Tester s wille car

Circuit tester 12905 For car electricians 6-12 and 24 volt Pointing probe, cover cap, connecting lead with alligator clip Code Length STW77380001 120mm

Car Fuse Current / Resistance Tester / Voltage Tester Circuit Tester Description: This test can be used to quickly and accurately safely out of the fuse box in the car to measure current,  Can be used for passenger cars and commercial vehicles fault circuit on the search. It comes with an LCD screen,  Easy to use, it can be directly plugged into the car's fuse panel.   Technical parameters: Current Test Measuring range : 0.1A-19.9A Maximum load : 20A/48V DC, the maximum duration of 10 seconds Accuracy :  2% Fuse Type : Medium Blade Fuse Operating temperature : 0  -40 Storage temperature : -10  -50 Voltage Test Measuring range :1-48V Accuracy :  2% Note : When the test voltage is less than 1V, LCD display will show Err   Instructions: 1,The vehicle 's ignition off, remove the fuse circuit under test , the tester will fuse it into the socket ,  This will ensure the protection circuit in the correct level. 2,The test piece is inserted into the car 's fuse socket. 3,If necessary , start the ignition of the car, so that the test circuit is live , open tester power switch. 4,So that the test circuit is in working condition, the measured current value of the test 's screen will display   Safety instructions: 1,During the test , flaky fuse may become hot , remove it before , you should wait for it to cool 2,When used, must not exceed the maximum test load : 20V/48V, the maximum duration of 10 seconds 3,Before connecting and removing the test , make sure the car 's ignition is turned off. 4,Do not disassemble and modify the tester tester line 5,Maintaining a dry tester 6,Remove the tester , do not pull the cable tester 7,When the tester is damaged or not working properly, do not use 8,When the test is not in use, should be stored in a dry location safe and reach of children   Package Included: 1 X Car fuse current / voltage tester

Car Fuse Current / Resistance Tester / Voltage Tester Circuit Tester Description: This test can be used to quickly and accurately safely out of the fuse box in the car to measure current, Can be used for passenger cars and commercial vehicles fault circuit on the search. It comes with an LCD screen, Easy to use, it can be directly plugged into the car's fuse panel. Technical parameters: Current Test Measuring range: 0.1A-19.9A Maximum load: 20A/48V DC, the maximum duration of 10 seconds Accuracy: ± 2% Fuse Type: Medium Blade Fuse Operating temperature: 0 -40 Storage temperature: -10 -50 Voltage Test Measuring range:1-48V Accuracy: ± 2% Note: When the test voltage is less than 1V, LCD display will show Err Instructions: 1,The vehicle 's ignition off, remove the fuse circuit under test, the tester will fuse it into the socket, This will ensure the protection circuit in the correct level. 2,The test piece is inserted into the car 's fuse socket. 3,If necessary, start the ignition of the car, so that the test circuit is live, open tester power switch. 4,So that the test circuit is in working condition, the measured current value of the test 's screen will display Safety instructions: 1,During the test, flaky fuse may become hot, remove it before, you should wait for it to cool 2,When used, must not exceed the maximum test load: 20V/48V, the maximum duration of 10 seconds 3,Before connecting and removing the test, make sure the car 's ignition is turned off. 4,Do not disassemble and modify the tester tester line 5,Maintaining a dry tester 6,Remove the tester, do not pull the cable tester 7,When the tester is damaged or not working properly, do not use 8,When the test is not in use, should be stored in a dry location safe and reach of children Package Included: 1 X Car fuse current / voltage tester

This nifty little gadget is used to check the quality of your car's brake fluid to ensure safe driving. It will test the water content in the brake fluid and will warn you when the brake fluid is not safe to use anymore. Features: The LED indicators will show the percentage of water in the brake fluid with 3 colours green yellow and red Calibrated for cars using DOT4 and DOT3 brake fluids. Easy and quick to use. CE and RoHS approved. Protective cap included. Takes 1 x AAA/1.5V battery (not included) Contents: Brake Fluid Tester Pen User manual

Description: Paint thickness gauge Measure the thickness of non-magnetic coatings Measurement mode Fe Automatic calibration Data hold function Auto power off Compact design Free blue pouch inclued Specification: Measuring Range 0.0mm to 2.0mm Accuracy 2%rdg ±0.1mm, or 2%rdg ±4mil Resolution 0.1mm/1mil Power Supply 1 x 3V button cell, CR2032 or equivalent Operating Temperature 0°C to 40°C Relative Humidity Temperature Coefficient 0.05x(2%rdg ±0.1mm Size(LxWxH) 7x4x2cm Weight 30g Instruction: 1. Hold the tester and make sure that it is as least 20cm away from the object to be tested and other objects. Then press the "TEST"button to turn on the tester."--"appear on the display and flashed,meanwhile the unit "mm"appear. 2. Press the "UNIT"button to select desired unit - mm or mil. 3. Place the tester's probe perpendicularly on the surface to be tested,the display will show the coating thickness. Note: Accuracy is guaranteed at the operating temperature of 23°C ± °C and relative humidity of not more than 75%. Packge Included: 1 X Paint Thickness Meter

Description: AE100 is a quick go tester for relays that provides you with an indication of the general health and functioning of the most common Automotive relays. Tester will check for proper functioning of the relay contacts by connecting the car battery (11V--15V) to the relay coil. Tester will watch the pin configuration, the time to contacts closure and opening, consistency of the relay during each test session. Tester will light the GREEN LED if all passed during the test session, if not light the RED LED. Operating Instructions: 1. Connect the power leads to the car battery -- black alligator clip to negative terminal, red alligator clip to positive terminal. 2. Tester is powered up when the LED illuminates in RED. Check the relay before plugging into the tester. If it’s a 4 pin relay, select “4 pin” on the tester. If it’s a 5 pin relay, select “5 pin” on the tester. 3. Plug in the relay into one of the three receptacles. Press the “Test” button. 4. Tester will check the pin configuration of the unknown relay. Tester will light the RED LED if the unknown relay is not the same to the most of common automotive relays or the pin of the unknown relay is destroyed. 5. Tester will open and close the relay 10 times for testing the time to contacts closure and opening if the pin configuration of the relay is right. Tester will light the RED LED immediately if the time is overtime. 6. Tester will check the consistency of the relay after testing the time to contacts closure and opening ten times. Tester will light the GREEN LED if the test passed, if not light the RED LED. 7. Disconnect power leads from the car battery and remove relay from the tester. Package Included: 1 X Automotive Relay Tester(JH100) 1 X User Manual 1 X Carry Bag

Description: The tester can be used as a digital brake fluid tester suitable for determining brake fluid quality. Developed for professional use in automotive repair shops and in servicing. Quality is tested and indicated on five LEDs in terms of "percent of water in the brake fluid". Ready for Brake Fluid Test Unscrew the brake fluid reservoir,and pull off the cap of the Brake fluid tester. Dip the test probes into the brake fluid up to the plastic rim of the device. To Check Fluid Quality Press the button for power on,green LED will light up. Insert teh tester into reservoir for one second then the test result will be correctly indicated by LEDs. Repress the button for power off.The tester will automatically power off after about 15 seconds of inactivity. Product Labelling Indication Green: Battery OK,i.e.: No water contained in the brake fluid. Yellow: Less than 1% of water content in the brake fluid. Yellow/yellow: Approx.2% of water content in brake fluid. Yellow/yellow/red: Approx.3% of water content in brake fluid. The brake fluid should be changed. Yellow/yellow/red/red: At least 4% of water content in brake fluid. The brake fluid should be changed urgently! Extreme danger! 1x AAA Battery (Not Included) Specification Color Black Quantity 1Pc LED 5 Package includes: 1x LED Car Brake Fluid Tester Delivery: Delivery to countries utilizing ePacket such as the USA, Australia, Austria, Belgium, Canada, Denmark, Finland, France, Germany, Greece, Hong Kong, Hungary, Ireland, Israel, Italy, Japan, Korea, Luxembourg, Malaysia, Mexico, Netherlands, New Zealand, Norway, Poland, Portugal, Russia, Saudi Arabia, Singapore, Spain, Sweden, Switzerland, Thailand (currently in a trial run), Turkey, Ukraine And the United Kingdom delivery can be within 7-14 days. Other countries will take 50-60 days, although we have experienced some deliveries in 30 days. Please note that there can be additional delays at customs and we can not be held accountable for such actions. Additional taxes and duties may be calculated by customs which will be for the buyer's account. Delivery is GUARANTEED, and should you not receive your order, a FULL REFUND will be made. Tracking: For every order a tracking number will be supplied as soon as the package has been shipped. The package can be tracked on www.17track.com You can also download the mobile app where the package can be tracked and to be updated of any status changes with push notification. Express delivery: We have the option to get your purchase delivered speedily. Please contact us to request a quote on express delivery.

Feature: 1. This tester can diagnose injector problems, you can use it on each injector, 2. Individually to test stuck, leaking or burnt-out. 3. It used 12V vehicle battery as power supply. 4. It has 4 pulse modes and in the continuous working mode (mode 4), it can help, 5. You identify the injector good or not when you switch off the engine. 6. The lock mode can ensure the testing condition is same. 7. It can work with any fuel pressure tester together. Specification: Power Supply: 12V vehicle battery Operation Environment: 0 ￢ﾄﾃ-40￢ﾄﾃ, relative humidity Storage Environment: -10￢ﾄﾃ-50￢ﾄﾃ, relative humidity Size: 147x82x29mm (for main body only) Weight: about 165g Operation instruction: 1. Turn off the vehicle’s engine. 2. Connect Black / Red Clip to the Negative / Positive terminal of battery. 3. Connect pulse output terminal to the fuel injector. 4. Press the "MODE SET" key to select the desired pulse mode. 5. Press the "PULSE" key, the tester will output pulse to the injector, and then the pulse signal indicator will light as indication. EM276 Explanations for 4 modes: Mode 1: the tester outputs 1 pulse, whose pulse width is about 250ms Mode 2: the tester outputs 50 pulse, every pulses pulse width is about 7ms Mode 3: the tester outputs 100 pulse, every pulses pulse width is about 3.5ms Mode 4: the tester outputs pulse continuously at the ate of 0 pulses per about 1450ms, very uses pulse with is about 7ms Package Included: 1 X Automotive Fule Injector Tester 1 X Carrying Pouch 1 X English User Manual

Description: This tester connect 13-pins plug of trailer between 13-pins socket of a car. It helps to diagnostic follow problem: 1. Some LED do not light up. 2. None of the LED light up. 3. One or more LED are weak or twinkle. 4. All the LED are weak or twinkle. 5. The lights of the trailer do not light up but the LED do. Specification: Brand Name Tirol Number T23331 Name Trailer Tester Material ABS+ copper Type 13 Pin Applicable Diagnostic Tools Color Black Weight 220g Size 20.5x4.5x5.5cm Instrument: 1. Put the tester in the socket of the car. 2. Press the yellow button on the side of the tester. 3. If the wiring is good, all the LED light up. Do again steps 4 as previous. Tip: You can also test the functions of each pin of the socket. 1. Switch on the left hand indicator (after switching on the ignition key). 2. The corresponding LED must flash with the same frequency. If not, left hand indicator wiring is defective/broken. 3. Repeat steps 1 and 2 for the right hand indicator, rear-light, fog-light and stoplights. 4. With a +/- 4 m extension cable, you can test the functions form the driver¿s seat more easily. Package Included: 1 X Trailer Tester

Feature: 1. Can test all cars to start lead-acid batteries, including ordinary lead-acid batteries AGM flat, Battery AGM winding battery colloid batteries and so on. 2. Can be detected directly out of the battery. 3. With polarity reverse polarity protection, clip reverse will not damage the tester, and no heat, no spark will not damage the battery or hurt the body of the operator. 4. Can directly test the loss of battery, no need to be fully charged in the test. 5. Test standards include the world's vast majority of commonly used battery standards, such as CCA / BCI / CA / MCA / JIS / DIN / IEC / EN / SAE / GB, etc. Specification: Shell Material: Acid Acrylonitrile Butadiene Styrene (ABS) Color: Red Size: 12x7cm Voltage range: 12V Range CCA: 100-800 Battery range: 30AH-100AH Operating temperature: -20 ¿¿¿ -50 ¿¿¿ Applicable battery: 12V starting type lead acid battery Special test clip: double conductor Kelvin folder How to use: 1. The tester black and white clip clip to the measured battery, red and black negative, the tester will display the boot interface. The measured voltage is below 6.0V The following can not be normal test; press OK key to continue down 2. Follow the tester prompts, and then select: (1) Input standard selection: refers to the factory standard factory standard, in the battery directly above or can be seen, Select the standard marked on the battery can be, such as CCA, BCI, DIN and so on (2) Rated capacity selection: refers to the battery factory starting current standard, in the battery directly above or before you can see, then press OK button to start testing. Package Included: 1 X Auto Battery Tester

FOXSUR 12V Battery Analyzer Digital Tester Professional Diagnostic Tool Package weight: 0.15 kg Description: 1. Usage Scope: All car lead-acid starter battery, including regular flooded, EFB, AGM tablet battery, AGM winding battery, GEL battery,WET, SLA etc. 2. Much wider test range and more accurate. Test results based on SAE,DIN, IEC, EN, CA, JIS, Standards. Test range: CCA20-1200, 30AH - 200Ah,Test result: SOH, SOC, CCA Value, IR, Starting & Charging system, etc. 3. Small compact design, scan faster and indicates test results directly. Even a beginner can use this unit to analyze any 12V batteries healthy, tells you everything about the battery: voltage, charge,cranking power, and how much life is left in the battery (level of Ohm resistance). Does it quickly and precisely. 4. Provides check the Alternator's charging and Starter's cranking conditions. Vehicle charging system test is also available, including load voltage, unloaded voltage, ripple status and charging system status. 5. The FBT1201 battery tester indicates test results directly. no internal batteries required and gets the power directly from the 12V battery. Specification: Test range: CCA20-1200, 30AH - 200Ah Test result: SOH, SOC, CCA Value, IR, Starting & Charging system, etc. Test standards: SAE,DIN, IEC, EN, CA, JIS Voltage measure range: 7V-15V DC Housing material: ABS plastic Suitable for: Automobile facory, garage, auto battery manufacturer, auto battery agent, educational institution, DIY enthusiasts, etc. Package Included: 1 X Battery Analyzer Click here for more deals FOXSUR 12V Battery Analyzer Digital Tester Professional Diagnostic Tool FOXSUR 12V Battery Analyzer Digital Tester Professional Diagnostic Tool

Description: 1. Usage Scope: All car lead-acid starter battery, including regular flooded, EFB, AGM tablet battery, AGM winding battery, GEL battery,WET, SLA etc. 2. Much wider test range and more accurate. Test results based on SAE,DIN, IEC, EN, CA, JIS, Standards. Test range: CCA20-1200, 30AH - 200Ah,Test result: SOH, SOC, CCA Value, IR, Starting & Charging system, etc. 3. Small compact design, scan faster and indicates test results directly. Even a beginner can use this unit to analyze any 12V batteries healthy, tells you everything about the battery: voltage, charge,cranking power, and how much life is left in the battery (level of Ohm resistance). Does it quickly and precisely. 4. Provides check the Alternator's charging and Starter's cranking conditions. Vehicle charging system test is also available, including load voltage, unloaded voltage, ripple status and charging system status. 5. The FBT1201 battery tester indicates test results directly. no internal batteries required and gets the power directly from the 12V battery. Specification: Test range: CCA20-1200, 30AH - 200Ah Test result: SOH, SOC, CCA Value, IR, Starting & Charging system, etc. Test standards: SAE,DIN, IEC, EN, CA, JIS Voltage measure range: 7V-15V DC Housing material: ABS plastic Suitable for: Automobile facory, garage, auto battery manufacturer, auto battery agent, educational institution, DIY enthusiasts, etc. Package Included: 1 X Battery Analyzer

Specification: Name: Cylinder Leak Tester Group Main Material: Metal, plastic Measuring range: 0-100psi Fixed short connector: M12 Fixed long connector: M14 Hose total length: 36cm Case: 34 x 25 x 8cm Fit For: 1. Test car engine cylinder sealability whether is within the scope of allow leakage,can also further from the failure phenomena to analysis and determine the location and causes of leakage in order to take measures to troubleshoot. 2. Designed to detect a variety of common engine faults including: Worn piston rings, worn valves,cracks in cylinder walls and blown head gaskets.Available with either single gauge or twin gauge manifold. Gauge(s)show % of cylinder leakage or cylinder leakage and cylinder pressure.Suitable for use on any petrol engine with 14. 12 or 10mm spark plugs.Supplied in carry-case with instructions. (Suitable for use on any petrol engine with 12mm or 14mm spark plugs) Package Included: 1 X Dual Gauged Leak Detection Unit 1 X Flexi Hose 1 X Fixed Short Connector 1 X Fixed Long Connector 1 X Case

EM415 Pro Automotive Cable Wire Short Open Digital Finder Car Repair Tool Tester Tracer Diagnose Description: Tracing of wires is made possible even inside bundles, conduits, behind  panels, under carpets, upholstery, etc Easy to use: simply connect the transmitter in series with the circuit or wire  under test, (i.e.: in place of a blown fuse, across a connector,in series with  an open wire, a light bulb socket, etc.), and scanning the circuit/wire with the  tracers flexible probe to find the trouble spot 42 V Ready: for use in the new generation of vehicles with mixed or single 42  Volt systems Operates on DC voltages from 6 to 42 volts Internally protected against power surges and overloads 7" flexible probe allows reaching wires in congested places Transmitter and Receiver LEDs show open or short circuit conditions Adjustable sensitivity for all tracing situations No wire piercing required, non-contact technology!   HOW TO USE THE PROBE? The probe of the Receiver is built of coiled steel and may be bent as needed,  in order to reach wires in ongested or difficult areas. Depending on the circuit  characteristic and sensitivity settings, the probe will pick up the signal from  the wire in a range of positions. However,for the best possible range the  Receiver’s probe tip (black cap) should be positioned perpendicular  (at 90o) to  the wire being traced and either above or below it. Package Included: 1 X Automotive Short and Open Finder 1 X Instruction Manual APPLICATION: Checking for short circuit,Loating open circuit,Wire identification, Wire traceing,etc.

EM415 Pro Automotive Cable Wire Short Open Digital Finder Car Repair Tool Teste Package weight: 0.28 kg EM415 Pro Automotive Cable Wire Short Open Digital Finder Car Repair Tool Tester Tracer Diagnose Description: Tracing of wires is made possible even inside bundles, conduits, behind panels, under carpets, upholstery, etc Easy to use: simply connect the transmitter in series with the circuit or wire under test, (i.e.: in place of a blown fuse, across a connector,in series with an open wire, a light bulb socket, etc.), and scanning the circuit/wire with the tracers flexible probe to find the trouble spot 42 V Ready: for use in the new generation of vehicles with mixed or single 42 Volt systems Operates on DC voltages from 6 to 42 volts Internally protected against power surges and overloads 7" flexible probe allows reaching wires in congested places Transmitter and Receiver LEDs show open or short circuit conditions Adjustable sensitivity for all tracing situations No wire piercing required, non-contact technology! HOW TO USE THE PROBE? The probe of the Receiver is built of coiled steel and may be bent as needed, in order to reach wires in ongested or difficult areas. Depending on the circuit characteristic and sensitivity settings, the probe will pick up the signal from the wire in a range of positions. However,for the best possible range the Receiver’s probe tip (black cap) should be positioned perpendicular (at 90o) to the wire being traced and either above or below it. Package Included: 1 X Automotive Short and Open Finder 1 X Instruction Manual APPLICATION: Checking for short circuit,Loating open circuit,Wire identification, Wire traceing,etc. Click here for more deals EM415 Pro Automotive Cable Wire Short Open Digital Finder Car Repair Tool Teste EM415 Pro Automotive Cable Wire Short Open Digital Finder Car Repair Tool Teste