A4988 drv8825 motor driver

CNC Shield Board + 4Pcs A4988 Stepper Motor Driver For Arduino 3D Printer

Buy SIMAX3D 6Pcs A4988 Stepper Motor Driver Board Red with Heatsink for 3D Printer for R261.19

Buy SIMAX3D 6Pcs A4988 Stepper Motor Driver Board Red with Heatsink for 3D Printer for R349.00

Description: 1. For  A4988 / DRV8825 2. Jumpers are hit on the DP position represents 16 segments (4988) or 32 segments (8825). 3. Jm connected to the motor. 4. Jv connect 5V and 12V-24V power supply 5. Jc E / S / D / G corresponding to the connection on the Enable Step Dir Gnd drive signal output. 6. Size: 34x41mm Note: Note the direction of the installation, or may burn the driver or even the motherboard. Package Included: 1 x Stepper Motor

Descriptions: 1.If jumper is hit the position of ON DP,that means 16 segment (4988) or 32 segment (8825)Jm connected motor 2.Jv connect 5v and 12v-24v power supply 3.Jc E, S, D, G, respectively corresponding to the connection of the Enable/Step/Dir/Gnd drive signal output Package Included: 1x A4988/DRV8825 Stepper Motor

Buy A4988 DRV8825 Stepper Motor Control Board Expansion Board For 3D Printer... for R169.00

3 Axis USB CNC Arduino Nano Controller A4988 Stepper Motor Driver Board

Buy TWO TREES CNC Shield + UNO R3 Board +4x A4988 Stepper Motor Driver +4x 4401 for R1,159.28

Geeetech Ultra-quiet TMC2208 Stepper Motor Driver + Heatsink + Screwdriver Kit Package weight: 0.03 kg TMC2208 is a single-axis, ultra-quiet stepping motor driver chip, power tube built-in drive current 1.4A peak current 2A, voltage range 4.75V-36V, 256 subdivision.StealthChop2 - faster motor acceleration/deceleration than stealthChop.Automatic stealthChop and spreadCycle switchover depending on the velocity UART configuration interface (9600...500k Baud), flexible microPlyer interpolation unit provides up to 256 subdivisions, allowing perfect sinusoidal control even in systems with limited pulse frequencies; faster motor acceleration/deceleration than stealthChop, these are also designed because stealthChop2 ultra-quiet technology is widely applied to 3D printing. This TMC2208 Stempstick can replace the original TMC2100 A4988 DRV8825 LV8729. Plug and play, no wiring required. Package Included: 1 x TMC2208 Driver 1 x Heat Sink 1 x Screwdriver Click here for more deals Geeetech Ultra-quiet TMC2208 Stepper Motor Driver + Heatsink + Screwdriver Kit Geeetech Ultra-quiet TMC2208 Stepper Motor Driver + Heatsink + Screwdriver Kit

Description: A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power sequencing. A4988 surface mount QFN package (ES), a size of 5 mm 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin leadframe plating. Features: 1. Simple step and direction control interface 2. Short-to-ground and shorted-load protection 3. Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step 4. Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 5. Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection 6. Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above       your stepper motors rated voltage to achieve higher step rates Package included: 2x Step motor driver module 2x Heatsink

Geekcreit 3D Printer Stepstick DRV8825 Stepper Motor Driver Reprap 4 Layer PCB

10X Geekcreit CNC Shield + UNO R3 Board + 4x A4988 Driver Kit With Heat Sink Fo Package weight: 0.94 kg - CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Package included: 10 x CNC Shield + UNO R3 Board + 4x A4988 Driver Kit Click here for more deals 10X Geekcreit CNC Shield + UNO R3 Board + 4x A4988 Driver Kit With Heat Sink Fo 10X Geekcreit CNC Shield + UNO R3 Board + 4x A4988 Driver Kit With Heat Sink Fo

MKS RUMBA Motherboard + 6x TMC2130 Driver Kit for 3D Printer FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: Using the same CPU as Arduino Mega, Atmega2560 as the main control chip, together with high-performance USB chip Atmega16U2, to achieve compatibility with all Ramps-related firmware. 5 temperature sensor interface input. All pins are drawn out to facilitate more functional expansion. With LCD extension interface, it can connect SD extension version of Chinese LCD screen to realize offline printing (support 2004 and 12864). Extended interface of steering gear to add automatic leveling function conveniently. Support 6 A4988 DRV8825 TMC2208 TMC2130 TMC2100 and other driving boards. PWM DC output (heating tube, fan, etc.): 6 output (1 high current, 3 medium current, 2 low current) are driven by high performance low conduction resistance MOS transistors, each output is indicated by LED. Power supply part: power input is 12V-35V, dual power supply design, effectively avoiding mutual influence. Hot bed part supports 11A current, 12V, other parts of the circuit, 5A, 12V. In order to reduce the high temperature caused by high current on Mega Controller board, it is suggested to add 12V heat dissipation fan. The firmware of control panel will adopt Marlin, which is the most widely used nowadays. It has good performance in stability, ease of use and functionality. The circuit board is specially designed for CNC processing such as 3D printer, engraving machine and laser cutting machine. A personal computer can be used to control a 3D printer through a USB connection or to print directly from an SD card. Because of the integrated design, simple installation and debugging, and the common Arduino IDE as the development software, firmware upgrade, parameter configuration is simple and easy to use. The single-phase current of the two-phase stepping motor is 1.2A (peak 2.5A) and the working current of the motor is adjustable. Support two control modes of Step/DIR interface and SPI interface. Combination of maximum efficiency and optimal motor torque operation without noise. High-precision sensorless motor load detection. Reduce energy consumption by 75%. High-load drivers will not be out of step. Interface: Step / Dir or SPI Configuration: CFG pin or SPI Segmentation: up to 1/256 microPlyer microsteps 1/256 Logical Voltage VIO: 3-5V Motor Voltage VM: 5.5-46V Motor Phase Current: 1.2A RMS, 2.5A Peak Package included: 1 x Motherboard 1 x USB Cable 6 x TMC2130 Driver 6 x Cooling Rib 1 x Black screwdriver MKS RUMBA Motherboard + 6x TMC2130 Driver Kit for 3D Printer MKS RUMBA Motherboard + 6x TMC2130 Driver Kit for 3D Printer MKS RUMBA Motherboard + 6x TMC2130 Driver Kit for 3D Printer

3D Printer Controller RAMPS 1.4: The RepRap Arduino-compatible MEGA Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Features: USB type B receptacle. SD Card add on available. Fits 5 Pololu stepper driver board. LEDs indicate when heater outputs on. Expandable to control other accessories. Heated bed control with additional 11A fuse. Option to connect 2 motors to Z for Prusa Mendel. I2C and SPI pins left available for future expansion. It has provisions for the cartesian robot and extruder. All the Mosfets are hooked into PWM pins for versatility. 3 mosfets for heater / fan outputs and 3 thermistor circuits. Fused at 5A for additional safety and component protection. Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs. Servo style connectors are used to connect to the endstops, motors, and leds. These connectors are gold plated, rated for 3A, very compact, and globally available. Arduino-Compatible Mega 2560 R3: Fully compatible with original Arduino MEGA 2560 R3, with this product, you are able to use all the Arduino open source platform to create or learn interactive objects. Compared with UNO R3, this is with main Chip ATmega2560, with more I/O Pins, and additional 10 PWM output, of course, the EEPROM is also with larger space. A4988 StepStick Compatible Stepper Motor Driver Module: A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and +- 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power sequencing. A4988 surface mount QFN package (ES), a size of 5 mm x 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin leadframe plating. Note: PCB Colors May vary LCD 2004 Graphic Smart Display Controller: This full graphic Smart Controller contains a SD-Card reader, an rotary encoder and a 128 x 64 dot matrix LCD display. You can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card. Package includes: 1 x 3D Printer Controller RAMPS 1.4 Board 1 x Arduino-Compatible Mega 2560 R3 5 x A4988 StepStick Stepper Motor Driver Module 1 x LCD 2004 Craphic Smart Display Controller 1 x USB Cable

Description: A4988 is a complete microstepping motor driver with built-in translator for easy operation. This product is available in full, half, 1/4, 1/8 and 1/16 step modes operate bipolar stepper motors, output drive capacity of up to 35 V and ± 2 A. A4988 includes a fixed off-time current regulator, the regulator in slow or mixed decay modes. A4988 converter is the key to the easy implementation. As long as the "step" input inputting one pulse drives the motor one microstep. There are no phase sequence tables, high frequency control lines, or complex interfaces to program. A4988 interface is very suitable for complex microprocessor is unavailable or is overburdened. In the micro-step operation, A4988 chopping control inside automatically selects the current decay mode (Slow or Mixed). In mixed decay mode, the device is initially set to a fixed downtime in some fast decay, then the rest of the slow decay downtime. Mixed decay current control scheme results in reduced audible motor noise, increased step accuracy, and reduced power consumption. Internal synchronous rectification control circuitry is provided to improve the pulse-width modulation (PWM) operation power consumption. Internal circuit protection includes: thermal shutdown with hysteresis, undervoltage lockout (UVLO), and crossover-current protection. Special power sequencing. A4988 surface mount QFN package (ES), a size of 5 mm × 5 mm, nominal overall package height of 0.90 mm, with an exposed pad for enhanced thermal dissipation. This package is Pb (suffix-T), with 100% matte tin leadframe plating. Feature: Simple step and direction control interface Short-to-ground and shorted-load protection Five different step resolutions: full-step, half-step, quarter-step, eighth-step, and sixteenth-step Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates Package included: 10 x Step motor driver module