Led psu driver

Buy ENCLOSED LED PSU / DRIVER IN=220V OUT=56V 1.4A 80W SLD-80-56 for R510.80

Buy ENCLOSED LED PSU C.C. DRIVER I=220 O=48V 2A ELG-100-48A for R1,075.66

    Feature Input Voltage AC/DC12V Output Current: 320 - 350mA Can power 4-7pcs 1W power LED High efficiency   Application Flashlight driver Backlight driver PowerLED which have only small space to install           Copyright notice: All material on this listing is copyright of Improved Living. Duplication or sale of all or any part of it is not permitted LED strip light strips for 12V DC not 220V AC Switch light bright control controller dimmable dimmer mA Amp Amps Volt Volts decorative mood 12vdc DC12V fish tank fishtank coral growth grow light plant tank rigid cupboard kitchen counter camp clamp m meter 20000k kelvin wave length flood light floodlight spot light out door outdoor security safe safety solar emergency  load shedding back up backup transformer AC to DC power converter driver voltmeter volt meter am meter non waterroof  coating

  Feature Input Voltage AC/DC12V Output Current: 320 - 350mA Can power 4-10pcs 1W power LED High efficiency   Application Flashlight driver Backlight driver PowerLED which have only small space to install          Copyright notice: All material on this listing is copyright of Improved Living. Duplication or sale of all or any part of it is not permitted

Led Driver 6-12V 400mA (Waterproof): Input Voltage: 220V AC Output Voltage: 6-12V DC Output Current: 400mA Size: 45x30x23mm These drivers are unused, removed from 10W floodlights, sold as secondhand For less heat produced by led, this driver can be used to underpower: 3x3W leds (connected in series) or 1x 10W led at 400mA    

 LED Dimmer Great for  12V DC LED Strips. NO more switches only remote BATTERY NOT INCLUDED PLEASE SEE SHIPPING TAB FOR ALL YOUR SHIPPING OPTIONS Also available items: LED chips, driver, Power supplies, etc.     Copyright notice: All material on this listing is copyright of Improved Living. Duplication or sale of all or any part of it is not permitted

LED POWER SUPPLY / DRIVER; IP67 I=UNIV; O=21-26VDC; CC; @ 6.7-13.3Amps; VOLTAGE & CURRENT ADJUSTABLE

LED POWER SUPPLY / DRIVER; IP67 I=UNIV; O=21-26VDC; CC; @ 6.7-13.3Amps; VOLTAGE & CURRENT ADJUSTABLE. WITH 3-IN-1 DIMMING

LED CONSTANT CURRENT POWER SUPPLY I=90-264VAC / UNIVERSAL; O=9-24VDC; I=1.05A;

LED Driver Charging Constant Current Voltage Step Down Buck Module Feature: This module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable. This module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV! This module uses machine placement, reflow soldering. This module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V. Module indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module. Description: Nature of the module: Non-isolated step-down module Rectification: Non-synchronous rectification Input voltage: 7V - 35V Output voltage: 1.25V - 30V Output current: Adjustable, 3A (maximum) Transfer efficiency: 92% (maximum) Switching frequency: 150KHz output ripple: 50mV (maximum) 20M Kbps Load regulation: ±0.5% Voltage regulation: ±2.5% Operating temperature: -40°C to +85°C Dimension: 48 x 23 x 14mm (L x W x H) Battery charging method: 1. Make sure the battery float voltage and charging current, the module input voltage; 2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value; 4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment) 5. Adjustment constant potentiometer allows the output voltage reaches the float voltage; 6. Connected to the battery and try to charge. (1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.) LED constant current driver using method: 1. Make sure that the drive LED operating current and maximum working voltage; 2. Adjustment constant potentiometer, output voltage adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current; 4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED; 5. Connect LED, test machine. (1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.) Package included: 1 x Buck module

LED POWER SUPPLY; CONSTANT CURRENT; SHORT PROTECTED; IP30 IC=2A; VO=18~30V

Led Driver for (14-18) x 3W Leds: Forward Voltage: 42-68V Forward Current: 600mA Non Waterproof: Yes Open/ Without Cover: Yes  

Led Driver 1W for (1-3) 1W Leds 12V-24V MR16: Input Voltage: DC 12-24V Output Current: 300mA Output Voltage: DC 9-12V

Led Driver 3W for (1-3) 3W Leds 12V-24V MR16: Input Voltage: 12-24V DC Output Voltage: 3 - 12V DC Output Current: 600mA Power: 3W Can be used to: Connect 1, or 2, or 3 Leds in series (3W Leds)

Buy PSU ENC LED DRIVER I=220 O=18-36 5A ELG-200-36 for R1,113.38