Led driver 3w

Buy LED Driver 3W 12V (1-3Led) 600mA MR16 **LOCAL STOCK** for R25.00

Buy LED Driver 3W (10-18 Leds) 30-60V 600mA Open **LOCAL STOCK** for R120.00

Led Driver 3W for (1-3) 3W Leds 12V-24V MR16: Input Voltage: 12-24V DC Output Voltage: 3 - 12V DC Output Current: 600mA Power: 3W Can be used to: Connect 1, or 2, or 3 Leds in series (3W Leds)

Led Driver for (14-18) x 3W Leds: Forward Voltage: 42-68V Forward Current: 600mA Non Waterproof: Yes Open/ Without Cover: Yes  

Led Driver 6-12V 400mA (Waterproof): Input Voltage: 220V AC Output Voltage: 6-12V DC Output Current: 400mA Size: 45x30x23mm These drivers are unused, removed from 10W floodlights, sold as secondhand For less heat produced by led, this driver can be used to underpower: 3x3W leds (connected in series) or 1x 10W led at 400mA    

1-3 X 1W LED Driver Wattage¿1-3W Input Voltage¿ 12V  Output Voltage¿DC 2.5-3.6V  Output Current¿300MA

  1-3 X 1W LED Driver Size¿ 26mm(L) x12mm(W)x 14mm(H) Wattage¿1-3W Input Voltage¿ AC 85-265V 50/60Hz Output Voltage¿DC 3-11V  Output Current¿300MA

10-18 x 3W  Driver Quantity: 1pcs Input Voltage: AC85-277V 50/60Hz Output Voltage: DC36-60V Output Current: 600mA ±5% can work for 12-18pcs 3W led chip n series connection Dimension: (L) 115mm*(W)45mm*(H)28mm

3-4 x 3W Driver Driving power: 3-4X3W Input Voltage: 85V~277V Output Voltage: 8-14V Current:600mA Efficiency > 95% Power Factor >0.98 Operating Temperature: -20~80 Size (L * W * H): 56mm * 32mm * 21mm

3 X 3W LEDs Input voltage: 12v Output voltage: 9-11v Current: 600mA  ±5%  

Description: NOTE: step-down mode, Inputs must be higher than the output above 2V-3V. Instructions: IN+: Positive electrode of power supply IN-: Negative electrode of power supply. LED+: Anode for LED LED-: Cathode connected to LED PWM: Dimming control signal (2.8V-6V) PWM signal limit frequency: 20HZ-20KHZ Rated recommendations: About 1KHZ Package included: 5 x RUIDENG 3W LED Driver

Buy 10Pcs RIDEN 3W LED Driver Supports PWM Dimming IN 7-30V OUT 700mA for R439.59

Buy RIDEN 3W LED Driver Supports PWM Dimming IN 7-30V OUT 700mA Module for R229.00

Buy 10pcs 3W 5-35V LED Driver 700mA PWM Dimming DC to DC Step-down Module Constant Current Dimmer Contro for R455.00

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 3 x 8A 300W buck adjustable power supply module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ￢ﾀﾋ 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.￢ﾀﾋ 2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ￢ﾀﾋ Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 5 x 8A 300W buck adjustable power supply module

Specifications: · 300W 8A 7-32V to 0.8-28V DC CC CV Buck Step-Down Converter Power Supply Step Down Module Adjustable Voltage Regulator LED Driver · High-power, constant current LED driver · Battery charger · Vehicle-mounted power supply · Low voltage system power supply · Non-isolated step-down CC CV Buck module with on-board LED load indicator · Input voltage: DC 7-32 V · Output Voltage: DC 0.8-28 V (Adjustable) · Output Current: 8A (MAX), more than 60Deg please strengthen heatsink · Continuous Current Range: 0.2-8A Adjustable · Output Power: 300W (MAX) · Conversion efficiency: 95% (more input voltage, more efficiency) · Output ripple: 50mV · Working Temperature: industrial (- 40 ° c to +85 °c) (environmental temperature, more than 40 degrees, please reduce power to use, or - enhance cooling) · No-load current: 20mA (input 24V,Output 12V for reference) · Voltage regulation: ± 1% · Load regulation: ± 1% · Dynamic response speed: 200uS 5% · Short circuit protection: YES · Input Reverse protection: No (please comply with a reverse protection or connect a diode at input parts.) · Size: 65 x 47 x 22 mm · On-board LED load indications: red = load present (eg. 'battery charging'), green = no load (eg. 'battery charged' or output disconnected) Features: 1. Fixed turn lamp current is 0.1 times the current value(Used to identify whether the battery is fully charged When charging). 2. Made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%). Particularly suitable for LED driver. 3. High output current, the max output current can reach 8A. 4. Four high frequency capacitance, can lower output ripple, enhance the work stabilization. 5. Double heat sink design. MOS schottky diode independent heat sink,which heat dissipation is good, and won't affect each other. 6. Using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever. 7. 3296 multiturn potentiometer,high accuracy voltage and current regulation, good stability. 8. Double color lamp, working condition be clear at a glance 9. Voltage and current are adjustable,wich effect is good. Applications: 1. High-power LED driver. 2. Lithium battery(or lead accumulator) charge. 3. Vehicle-mounted power supply. 4. Low voltage system power supply. 5. 6V, 12V, 14V, 24V battery charge. 6. On-board laptop power supply. 7. regulated power supply. 8.Low voltage power supply system. Module adjustment: ??br /> 1. When the module output voltage can not be adjusted (the output voltage is always equal to the input voltage) Please adjust the potentiometer counterclockwise 20 laps (20 turns) or more till it works.??br />2. Turn trimmers CLOCKWISE to INCREASE, ANTICLOCKWISE to DECREASE. 3. When adjust the blue potentiometer,please use a multimeter to monitor the voltage 4. The trimmer nearest the voltage output adjusts the output CURRENT (CC) 5. The trimmer nearest the voltage input adjusts the output VOLTAGE (CV) Charger application - intructions: 1. First determine the float voltage and charging current required by the battery to be charged (the ‘target battery'). The target battery disconnected from the module output, apply a voltage of 7V - 32V to the module input, being sure to observe correct polarity. 2. Using the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the charging current required by target battery. 4. Using the CV trimmer, adjust the module's output voltage to the float voltage required by the target battery. 5. Connect the target battery to the module output, observing correct polarity. Charging of the battery should commence ??br /> Constant current LED Driver Application - Instructions: 1. First determine the operating current and maximum operating voltage of the LED you need to drive. 2. With the CV trimmer, adjust the output voltage to about 5V. 3. Switch your multimeter into its 10A current scale and measure the module's short-circuit output current. Turn the CC trimmer to adjust the current to the operating current of your LED. 4. Adjust the CV trimmer to make the output voltage reach the maximum LED operating voltage. 5. Connect LED, test. Package included: 3 x 8A 300W buck adjustable power supply module