Rf 602rx wireless flash

RF-603 SPEEDLIGHT FLASH TRIGGERS FOR CANON The RF-603 Wireless Flash Trigger act as a wireless flash trigger as well as wireless shutter release trigger. RF-603 supports all Canon DSLR Camera and support Flash Speedlight with "Sleep mode" function: Nikon Canon Olympus Pentax Samsung and other Speedlight flashes which has "Wake up" function The RF603 has been improved in several functions: Transceiver-based system: units automatically detect when to switch to either transmitter or receiver mode. Hot shoe pass-through, allowing on-camera flash and radio triggering to be used simultaneously. Improved shutter sync speed up to s Use AAA batteries (not included) Improved on/off switch Prontor/Compur (PC) port for off-hot shoe synchronisation Non-proprietary 2.5mm (sub-miniphone) port for shutter release cables Shutter release cable included (Select between C1- and C3 cable) Since it is now a transceiver system you can now use it more flexible. With e.g. 4 RF-603 you can trigger 3 flashes (1 trigger, 3 receivers) as well as trigger the camera itself and then trigger 1 flash. One more good thing is that the only power source you now need is 2 AAA batteries. The power switch has been improved an now should prevent from accidently firing in the camera bag which could consume a lot of the battery power. Features:   Wireless flash trigger: As a flash trigger, RF-603 trigger both flash Speedlight and studio flashes the flash sync speed is up to s Transmission distance: 100m Wireless shutter release (C1 shutter connecting cord included to supports Canon 60D 70D 350D 450D 500D 550D 600D 650D 700D D D D): (C3 shutter connecting cord included to supports Canon 1D 5D 6D 7D 20D 30D 40D 50D) As the wireless shutter release, its working range is up to 100 meters (clear outdoor environment) Full-way press the release button can starts continuous shooting or long exposure   Features and specifications: 2.4GHz band-16 selectable operating frequencies to eliminate chance of interference The RF-603 transceiver system can be used to trigger all studio flash units through standard PC socket Flash sync speed: s Operating distance: 100m Shutter interface: 2.5mm socket Release: half-way press, full-way press Battery: AAA x 2 Receiver stand-by time: up to 45 hours Package include: 2 x RF-603 Transceivers for Canon cameras 1x cable for shutter release function (C1 shutter connecting cord included to supports Canon 60D 70D 350D 450D 500D 550D 600D 650D 700D D D D): (C3 shutter connecting cord included to supports Canon 1D 5D 6D 7D 20D 30D 40D 50D) English Manual   PLEASE REMEMBER TO INDICATE WHICH ONE OF THE CABLES YOU REQUIRE (IF YOU WANT BOTH THE C1 AND C3 CABLES - PLEASE ADD R50 FOR THE SECOND CABLE) I ONLY POST TO ADDRESSES IN SOUTH AFRICA - NO INTERNATIONAL SALES

SINGLE RF-603 SPEEDLIGHT FLASH TRIGGER FOR CANON The RF-603 Wireless Flash Trigger act as a wireless flash trigger as well as wireless shutter release trigger. RF-603 supports all Canon DSLR Camera and support Flash Speedlight with "Sleep mode" function: Nikon Canon Olympus Pentax Samsung and other Speedlight flashes which has "Wake up" function The RF603 has been improved in several functions: Transceiver-based system: units automatically detect when to switch to either transmitter or receiver mode. Hot shoe pass-through, allowing on-camera flash and radio triggering to be used simultaneously. Improved shutter sync speed up to s Use AAA batteries (not included) Improved on/off switch Prontor/Compur (PC) port for off-hot shoe synchronisation Non-proprietary 2.5mm (sub-miniphone) port for shutter release cables Shutter release cable included (Select between C1- and C3 cable) Since it is now a transceiver system you can now use it more flexible. With e.g. 4 RF-603 you can trigger 3 flashes (1 trigger, 3 receivers) as well as trigger the camera itself and then trigger 1 flash. One more good thing is that the only power source you now need is 2 AAA batteries. The power switch has been improved an now should prevent from accidently firing in the camera bag which could consume a lot of the battery power. Features:   Wireless flash trigger: As a flash trigger, RF-603 trigger both flash Speedlight and studio flashes the flash sync speed is up to s Transmission distance: 100m Wireless shutter release (CABLES NOT INCLUDED - AVAILABLE FOR R50 EXTRA) (C1 shutter connecting cord included to supports Canon 60D 70D 350D 450D 500D 550D 600D 650D 700D D D D): (C3 shutter connecting cord included to supports Canon 1D 5D 6D 7D 20D 30D 40D 50D) As the wireless shutter release, its working range is up to 100 meters (clear outdoor environment) Full-way press the release button can starts continuous shooting or long exposure   Features and specifications: 2.4GHz band-16 selectable operating frequencies to eliminate chance of interference The RF-603 transceiver system can be used to trigger all studio flash units through standard PC socket Flash sync speed: s Operating distance: 100m Shutter interface: 2.5mm socket Release: half-way press, full-way press Battery: AAA x 2 Receiver stand-by time: up to 45 hours Package include: 1x RF-603 Transceiver for Canon cameras I ONLY POST TO ADDRESSES IN SOUTH AFRICA - NO INTERNATIONAL SALES

SKU: -CALIRF603C3nnB    This item is used for Canon, its transmitter is also the receiver. When you press each of them, another will become the receiver. You can use 2 flash with this transmitter and receiver. It is perfect for creative photography.  Note: With no special use transmitter, without the function of waking-up. This product don't support SB-600 flashgun.   Features: 2.4GHz band-16 selectable operating frequencies to eliminate chance of interference The RF-603 transceiver system can be used to trigger all studio flash units thro standard PC socket Flash sync speed: s Operating distance: 100m Shutter interface: 2.5mm socket Release: half-way press, full-way press Battery: 2 x AAA (NOT included) Receiver stand-by time: up to 45 hours   Compatible: Canon 1D / 1DS, EOS 5D Mark II / 5D / 50D / 40D / 30D / 20D / 10D Suit for Flash Speedlite with " Sleep mode" function:    - Nikon   - Canon   - Olympus   - Pentax   - Samsung Yongnuo YN-460, YN-460 II, YN-560, YN-465, YN-467, YN-468 in manual mode and other flashgun which has " Wake up " function   What you will get: 2 x Transceivers (Battery NOT included) 1 x Shutter release cable C3 1 x User manual      Prices:  All prices are in South African Rand (ZAR).    Returns:  60-day warranty period.    Shipping:  It normally takes approximately 7-18 working days (expect Public Holiday and Weekend) for arrival after receipt of a verified payment.   About Us: ECbidbuy is an international trading company who is fully committed to providing a convenient & secure one-stop shopping platform for customers in worldwide.    Contact Us:  Our office hour is 3:00am – pm (South African Time), Monday to Friday.   All questions will be replied within 48 hours.

Buy PCS YONGNUO RF C II FSK GHz Wireless Flash Trigger with C Shutter Connecting Cable... for R749.00

Buy YONGNUO RF C x Wireless Flash Trigger with x LS Shutter Connecting Cable for Canon Camera Black... for R909.00

SKU: -CALIRF603C1nnB    Features: Wirelessly and simultaneously control flash speedlites and strobe lights  On/Off camera wireless remote or just remote shutter release  2.4Ghz wireless frequency for optimum transfer speed, stability, and distance  Remote control distance of up to 100m (dependent on environment or area)  Interchangeable transceivers that can be used as receiver or transmitter  Radio Frequency: 2.4Ghz wireless  Transmitter Distance: up to 100m depending on area  Sync Speed: up to S  Channel: 15  Release: Half-way, Full-way press  Shutter Interface: 2.5mm socket  Strobe Light Interface: standard PC socket  Power Supply: 2 x AAA per remote (Not included)  Stand-by Time: >45 hours    Suitable for: Canon 60D, 300D, 350D, 400D, 450D, 500D, 550D, 600D, D    Packaged come with: 2 x Transceiver (Battery NOT included)  1 x Shutter release cable C1  1 x User Manual    Prices:  All prices are in South African Rand (ZAR).    Returns:  60-day warranty period.    Shipping:  It normally takes approximately 7-18 working days (expect Public Holiday and Weekend) for arrival after receipt of a verified payment.   About Us: ECbidbuy is an international trading company who is fully committed to providing a convenient & secure one-stop shopping platform for customers in worldwide.    Contact Us:  Our office hour is 3:00am – pm (South African Time), Monday to Friday.   All questions will be replied within 48 hours.

SKU: -CALIRF603N3nnB    Features: Wirelessly and simultaneously control flash speedlites and strobe lights  On/Off camera wireless remote or just remote shutter release  2.4Ghz wireless frequency for optimum transfer speed, stability, and distance  Remote control distance of up to 100m (dependent on environment or area)  Interchangeable transceivers that can be used as receiver or transmitter  Radio Frequency: 2.4Ghz wireless  Transmitter Distance: up to 100m depending on area  Sync Speed: up to S  Channel: 15  Release: Half-way, Full-way press  Shutter Interface: 2.5mm socket  Strobe Light Interface: standard PC socket  Power Supply: 2 x AAA per remote (Battery NOT included) Stand-by Time: >45 hours  Size: 37 x 30 x 81.5mm    Suitable for: Nikon D90 D D D D    Packaged come with: 2 x RF-603 Transceiver (Battery NOT included)  1 x Shutter release cable N3  1 x User Manual      Prices:  All prices are in South African Rand (ZAR).    Returns:  60-day warranty period.    Shipping:  It normally takes approximately 7-18 working days (expect Public Holiday and Weekend) for arrival after receipt of a verified payment.   About Us: ECbidbuy is an international trading company who is fully committed to providing a convenient & secure one-stop shopping platform for customers in worldwide.    Contact Us:  Our office hour is 3:00am – pm (South African Time), Monday to Friday.   All questions will be replied within 48 hours.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Instructions: 1. Clear: Press and hold the learning button for about 3 seconds, the LED will go out, flash 3 times after a while, clear OK. 2, learning the code: press the learning button, the LED lights up, release the learning button, enter the learning mode, press any button of the remote control at this time, transmit the signal, when you see the LED on the receiving module flashes 3 times, that is Indicates that the learning pair code is OK. 3. The remote control after learning can be controlled. Specifications: Working Temperature: -25~75C Frequency band: +-0.2MHz ReceiveDistance: 20-100M (open space) Receive Sensitivity: -108dB Working Frequency: 433MHz(Others can be customized) Quiescent Current: Working Voltage: DC3.3~5V Working mode:Point move, self-locking, interlocking Pin: GND: groud or negative pole +V: DC3.3~5V input D0: Data output D1: Data output D2: Data output D3: Data output VT: Output Precautions: 1. Do not operate with power. Turn off the power and operate it. After the test is confirmed, the power is turned on. 2. When using wireless electronic products, care should be taken to avoid strong interference sources such as metal masks, large electronic devices, and electromagnetic fields to prevent the modules from working properly. 3. Do not use this electronic product abnormally. Abnormal use will reduce product performance and longevity. In severe cases, damage to the product will also pose a safety hazard. Package Included: 5 x RX480E-4 433MHz Wireless RF Receiver 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output

Description: Note: This module does not suitable for IOS system. The core module HC-06 main modules, leads the interface includes VCC, GND, TXD, RXD, KEY pin high trigger to clear the pairing information re search led indicate Bluetooth connection status, flash unpaired slow flash indicates paired but not slave connection, Always follow machine connected Backplate settings LDO input voltage of 3.6~~6V unpaired current is about 30mA, paired 10mA, input voltage prohibit more than 7V absolute prohibition of reverse power! Interface level 3.3V, can be directly connected the various SCM (51, AVR, PIC, ARM, MSP430, etc.), the 5V MCU also can be connected directly, without MAX232 can not go through the MAX232! Open to effective distance of 10 meters, over 10 meters is also possible, but not of this the quality of the connection of the distance do to ensure The pair later when full-duplex serial use, do not need to know anything about the Bluetooth protocol, but only supports 8 data bits, 1 stop bit, no parity communication format, which is the most commonly used communication format does not support other formats. Support to establish a Bluetooth connection through AT commands set the baud rate, passkey, set parameters are saved after. Bluetooth connection is automatically switched to the pass-through mode. Wireless serial Bluetooth port with free extension cable. With transparent shrink tube, dust and beautiful, and there is a certain degree of anti-static capabilities. Size:3.57cm x 1.52cm Tips: TXD: the sender, usually expressed as its sender, the normal communication must be connected to another device RXD. RXD: the receive side, generally expressed as the receiving end of their normal communication to another device connected to TXD. Package included: 3 x HC-06 wireless bluetooth transceiver

Note: This module does not suitable for IOS system. Description: The core module HC-06 main modules, leads the interface includes VCC, GND, TXD, RXD, KEY pin high trigger to clear the pairing information re search led indicate Bluetooth connection status, flash unpaired slow flash indicates paired but not slave connection, Always follow machine connected Backplate settings LDO input voltage of 3.6~~6V unpaired current is about 30mA, paired 10mA, input voltage prohibit more than 7V absolute prohibition of reverse power! Interface level 3.3V, can be directly connected the various SCM (51, AVR, PIC, ARM, MSP430, etc.), the 5V MCU also can be connected directly, without MAX232 can not go through the MAX232! Open to effective distance of 10 meters, over 10 meters is also possible, but not of this the quality of the connection of the distance do to ensure The pair later when full-duplex serial use, do not need to know anything about the Bluetooth protocol, but only supports 8 data bits, 1 stop bit, no parity communication format, which is the most commonly used communication format does not support other formats. Support to establish a Bluetooth connection through AT commands set the baud rate, passkey, set parameters are saved after. Bluetooth connection is automatically switched to the pass-through mode. Wireless serial Bluetooth port with free extension cable. With transparent shrink tube, dust and beautiful, and there is a certain degree of anti-static capabilities. Size:3.57cm*1.52cm Tips: TXD: the sender, usually expressed as its sender, the normal communication must be connected to another device RXD. RXD: the receive side, generally expressed as the receiving end of their normal communication to another device connected to TXD. Package included: 1 x HC-06 wireless bluetooth transceiver

Description: Note: This module does not suitable for IOS system. The core module HC-06 main modules, leads the interface includes VCC, GND, TXD, RXD, KEY pin high trigger to clear the pairing information re search led indicate Bluetooth connection status, flash unpaired slow flash indicates paired but not slave connection, Always follow machine connected Backplate settings LDO input voltage of 3.6~~6V unpaired current is about 30mA, paired 10mA, input voltage prohibit more than 7V absolute prohibition of reverse power! Interface level 3.3V, can be directly connected the various SCM (51, AVR, PIC, ARM, MSP430, etc.), the 5V MCU also can be connected directly, without MAX232 can not go through the MAX232! Open to effective distance of 10 meters, over 10 meters is also possible, but not of this the quality of the connection of the distance do to ensure The pair later when full-duplex serial use, do not need to know anything about the Bluetooth protocol, but only supports 8 data bits, 1 stop bit, no parity communication format, which is the most commonly used communication format does not support other formats. Support to establish a Bluetooth connection through AT commands set the baud rate, passkey, set parameters are saved after. Bluetooth connection is automatically switched to the pass-through mode. Wireless serial Bluetooth port with free extension cable. With transparent shrink tube, dust and beautiful, and there is a certain degree of anti-static capabilities. Size:3.57cm x 1.52cm Tips: TXD: the sender, usually expressed as its sender, the normal communication must be connected to another device RXD. RXD: the receive side, generally expressed as the receiving end of their normal communication to another device connected to TXD. Package included: 5 x HC-06 wireless bluetooth transceiver

Features: Easy to install and easy to carry With a slidable cover on the remote control With a hook on the remote control Use Learning coding, stable and reliable The wireless signal can pass through walls, floors and doors You can turn on or turn off the receiver with transmitter (remote control) from any place within a reliable distance Operating Voltage: DC12V Maximum Load: 10A Operating Frequency: 433MHZ (in set) Receiver Sensitivity: -100dBm Encoding Type: learning code Board Size: Approx. 5.3x3.1cm/ 2.09x1.22" Output Working Way: 1. Jog: Pressing one button is working. Loosing your finger on the same button is stop. (need one channel switch and one buttons remote control) 2. Self-lock: Pressing one button for one time is working. Pressing the same button again is stop (need one channel switch and one buttons remote control) 3. Inter-lock: Pressing one button is working. Pressing another button is stop (need one channel switch and 2 buttons remote control) 4. Please notice that here is 1CH and 1 button wireless remote control. You can choose the self-lock or jog working/ output way, you better choose jog or self-lock, so pressing the button is open, and pressing again is close, or pressing is open, and loosing finger is close Learning and Remove Method: 1. Press the learning code. The indicator from on to off, loosen your finger, press any button of the remote control, the indicator flash 2 times and off. It mean you learn it successfully 2. It can learn more than 12 PCS 2262 or 1527 chip with the different code wireless remote control 3. Remove/ Clean: Press the learning button about 8 seconds, the indicator turn on to off, it means the information that you keep have been removed successfully Package Included: 3 x Learning Code Receiver 3 x Remote Control

The best value in guitar wireless systems! Easy to set up and operate, at a price that can't be beat! The Nady DKW-1 GT is a cost effective VHF wireless Guitar / Instrument system. It's easy to use and only takes a few minutes to set up. Delivering clear, transparent, high-fidelity audio, the DKW-1 GT systems can be used with a broad range of instruments with an audio output, including electric guitar, bass and other instruments with pickups. It features an advanced audio processing circuitry for a wide dynamic range - no overloading for loud inputs or background hiss during quiet use. This system comes complete with everything you need to plug in to a PA or guitar amplifier... including a connecting ¼"- to - ¼" audio cable. Just install a fresh battery (not included) in the bodypack, connect the AC adapter to the receiver and to a power outlet, turn it on, and you are done! This affordable and reliable system couldn't be easier to set up and to use! SPECIFICATIONS: Overall: Frequency Response: 40Hz-20kHz (±3dB) RF Carrier Frequency Range: 170-216MHz Operating Range: 250 ft. typical operating range, up to 500+ ft. line-of-sight Transmitter: Audio Input: 3.5mm locking jack for included instrument cable Controls: Off/Standby/On switch LED Indicator Unit: "ON" (single flash), Low Battery Alert (steady) Battery: 9V Alkaline Battery Life: Up to 15 hours Receiver: Controls: Power ON/OFF Connectors: 1/4" unbalanced audio out jack, DC input jack LED Indicator: Power ON, Transmitter ON, Audio Peak   SPECIFICATIONS All the advantages and freedom of wireless operation without cumbersome cords: Includes a wireless bodypack and a receiver - Great system for live performance, rehearsal or recording Operates on a single channel in the high-band VHF range (170-216 MHz) for reliable, interference-free performance, and excellent high-fidelity audio. 250+ ft. typical operating range - up to 500+ ft. line-of-sight Included WGT wireless bodypack provides easy operation with On/Standby/Off switch and low-battery LED indicator which flashes once for "Unit On" and lights steady for low-battery alert. Standby position allows easy muting with the transmitter on Bodypack provides easily accessible Input Level Adjust for optimum sound, and up to 15 hours of wireless operation on a single 9V alkaline battery. Locking 3.5mm mini-jack provides secure connection for removable instrument cable DKW-1 mini portable receiver with unique space-saving, vertical design and power ON/OFF switch, ¼"audio output jack, and easily visible extra-jumbo LED indicators for power on, transmitter on and audio peak. Comes with a one year warranty from Blueridge Music(authorised Nady dealer in SA) Shipping is R125 ANYWHERE in SA  

The best value in wireless systems! Easy to set up and operate, at a price that can't be beat! The Nady DKW-8U HT is a cost effective UHF wireless handheld microphone system. It's easy to use - simply plug in instead of your wired microphone. Delivering clear, transparent, high-fidelity audio, the DKW-8U HT system can be used for a broad range of singing and speaking applications, karaoke and recreational singers, DJ's, auctioneers, teachers, aerobics instructors, clergy, and a host of others. It features an advanced audio processing circuitry for a wide dynamic range - no overloading for loud inputs or background hiss during quiet use. This system comes complete with everything you need to plug in to a PA... including a connecting ¼"- to - ¼" audio cable. Just install a fresh battery (not included) in the microphone, connect the AC adapter to the receiver and to a power outlet, turn it on, and you are done! This affordable and reliable system couldn't be easier to set up and to use! SPECIFICATIONS: Overall Performance: Frequency Response: 905.800MHz-949.800MHz, ±3dB Dynamic Range: 120dB Total Harmonic Distortion RF Carrier Frequency Range: UHF Frequency Stability: ±0.005%, crystal controlled Modulation: FM ±20kHz normal Operating Range: Up to 250 ft. typical; up to 500+ feet optimum line-of-sight Receiver: Squelch: Fixed Controls: Volume Control Connectors: DC In: (2.1mm barrel), Unbalanced Out: ¼" (6.3mm) jack LED Indicators: Power ON, Signal, AF LEDs Unwanted Signal Rejection: 60dB image and spurious Antenna: 4", Single section telescopic Transmitter: Audio Input: Nady DM-10D neodymium dynamic cartridge Controls: ON/STANDBY/OFF RF Power Out 20mW Harmonic and Spurs Indicators: Single LED, flash once "ON", LOW BAT "Steady ON"   Shipping is free  anywhere in SA Comes with a one year warranty

The WiFi Display Receiver is a Special Devices to project your Smart Phones / Tablet PC / Notebook to another big screen devices with HD interface (such as, HDTV, Monitor & Projector, etc) through WiFi connection. And, it Supports Popular standards, such as, Miracast, DLNA,can enhance your HDTV / Projector / Monitor with HD input socket. Moreover, The MiraScreen has more features such as, streaming video, web surfing, photo viewer, Internet video and more, just to enjoy excellent multi-display sharing.Ultra low power consumption, and low heat.With compact portable deign for easy carrying.    Description:  1. Color: Black, Gold 2. Interface: 1x HD 1.4; 1x Micro USB  3. OS and OS-Version / Release: Linux  4. CPU-Version / Processor: AM8258  5. CPU Speed: 600MHZ  6. RAM (MB): DDR3 128MByte 7. Internal Flash (MB): 16MB  8. Max. Resolution: (1920*1080_30P)    9. USB: USB 2.0  10. Output: HDMI  11. Wifi Module/Version: 8188FTV  12. Wifi Frequncy: 2.4G  13. RF / Antenne: External 14. Video Formats: avi /.divx /.mkv /.ts /.dat /.vob /.mpg /.mpeg /.mov /.mp4 /.rm /.rmvb /.wmv 15. Picture Formats: JPEG, BMP 16. Audio Formats: MP1, MP2, MP3, WMA, OGG, ADPCM-WAV, PCM-WAV, AAC  17. Voice Record:.mp3/.wav  18. File Formats: Dobe PDF, MS Word, Ms Excel, Ms Powerpoint, I Works  19. Bluetooth: N/A 20. DLNA: Standard  21. ScreenShare: Miracast, airplay, DLNA  22. Power: DC 5V/1A  23. Switchover-free: No  24. Cell phone System Support: IOS 8.0+, Android 4.2+   Please Pay Attention: Note 1: Please make sure that your smart phone and Tablet PC support Miracast, DLNA, Airplay function before you buy it. Note 2: The WiFi Wireless Display Receiver is not compatible with Windows OS. Note 3: The WiFi Wireless Display is only compatible with Smart phone and Tablet PC, not compatible with PC. Note 4: The WiFi Wireless Display Receiver is not compatible with Netflix, Amazon Video Client, HBO go, Honda Motor. Note 5: The distance between your Smart Phone / Tablet PC and the WiFi Wireless Display Receiver should be within 6 meters to ensure better transmission effect. Note 6: Please place the external WiFi Module in front of your TV, make sure that there is no obstacle between the WiFi Module and your Smart phone / Tablet PC. Note 7: MiraScreen New Wireless Display Receiver is not Google Chromecast 2. Packing Listing: 1x Wireless WiFi Display Receiver 1x USB with WiFi 2 in 1 Cable  1x Instruction 1x Gift Box