applications within the film, video, television, voiceover and ENG industries. The NTG-1 provides an electronically balanced output stage and operates on 48 V to the P48 standard. The NTG-1 offers wide bandwidth and a controlled polar response coupled with low noise SMT electronics. The NTG-1 is extremely lightweight making it ideal for mounting directly to video cameras (with optional accessories) or a Boom pole. The NTG-1 comes complete with mount and windshield. The supplied windscreen effectively suppresses wind noise when recording outdoors in moderate conditions. Optional accessories are available for more demanding applications. Features - Broadcast sound quality - Low noise circuitry - Condenser transducer - Rugged metal construction - Low weight: 105 grams approx. (3 oz.) - Low handling noise - Supplied with stand mount, zip pouch and windshield - Designed & manufactured in Australia

The Rode Blimp Extension Kit is an add-on extension of the Rode Blimp, allowing you to use the Blimp with long shotgun mics, including the NTG8, or any third party mic up to 600mm. Quick Facts: includes a 256mm extension piece, two sets of silicone bands, and an extra long Dead Wombat fur windshield and brush The Rode Blimp is required in order to use this product For more information, see it on the Rode website here

The Rode VideMic GO offers directional audio on the go. It's compact and light-weight design makes it ideal for DSLR users. Quick Facts: high quality directional mic no battery needed integrated shock mount 3.5mm mini-jack output inegrated cold-shoe with 3/8" thread comes with a windshield For more information, see it on the Rode website here

The Rode VideoMic is a fantastic entry level shotgun microphone to use with consumer video cameras and audio recorders. Quick Facts: studio recording quality 9v battery windshield included 3.5mm mini-jack output integrated cold-shoe mount with 3/8" thread For more information, see it on the Rode website here

The silver Rode NTG-3 Shotgun Microphone is a professional shotgun microphone that delivers a few unique qualities in order to meet the demands of today's broadcast audio engineers and boom operators. The microphone features radio-frequency (RF) interference properties that avoid annoying noise and interference caused by nearby RF sources such as radio antennas, WIFI networks, internet devices, power lines, etc. The microphone is also built to withstand the rigors of adverse weather conditions. Of course special attention is paid to the accurate, directional pickup characteristics and its frequency response, sensitivity and low noise floor, which result in pristine audio quality. The NTG-3 shotgun microphone is an ideal solution for outdoor ENG and studio applications. RF Rejection The microphone features radio-frequency (RF) interference properties that avoid annoying noise and interference caused by nearby RF sources such as radio antennas, WIFI networks, internet devices, power lines, etc. Withstands Adverse Conditions The microphone is constructed to withstand adverse weather conditions for more stable use outdoors. Supercardioid Line+Gradient Pickup The supercardioid, shotgun characteristics provide excellent off-axis rejection, focused pickup and longer range. Specifications Transducer Condenser Polar Pattern Line-Gradient Supercardioid Frequency Response 40Hz to 20kHz Dynamic Range (Typical) 117dB Signal-to-Noise Ratio 81dB SPL (A-weighted) Maximum Input Sound Level 130dB Power Requirements 48V Phantom Power Output Impedance Nominal: 25 ohms Output Connectors 3-pin XLR Pad No Low Frequency Roll-Off No Dimensions (LxDiameter) 10 x 0.74" (255 x 19mm) Weight 5.74oz (163g) In the Box Water Resistant Aluminum Storage Case Windshield Zip Pouch Microphone Clip 10 Year Warranty

The Rode M5 Compact 1/2" Condenser Microphone matched pair have variation of no more than 1dB of sensitivity between microphones. The M5 itself is a pencil-style mic that features a 1/2" diameter gold-plated membrane capsule with a cardioid polar pattern. The mics have transformerless circuitry for low noise operation and can be used in typical live and studio applications for small diaphragm condenser mics, including on acoustic instruments, choirs, as drum overheads, and more. The M5s are finished with Rode's proprietary ceramic coating and each include a WS5 windshield and RM5 mic clip. The pair was designed and built in Australia and has a limited 1-year warranty that extends to 10-years with on-line registration. Acoustic Principle - Pressure Gradient Active Electronics - JFET impedance converter with bi-polar output buffer Capsule Diameter - 0.50" (12.7 mm) Polar Pattern - Cardioid Address Type - End Frequency Range 20 Hz to 20 kHz Output Impedance 200 ? Maximum SPL 140 dB SPL (@ 1 kHz, 1% THD into 1 k? load) Maximum Output Level 13.5 dBu (@ 1 kHz, 1% THD into 1 k? load) Sensitivity -34.0 dB re 1 V/Pa (10.46 mV @ 94 dB SPL) /- 2 dB @ 1 kHz Equivalent Noise Level 19 dB-A (A-weighted) Phantom Power 24, 48 V Output 3-pin XLR Dimensions (HxWxD) 4 x 1 x 1" (100 x 20 x 20 mm), per microphone Weight 2.8 oz (80 g), per microphone

Stylish and modern, the M3 represents RODE's outstanding microphone technology and their continuation of bang-for-the-buck thinking. Built for studio, stage, and location work, the M3 is made from only the finest components, and delivers the sonic results demanded by engineers and musicians alike - and at a price that makes the M3 attainable by anyone. A permanently polarized condenser microphone, the M3 can be powered via its internal battery or by external phantom power. Its low self-noise, high fidelity performance, and value pricing make the M3 hard to beat. Features: Acoustic principle: Permanently polarized condenser Directional pattern: Cardioid Frequency range: 40Hz-20kHz Output impedance: 200 ohms Signal noise ratio: 73dB SPL (per IEC651) Equivalent noise: 21dbA SPL (a - weighted per IEC651) Maximum SPL: 142dB (@ 1kHz, 1% THD into 1kohm load) Sensitivity: -40dB+/-3dB re 1V/Pa @ 1kHz (6.3mV/Pa @ 94db SPL) Dynamic range din iec 651: 121dB (per IEC651) Power supply voltage: 1.6mA (battery)/6.5mA (48V Phantom Power) Battery life: >200 hours Output connection: 3 pin XLR Complete with windshield and a stand mount

Estimated delivery time: working days (Imported from the UK) - T&C's Apply Please note that all Christmas gift orders need to be placed before the 14th of November to ensure that they are delivered to you in time. This item includes free delivery within South Africa. Instruction Manual (Acrobat pdf file) Spec sheet (Acrobat pdf file)Studio and location Multi Powered Condenser Microphone The M3 is an extremely versatile microphone that is at home in the studio on location or wherever a low-noise wide-response cardioid condenser microphone is demanded.An end address condenser microphone the M3 features a heavy-duty metal body category leading low self-noise three stage PAD (O -10db -20db) a battery status lED and a High Pass Filter.The M3 also comes complete with windshield and a stand mount and can be powered via a 9V battery or V Phantom. Rugged metal body Internal capsule shock mount Switchable High-Pass Filter @ 80Hz-12dB/Oct Three step PAD - Flat -10dB and -20dB low handling noise Heat treated high strength head mesh 9V battery power or V phantom power Battery status indicator SpecificationPower PV) PV) phantom supply or 9V battery Acoustic Principle Pressure gradient Directional Pattern Cardioid Frequency range 40 Hz - 20 kHz Output impedance 200Ohm Signal noise ratio 73 dB SPl (A - weighted per IEC651) Equivalent noise 21 dB SPl (A - weighted per IEC651) Maximum SPl 142dB SPl (@ 1kHz 1% THD into 1KOhm load) Maximum output voltage +9.22dBu (@ 1kHz 1% THD into 1KOhm load) Sensitivity -40 dB re 1 Volt/Pascal (10 mV @ 94 dB SPl) +/- 3 dB @ 1kHz Weight 390gm Dimensions 225mmH x 33mmW x 33mmD Included Accessories Carry case RM3 stand mount and WSM3 wind shield Optional Accessories DS1 desk stand and Tripod

The DeadWombat windshield is designed for minimising wind noise when recording in high wind conditions using the RDE Blimp. Its artificial fur is specially designed so as to minimise wind noise while remaining acoustically transparent.

No battery required Integrated Rycote Lyre shock mounting Our lightest mic at only 73g Rugged reinforced ABS construction Windshield included 3.5mm mini-jack output Integrated cold-shoe mount with 3/8 thread Two year extended warranty when you register your microphone Clear, directional audio on the GO! Compact and light weight by design, the VideoMic GO delivers clear, crisp, directional audio with incredible ease of use. Its tight pickup area focuses directly in front of the microphone and reduces other surrounding sounds, ensuring that your subject is isolated from distracting background noise. The integrated Rycote Lyre shock mount isolates your microphone from bumps and vibrations that could otherwise interfere with your sound. Constructed from a single piece of hard-wearing thermoplastic, the Lyre provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap. The VideoMic GO has no complicated switches or settings and is powered by your camera's external microphone input, requiring no batteries to operate, ensuring you never miss a great shot. The VideoMic GO is designed and made in Australia.

The WS2 windshield provides additional protection for the microphone capsule against any wind noise or plosives. Compatible Microphones K2 NTK NT2000 NT2-A NT1000 NT1-A NT1-A Matched Pair Podcaster Procaster Broadcaster

The RDE HS2 is a low profile, ergonomic and lightweight headset microphone that provides clean, clear and pronounced audio for any application where the microphone needs to be in close proximity to presenter's mouth. The result of an extensive and complete redesign process, the RDE HS2 features an adjustable corrosion resistant stainless spring-steel boom arm and headband connected to pliable hypoallergenic silicone ear strips for maximum flexibility and user comfort. Coated in a durable ceramic painted finish in either black (HS2-B) or pink (HS2-P) the HS2 is also available in two different sizes (small or large) to ensure the perfect fit and function for any individual. The headset is connected via a 1.2m (4') braid shielded, Kevlar reinforced cable, terminating at a gold plated 3.5mm TRS output with a removable locking nut to ensure a secure connection to a wide range of recording devices and wireless transmitters, including the RDE Filmmaker and Newsshooter kits. The HS2's light weight, comfortable fit, low self-noise, minimal appearance and user friendly omni-directional polar pattern make it an ideal microphone for film, television, video, theatre, house of worship and live vocal performance. Updated low-profile ergonomic design Ultra-Lightweight construction for complete comfort Adjustable corrosion resistant stainless spring steel boom arm and headband Flexible hypoallergenic sillicone ear strips Durable ceramic painted finish available in black or pink Available in small or large sizes Omni-directional polar pattern Low handling noise Includes Mini-furry and pop filter / windshield 1.2m Kevlar reinforced braid shielded cable Gold plated 3.5mm TRS output with removable locking nut Five year extended warranty when you register your microphone

Basically new Rode VideoMic with Rycote Lyre Suspension System, produce really good audio quality. Comes with windshield attached and 2 free batteries. Price slightly negotiable. Collect in Stellenbosch or I can post it to you.

lightweight on camera microphone for dslr cameras and video cameras high quality directional microphone www.sbrprosound.co.za no battery required integrated rycote lyre shock mounting rugged reinforced abs construction windshield included mini-jack output integrated cold-shoe mount with 3/8” thread

compact cardoid on camera microphone www.sbrprosound.co.za compact size and lightweight all-metal microphone body no battery required rycotelyre shock mount included deluxe furry windshield included designed and manufactured in australia