Led driver power

Buy Replacement LED Driver | Power Converter for LED Floodlight for R129.00

LED Driver Charging Constant Current Voltage Step Down Buck Module Feature: This module uses the LM2596 chip, high efficiency (up to 92%), low heat, can be very easily used to above 3A current, in conjunction with the original TI op amp control output current, so the overall output is very stable. This module uses the original Sanyo low ESR filter capacitor, you can make low ripple voltage to 50mV! This module uses machine placement, reflow soldering. This module is an adjustable buck module, the module can be adjusted from the blue adjustable resistor to change the output voltage. Input and output differential pressure is 2V, the minimum can be output 1.23V. Module indicated IN - (negative input), IN + (positive input), OUT - (negative output), OUT + (positive output), please note must be correct connected, otherwise may cause damage to the module. Description: Nature of the module: Non-isolated step-down module Rectification: Non-synchronous rectification Input voltage: 7V - 35V Output voltage: 1.25V - 30V Output current: Adjustable, 3A (maximum) Transfer efficiency: 92% (maximum) Switching frequency: 150KHz output ripple: 50mV (maximum) 20M Kbps Load regulation: ±0.5% Voltage regulation: ±2.5% Operating temperature: -40°C to +85°C Dimension: 48 x 23 x 14mm (L x W x H) Battery charging method: 1. Make sure the battery float voltage and charging current, the module input voltage; 2. Adjustment constant potentiometer, the output voltage is adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjust the constant current potentiometer make the output current reaches a predetermined charge current value; 4. Turn lamp current default is 0.1 times charging current (constant current value), if you need to adjust please adjust the turn lamp current potentiometer; (generally doesn't need adjustment) 5. Adjustment constant potentiometer allows the output voltage reaches the float voltage; 6. Connected to the battery and try to charge. (1,2,3,4,5 steps are for the module input connected to the power supply, output-load battery is not connected.) LED constant current driver using method: 1. Make sure that the drive LED operating current and maximum working voltage; 2. Adjustment constant potentiometer, output voltage adjusted to about 5V. 3. Use the multimeter (10A current) measuring the output short-circuit current, meanwhile adjusting the constant current potentiometer allows the output current reaches a predetermined LED working current; 4. Adjustment constant potentiometer allows the output voltage reaches the maximum operating voltage LED; 5. Connect LED, test machine. (1,2,3,4 steps are module input connect to the power supply, output-load is not connected LED lights.) Package included: 1 x Buck module

Led Driver 6-12V 400mA (Waterproof): Input Voltage: 220V AC Output Voltage: 6-12V DC Output Current: 400mA Size: 45x30x23mm These drivers are unused, removed from 10W floodlights, sold as secondhand For less heat produced by led, this driver can be used to underpower: 3x3W leds (connected in series) or 1x 10W led at 400mA    

Buy POWER SUPPLY ENCL. LED DRIVER IN=220V O=95-240VDC 4.2A 1000W HVGC-1000A-M-AB for R6,457.86

Buy POWER SUPPLY LED DRIVER I=220 O=24V 0.8A 20W PLN-20-24 for R601.00

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=36 0.5A 20W PLN-20-36 for R283.84

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=6-48V 0.35A 18W LPHC-18-350 for R253.85

Buy Power Supply Lighting Transformer LED Driver for Strip Light for R345.00

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=71-143V 1A4 HLG-185H-C1400B for R1,419.35

Buy POWER SUPPLY ENCL. LED DRIVER CV I=220V O=15V 1A 15W APV-16-15 for R225.86

Buy POWER SUPPLY ENCL. LED DRIVER I=220V O=36V 3.4A 120W NPF-120-36 for R1,335.90

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=143-286 0A7 200W HLG-185H-C700A for R1,591.06

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=42-72 0.35A 25W PLM-25-350 for R393.44

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=24 0.75A 18W LPH-18-24 for R247.69

Buy POWER SUPPLY ENCL. LED DRIVER IN=220V OUT=12 6.6A 80W SLD-80-12 for R510.80

Buy POWER SUPPLY ENCL. LED DRIVER I=220 O=5 12A 100W LPV-100-5 for R555.78

3-4 x 3W Driver Driving power: 3-4X3W Input Voltage: 85V~277V Output Voltage: 8-14V Current:600mA Efficiency > 95% Power Factor >0.98 Operating Temperature: -20~80 Size (L * W * H): 56mm * 32mm * 21mm

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 3 x 8A 300W buck adjustable power supply module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 5 x 8A 300W buck adjustable power supply module