Shield micro

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA More informations: https://myosuploads3./products/20181029/20181029050819SKU122168.rar Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 1 x Micro SD TF card module Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter For Arduino

5Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 5 x Micro SD TF card module

Buy Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R210.00

Buy Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R182.61

Buy MICRO:BIT SK6812 4X8 LED DOT MATRIX DISPLAY SHIELD KS0315 for R199.96

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Package contains 1 X item of the smallest listed variant.

Buy 3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter for R182.61

Buy 30pcs Micro TF Card Memory Shield Module SPI Micro Storage Card Adapter for R427.00

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Buy TERMINAL BLOCK SHIELD FOR BBC MICRO:BIT KS0433 for R179.30

Buy ESP32 ESP32S 18650 Battery Charge Shield V3 Micro USB Type-A USB 0.5A Test Char for R125.85

Description: Data logging shield for Arduino NANO a new for Arduino NANO shield,You can get going quickly - saving data to files on any FAT16 or FAT32 formatted SD card, to be read by any plotting, spreadsheet or analysis program. The included Real Time Clock timestamps all your data with the current time, so that you know precisely what happened when! Please note that this item does not come with an for Arduino NANO (you'll need one to use with the shield), or an SD card. SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card Real time clock (RTC) keeps the time going even when the for Arduino is unplugged. The battery backup lasts for years Included libraries and example code for both SD and RTC mean you can get going quickly Prototyping area for soldering connectors, circuitry or sensors. Onboard 3.3v regulator is both a reliable reference voltage and also reliably runs SD cards that require a lot of power to run Works with for Arduino NANO or MICRO Package Included: 1 x Nano Data Logging Shield For Arduino(Battery not included)

Description 18650 Shield - Power Module This 18650 battery shield is used to charge and power an Arduino, ESP8266, ESP32 expansion board via the USB output (type A) or directly using the 6 outputs (soldering pin) available on each side of the board (5V or 3V). The shield has a charging circuit (not protected against polarity inversions). An LED indicates the progress of the battery charge (Green = charged, red = charging). Quick Spec Power supply: 5 to 8V via micro USB port up to 0.5A Output power 5V via USB Type A port 3 connectors to deliver 3V up to 1A 3 connectors to deliver 5V up to 2A Misc: 1 USB output, LED for the state of charge (green = battery charged, red = charging) Battery protection (overcharging or over-discharging). Attention, no protection in case of reverse polarity Dimensions: 98 x 29 mm Shipping List 1 X 18650 Shield - Power Module More Products View More Products

Buy 3pcs ESP32S ESP32 0.5A Micro USB Charger Board 18650 Battery Charging Shield Wemos for R265.00

GPS Shield GPS Record Module With SD Interface For Arduino Introduce: The expansion board is specifically designed for the Arduino UNO and other GPS record expansion board. Provides two kinds of GPS antenna interface. Supports 3.3V and 5V two voltage levels of operating base (such as leaf maple), IO port interface leads with multiple analog pins can be directly connected to the electronic building blocks for rapid prototyping. With SD card slot, support for GPS information record. Can be used with FT232RL module, directly connected the FT232RL module's TX, RX, VCC, GND to GPS corresponding feet, through the serial debugging software to view the data. Feature: Provides 3.3V and 5V operation level select, so it can be compatible with more baseboard, such as 3.3V ChipKit UNO32, leaf maple and other platforms, compatibility stronger. Use active GPS antenna. With micro SD interface. Can be set via jumpers connected to TxD and RxD you need Ardino pins (D0-D8 optional), it is more stronger expansibility than directly connect D0D1. Provides multiple electronic building blocks interface to facilitate quick access various types of electronic building block modules, the Add button, LED display or a relay switch function. TF deck, SPI interface. Support Arduino library. With reset button, you can direct reset Arduino backplane. What INT1 INT0 is? If you use a jumper connected to ON, then the two trigger signals from the GPS module (such as every second clock signal, each output prompt signal information) pin is connected to the Arduino interrupt pins, you can use these trigger an interrupt to do the setting you need- Default is off. Description: Board size: 56 x 54mm Weight: About 45g Operation temperature: -40°C to +85°C Package included: 1 x GPS shield with antenna

Description: This is the old version of WeMos D1. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0) 1 analog input(3.3V max input) A Micro USB connection A power jack, 9-24V power input. Compatible with Arduino Compatible with nodemcu Infos: click here!! Package included: 1 x WeMos D1 WiFi UNO ESP-12E Based ESP8266 Shield For Arduino Compatible

Description: This is the old version of WeMos D1. 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0) 1 analog input(3.3V max input) A Micro USB connection A power jack, 9-24V power input. Compatible with Arduino Compatible with nodemcu Infos: click here!! Package included: 3 x WeMos D1 WiFi UNO ESP-12E Based ESP8266 Shield For Arduino Compatible

Feature: 2.8 inch LCD TFT display Bright, 4 white-LED backlight Colorful, 18-bit 262,000 different shades 4-wire resistive touchscreen 240 x 320 pixels with individual pixel control No wiring, no soldering. Simply plug it in and load library On-board 3.3V 300mA LDO regulator 5V compatible, use with 3.3V or 5V logic Support 2GB micro SD TF card Size: 7.8 x 5.3cm Package included: 1 x 2.8 Inch TFT LCD Shield Touch Display Module

Description: 1. Compatible with Arduino IDE 1.5 (OSX/Win/Linux) 2. Fully signed drivers and executable for easy installation 3. USB programming, USB device emulation, USB-CDC virtual serial port emulation 4. 16 MHz AVR MCU - using a true 16Mhz precision crystal 5. 16KB Flash Memory (14.5K+ after bootloader) 6. Serial over USB debugging and communication! 7. 14 I/O Pins (2 shared with USB) 8. I2C, true SPI, UART, LIN, and USI 9. ADC on 10 pins 10. 3 PWM Channels (which can be assigned to a selection of pins) 11. Power via USB, or External Source - 5v or 6-16v (automatic selection) 12. On-board button that can be used as a reset, program, or user button - or can be disabled to use that pin as general i/o - without changing the bootloader 13. On-board 150mA 5V regulator 14. Power LED and Test/Status LED (on Pin 1) 15. User accessible solder jumpers to disable LEDs, and other features for lower power consumption 16. Two mounting holes. 17. Breadboard compatible pin out/spacing (the three side header pins are only for legacy shield support). Package included: 1 x Wemos® Digispark Pro Kickstarter Development Board

  A brilliant Superman Logo Light to brighten up your home. Shaped like the iconic Superman 'S' shield, this is a perfect gift for any comic book or superhero fan. The Superman 'S' shield is more than just a logo, it's a symbol of everything the Man of Steel represents. At 190mm tall (approx 7.5 inches), the Superman Logo Light is a shining monument to the greatest superhero of them all, and makes for a truly impressive and highly distinctive light for your room. The Superman Logo Light comes with a detachable stand, so can either be left free standing or, by removing the stand and using the wall mounting options on the back of the light, hung up on a solid wall for an even more impressive effect. Superman is the most popular and universally recognized comic book character of all time. First appearing in Action Comics in 1938, the character immediately became an icon of popular culture. Superman has featured in countless films, TV series, graphic novels and video games, including the 2016 blockbuster movie Batman v Superman: Dawn of Justice. The Superman Logo Light is dual powered. A 1.5m length (approx 60in), micro USB cable is included, or alternatively the light can be powered by 3 x AA batteries. Batteries are not included. The Superman Logo Light is an officially licensed Superman product. Recommended for ages 8 and above.A brilliant Superman Logo Light to brighten up your home. Shaped like the iconic Superman 'S' shield, this is a perfect gift for any comic book or superhero fan 4 colour box packaging

HD Helmet Sport Car Action Digital Video Waterproof Camera Camcorder DV 1280*720 SJ1000  Description: 720P HD mini action camcorder LCD preview screen and resistive shock for convenient operation Adopts CMOS image sensor Suitable for mount on bike, surf board and etc Captures video & photo and records 720P HD videos Removable Micro SD/ TF card for easy transfer and viewing on any computer Powered by built-in rechargeable battery Specification: Function mode Videoing, Taking photos, Vehicle-mounted mode, Removable disk, PC cam Image sensor 1.3 million pixel(CMOS) Image file format JPEG Video file format AVI Image resolution 5M(2592x1944), 3M(2048x1536), 1M(1280x1024) Video resolution VGA: 640x480(60 frames/second), 720P: 1280x720(30frames/second) Power source Lithium 320mAh Power supply Built-in 3.7V rechargeable lithium Operating system Microsoft Windows2000, XP, Vista 7 Power life More than 1 hours Shutter control Electronic EV compensation AUTO Sensitivity AUTO White balance AUTO Exposure AUTO Scenes AUTO Supported O/S Microsoft window 2000, XP, vista Window 7 Storage medium Micro SD card (UP to 32GB), (without bulit-in flash memory) USB interface High-speed USB 2.0 interface Camera lens F3.1 f=9.3mm Digital zooming 4 times LCD display screen 2.0-inch touch screen CPU Intel Pentium III of more than 800MHz or other CPU with equivalent performance Internal memory Larger than 512MB Sound card and display card The sound card and display card shall support DirectX8 or higher version DirectX8 or higher version CD driver Speed of 4 times or faster Hard disk Excelent space of more than 500MB Others One standard USB1.1 or USB2.0 port Size 67 x 45 x 29mm / 2.64" x 1.77" x 1.14" Package Included: 1 X Mini Camcorder 1 X Waterproof Case    1 X USB Data Cable 1 X Shield 1 X Car Charger      1 X Suction Cup Mount     1 X Handlebar Seatpost Mount    1 X Helmet Mount 1 X Helmet Belt 1 X User Manual    

GoXtreme Rallye 720p HD Action Camera Silver What's in the box? Rallye Silver Action Camera Waterproof Case Shield Bike Mount Helmet Mount Holding Arms Battery USB Cable Specifications: - 2.0"/5cm TFT display - Up to 30m waterproof case - 1.3 Mega Pixels CMOS Sensor - Still Image Resolution: 5MP (2592?1944), 3MP (2048?1536), - 2MP (1600?1200), 1MP (1280?960) - Image File Format: JPG - Video Resolution: 720P (1280x720P) Pixels 30fps, 480P (640x480P) Pixels 30fps - Video File Format: AVI Motion JPG - Video with sound - Microphone built-in - Micro SD card support up to 32GB, minimum Class 10 (not included) - Time Lapse: Off/2s/10s - 120 degrees wide angle - Continuous shot - PC Interface: Micro USB - 900mAh lithium battery (exchangable) - Dimensions: 60 x 24.5 x 41 mm, 58g (including battery) - System requirements for mass storage function: - Microsoft Windows XP, Vista, Win7, Win8, Mac 10.2 or above - After reaching a max. video recording time of 29 minutes the camera will automatically stop. - It can only be restarted manually. Need to show the world what you're made of? With it's compact size and rugged, waterproof housing to protect against humidity, water and dirt, the GoXtreme Rallye is fearless in all conditions. Whether you're on the water, under water, mountain biking, or snowboarding, Rallye's 720p recording means you can relive all of your best moments in stunning high definition. As your perfect outdoor companion, the GoXtreme Rallye HD action camera has just what you need to capture that perfect moment. Simply mount the camera with the included handlebar or helmet mounts and check out the action on the built-in 2.0" display. Going deep..? No problem, the waterproof case included will keep your Rallye safe and dry down to 45M depth. WE OFFER FREE DELIVERY!!

Descriptions: - The coordinated movement of 3 mini servos is used to move the environment, and the environment can be perceived by infrared ranging, and the brightness of the surrounding light can also be perceived. - The center of the product is a powerful Beetle controller and expansion board, and it is programmed with simple and easy to use Arduino. - It can advance, retreat, avoid obstacles, turn corners, patrol light and so on. - These functions make worms walk more complex and interact more richly. - The simple assembly allows you to understand the most basic principles of robotics and intelligent control. - Users who like DIY can also transform their interactive mode on the basis of the original code.   Specifications: - Operating voltage: 5-6.4V (4 on the   AAA battery) - Controller: Bluno Beetle (Bootloader: Arduino UNO) - Bluetooth wireless programming and wireless access are added. - After assembly size: about 180x153X120mm - Weight: about 240g Documents:  1. Assembly Manual (Bluno Beetle Version) V2:  please click to reference. 2. Sample Code (Bluno Beetle Version):  please click   to reference. Note: *  The following necessary tools may be required to complete the assembly of the product:    Screwdriver, needle nose pliers, scissors (not included in the product package) *  Please allow 1-3CM differs due to manual measurement. Package Included: 1 x Insect robot Hexa Robot DIY Kit  [1 x  Master module (Bluno Beetle microcontroller + Bluno Beetle shield)  3 x 9g Micro Servo  1 x GP2Y0A21 distance sensor  1 x Sensor Bracket 2 x Two on AAA Battery Box 1 x Heat shrink tube-Black (diameter 6mm-100mm long) 3 x Steel wire  200mm x 1mm 1 x Servo connector 1 x White foam double sided glue (L / W / H: 78x61x3mm) 2 x Digital sensor line 3 x Cable tie (1.8x100mm)  1 x High quality micro USB data Line]

Chord Company Signature Tuned ARAY USB Cable There are a lot of musicians working at the Chord Company and a good few play in bands. Someone had done some recording and copied the master CD to a laptop so he could burn a few copies. Out of curiosity we compared the master to a copy. The copy was beyond dreadful. Since we were using one of the first DACs with a USB input, we listened to the copy on the laptop next.  Not good, but better than the CD version. So we started to investigate higher spec ripping programs and playback management big improvements. So now we could make a pretty decent CD copy of the master but there was still the copy on the laptop. We knew it was OK, as wed burnt the CD copies from it, but straight out of the laptop and into the same DAC via USB it wasnt as good. Like any self-respecting cable company, we listened with a selection of available USB cables and found that USB cables were worth exploring. The result was the Chord USB SilverPlus   with silver-plated conductors and high frequency effective shielding. The Signature USB features four separately shielded conductors. The signal conductors are silver plated, insulated with PTFE and fitted with dual layer high frequency effective shielding and a Tuned ARAY conductor geometry developed for USB cables.  The 5 volt cables are pure copper with a gas foamed Polyethylene insulation and a high density braided shield. All connections are soldered and the USB plugs are silver-plated to our specification in the UK. There are quite a lot of storage and streaming devices available and the Signature Tuned ARAY USB is an obvious choice to try with these. Dont pass the chance by to try the Signature Tuned ARAY USB with a computer/laptop though. If its full of decent rips of your own CD collection, high quality downloads or is being used for streaming something like Tidal and you have a decent DAC, try the Signature Tuned ARAY USB. One of the sources we use in our demo room is a Dell laptop with solid state storage full of DB Power amp CD rips and some downloaded high resolution tracks.  Put it on the rack, connect it with the Signature Tuned ARAY USB and it becomes a serious source component. The Signature Tuned ARAY USB is available in standard 1m lengths. Custom lengths are available to order. NB. Micro USB connections are just too small to fit any of the cables we use to. The problem is that are some outstanding DACs with micro-USB connectors. Curiosity drove us to experiment with adaptors so we could hear what happened when we used different USB cables with a DAC that only had a micro USB connection. We were glad we did so much as we dont like adaptors we end up using them with all our USB cables if needed. Compromise it is, but a very worthwhile one.

R) You can mount this semi-transparent waterproof shockproof camera on your car's dashboard, your skateboard, bicycle, head-gear when diving, underwater (10m easily)etc! R FILM THE COPS OR BADDIES WHEN THEY STOP YOU! colours available = black, blue, red, silver, white Features: 720P HD mini action camcorder 10m Waterproof 2.0 inch TFT LCD preview screen and touch screen Captures video & photo and records 720P HD videos Removable Micro SD/ TF card for easy transfer and viewing on any PC Specs: Image Senor: CMOS Screen: 2.0 inch TFT LCD screen Zoom: 4X digital zoom Video Resolution: --VGA (640 x P( x 720) Photo Resolution: --1M --3M --5M Image Format: JPEG Video Format: AVI PC: Support Windows XP, , vista and 7 TF Card Slot: Support up to 32GB (TF card NOT included) Power Supply: Rechargeable lithium battery Interface: USB port, TF card slot Package Included: 1 x Mini Camcorder 1 x Waterproof Case 1 x Handlebar Seatpost Mount 1 x Shield 1 x Helmet Mount 1 x Car Charger 1 x Helmet Belt 1 x Suction Cup Mount 1 x USB Cable 1x User's manual

720P HD mini action camcorder. 2.0 inch TFT LCD preview screen and resistive touch screen for convenient operation. Adopts CMOS image sensor. Suitable for mount on bike, surf board and etc. Captures video & photo and records 720P HD videos. Removable Micro SD/ TF card for easy transfer and viewing on any computer. Powered by built-in rechargeable battery. Features 1. Image Senor: CMOS. 2. Screen: 2.0 inch TFT LCD screen. 3. Zoom: 4X digital zoom. 4. Video Resolution: VGA (640 x P( x . Photo Resolution: 1M/3M/5M. 6. Image Format: JPEG. 7. Video Format: AVI. 8. Operate System: Support Windows XP, , vista and 7. 9. TF Card Slot: Yes, Support up to 32GB (TF card NOT included). 10. Power Supply: Rechargeable lithium battery. 11. Interface: USB port, TF card slot. 12. Color may vary 13. Package Included: 1 * Mini Camcorder, 1 * Waterproof Case, 1 * Handlebar Seat post Mount, 1 * Shield, 1 * Helmet Mount, 1 * Car Charger, 1 * Helmet Belt, 1 * Suction Cup Mount, 1* USB Cable."