Tork craft diamond core

Buy Tork Craft Diamond Core Bit 64mm For Tiles Hex Shank for R360.53

Buy Tork Craft Diamond Core Bit 52 X 170mm Universal Purpose M22 for R1,239.70

Buy Tork Craft Diamond Core Bit 76mm For Tiles Hex Shank for R493.35

Buy Tork Craft Diamond Core Bit 76Mm For Tiles Hex Shank for R423.00

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø12.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø16mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø8mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø38mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø19mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø14mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø30mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø6mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø20mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø40.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø5mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø22mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø65mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø117mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill Set Core drills in the set: Ø38mm Ø52mm Ø65mm Ø117mm The set also includes: (x1) drift key (x1) Pilot drill bit (x1) 70mm Hex adaptor (x1) 70mm SDS Plus adaptor (x1) 200mm Hex adaptor (x1) 200mm SDS Plus adaptor Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. Core diameter: Ø52mm Depth: 170mm Adaptor thread: M22 Main use: Concrete Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in concrete for an installation. Core diameter: Ø38mm Depth: 170mm Adaptor thread: M22 Main use: Concrete Application: The dry cut diamond core drill is designed to be used without water to drill into: Concrete Concrete pipes Brickwork Roof tiles Slate Stone Paving Tarmac It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.

Dry Cut Diamond Core Drill For plumbers, electricians or general contractors needing to drill a hole quickly and cleanly in brickwork for an installation. Core diameter: Ø52mm Depth: 170mm Adaptor thread: M16 Main use: Brickwork Application: The dry cut diamond core drill is designed to be used without water to drill into: Brickwork Roof tiles Slate Stone Paving It allows the user to drill neat and clean holes quickly without the setup an cleanup time associated with using a water-cooled drilling jig. INFORMATION: Have a look at the different adaptors under the EXTRA INFO tab and the complete range under the ACCESSORIES tab. IMPORTANT: Not for reinforced drilling! Use a wall scanner to detect reinforcing, water pipes or electrical conduit.