Pwm servo motor

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot

Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot

Features:   This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs   Package included: 5 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot  

Buy 5Pcs PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module for R653.93

Buy 3Pcs PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module for R396.30

Buy 5Pcs PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module for R634.24

Buy 16 Channel 12-bit PWM Servo motor Driver I2C Module for R109.95

Description: PWM DC Motor Speed Switch Controller 10V 12V 24V Control Reversible Regulator High efficiency, high torque, low heat generating Control the speed of a DC motor with this controller With reverse polarity protection, high current protection Specifications: Material: Plastic, metal Input: 10V-30V Output: Max 120W (When more than 24V) PWM range: 5%-95% Frequency: 500Hz Current: Max 4A (Recommend you to use in 3A) Operating Instruction: 1. Connect it to the power, ensure the positive inversion switch located in the middle of the zero, and connected with a DC power supply (the DC supply voltage range is more than 6V and less than 30V). Warning: do not reverse the positive and negative terminals of DC power source, otherwise regulator may be damaged. 2. Connect it to the motor, the motor line can be positive or negative, when the running direction is not consistent with the expectative one, you can adjust the sequence of lines or switch position to change the direction. 3. Adjust the switch. Positive inversion switch is used to control the motor speed direction. When the switch is located on the zero position, the motor stops rotating. 4.Adjust the potentiometer knob. Adjusting potentiometer knob can change output duty ratio of the regulator, then motor speed change. Package included: 1 x DC Motor Speed Controller Details pictures:

Buy PWM DC Motor Governor 10V-55V 12V 24V 36V 48V 40A Motor Speed Control Module Controller with Display for R295.00

Buy PWM DC Motor Governor 10V-55V 12V 24V 36V 48V 40A Motor Speed Control Module Controller with Display for R344.98

Buy SERVO MOTOR 180-DEG 6V DIGITAL WITH PLASTIC GEARS FS9257D for R233.40

Buy PWM DC Motor Speed Controller 12V/24V/36V 15A Controller Overload Stall Overcurrent Protection... for R219.00

Buy 16 Road PWM/Servo/Steering Gear Motor Drive Plate Controller Robot IIC PCA9685 for R295.34

Mini USB 24 Channel Servo Motor Driver Controller Module For Arduino Robot Specification: 32-bit CPU Power of servo and control board are separate Chip Power Supply: 6.5V ~ 12V or 4.5V ~ 5.5V (one is for USB) Servo Power Supply: Generally DC 5V (base on the servo you use) Channel: 24 (servo speed adjustable) Communication Input: USB or Serial Port(TTL) Signal Output: PWM (accuracy 1us) Servo Motor Resolution: 1us, 0.045 degrees Baud Rate: 9600, 19200, 28400, 57600, 115200, 128000 (recognized automatically) Dimensions: 51.0 x 43.5 x 1.6mm Control Mode: USB and UART (TTL) Flash Memory: 512K ROM Package included: 1 x 24 Channel USB Servo Motor Driver Controller Module

Overview: PCA9685 module could control 16 road by PWM, every road programmable output for shut, open. Through the I2C communication. The function and characteristics: ??Working voltage: 2.3-5.5V ??Communication protocol: I2C ??Cannel number: 16 ??Resolution ratio: 12 bit ??V+ Input: According to peripheral voltage, Maximum 6V Feature: ??The board size: 63.1*31.8mm ??The board function description: VCC: The working voltage of the module GND: Ground SCL, SDA: I2C communication interface V+: Steering gear and other peripheral driving voltage PWM: PWM signal output VCC connect to the Arduino 5V, GND connect to the Arduino GND, SDA connect to A4, SCL connect to A5, steering gear with 0-15 arbitrary channel connection, burn write code, steering gear began to turn it. Package included: 1 x Arduino 16 Road PWM/Servo/Steering Gear Drive Controller