Tmc2130 motor driver module

Buy TMC2130 V1.0 Stepper Motor Driver Module w Heat Sink & Screwdriver for 3D Printer... for R509.00

Semiconductor BTS7960B 43A H-Bridge Motor Driver Module For Arduino Features: Double BTS7960 huge electric current (43A) H bridge driving 5V isolated from SCM so it can protect the SCM effectively This module can effect motor forward and reversal, both PWM highest frequency is 25kHz Two streams passing overheating error signal will be put out. Power supply of isolating chip is 5V so it can be used with SCM in 5V Pressure of electric current ranges from 5.5V--27V Specification: Weight: 66g Size: 4.8 x 4.8 x 3.9cm Package included: 1 x BTS7960B motor driver

Buy 3pcs L298N Motor Driver Module Four Chaneel Motor Drive Smart Car Module for R388.37

Buy L298N Motor Driver Module Four Chaneel Motor Drive Smart Car Module Geekcreit for Arduino - products for R327.00

Buy 5V STEPPER MOTOR DRIVER MODULE + STEPPER MOTOR KS0140 for R158.80

High Power MOS Tube DC Motor Driver Module L298N/H Bridge Drive / Support PWM PPM Signal Package contains 1 X item of the smallest listed variant.

Buy 5pcs DRV8833 2 Channel DC Motor Driver Module Board 1.5A 3V-10V for R251.55

Buy L298N V3; 4-DC STEPPER MOTOR DRIVER MODULE MD0225 / 18---- for R253.00

Buy High Power MOS Tube DC Motor Driver Module L298N/H Bridge Drive / Support PWM PPM Signal for R491.73

Buy 3A 75W DC PWM Speed Adjustable Motor Driver Module LMD18200T Geekcreit for Ardu for R280.00

FULL BRIDGE MOTOR DRIVER FOR DC SERVO MOTORS AND GEAR MOTORS; 36V; 30A; PWM INPUT FOR SPEED CONTROL - 5V ARDUINO BOARD COMPATIBLE

DC MOTOR DRIVER; BB-L298 is dual full bridge driver with up to 2.5A and 7-40V.

3D Printer A4988 Reprap Stepping Stepper Step Motor Driver Module Description: A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power sequencing. A4988 surface mount QFN package (ES), a size of 5 mm × 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin leadframe plating. Feature: Simple step and direction control interface Short-to-ground and shorted-load protection Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above       your stepper motor’s rated voltage to achieve higher step rates Package included: 1 x Step motor driver module 1 x Heatsink

Features: 1.Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motors 2.Built-in TSD, without worrying about motor stall 3.Ultra-small size, suitable for assembly and car Specification: 1.Module supply voltage: DC 2V-10V 2.Signal input voltage: DC 1.8-7V 3.Single working current: 1.5A 4.Peak current up to 2.5A 5.Low standby current (less than 0.1uA) 6.Built-in common conduction circuit, the input terminal vacant, the motor does not malfunction 7.Size: 24.7 x 21 x 7mm 8.Mounting hole diameter: 2 mm Package included: 3 x Mini dual channel DC motor driver module

Description L9110 Motor Drive Module | L9110 / Motor Drive Module L9110 Motor Drive Module Specifications L9110S -Chip Motor Driver Module Supply Voltage: 2.5-12V Suitable Motor Range: Motor Operating Voltage 2.5v-12V and the Maximum Operating Current of 0.8A, smart car Currently Available Voltage and current are within this range can drive two DC motors, or a 4-wire two -phase stepping motor. PCB Board Size: 2.8cm x 2.1cm ultra-small size, suitable for assembly provided with fixing holes, diameter: 3mm Module Interface Description 6P Black Bent Pin Description 1 VCC external 2.5V-12V voltage External GND 2 GND 3 IA1 external microcontroller IO port 4 IB1 external microcontroller IO port 5 IA2 external microcontroller IO port 6 IB2 external microcontroller IO port Green Terminal Description [4P] 1 OA1 OB1 pick DC motor 2 pin, no direction 2 OA2 OB2 pick DC motor 2 pin, no direction Module for use ON VCC, GND module power indicator light IA1 input high, IA1 input low, [OA1 OB1] motor is transferred; IA1 input low, IA1 input high, [OA1 OB1] motor reversal; More Information View More Information More Products View More Products