Hilti battery charger c

Hawkins Battery Charger - Pro 224 The Hawkins Pro 224 Battery Charger is a powerful engine starter and battery charger combination. It is intended for table top use at home or in small businesses and garages. The Pro 224 will deliver an engine start aid of 200A c.c. which is sufficient to start petrol and diesel engines up to 2-litre capacity. In charger mode, the charger will charge 12V and 24V batteries. Selection is made by connecting the charging cable to either the 12V stud or 24V stud on the front panel. The transformer is protected by an automatic reset thermal circuit breaker and a 12.5A mains fuse. The output side is protected by a replaceable 80A fuse to guard against incorrect polarity or too high a charging current. Two rocker switches allow for both Battery Charge/Engine Start and HIGH/LOW charging selection. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Battery Charger Switch Position LOW LOW Input Current 0.55A a.c. 1.2A a.c. Ouput Voltage 12V d.c. 24V d.c. Ouput Current 7.2A d.c. 8A d.c. Switch Position HIGH HIGH Input Current 1.48A a.c. 3A a.c. Ouput Voltage 12V d.c. 24V d.c. Output Current 18.5A d.c. 19A d.c. Engine Starter Switch Position LOW LOW Input Current 2.87A a.c. 6.5A a.c. Output Voltage 12V d.c. 24V d.c. Output Current 35.3A d.c. 39A d.c. Switch Position HIGH HIGH Input Current 4.9A a.c. 10.9A a.c. Output Voltage 12V d.c. 24V d.c. Output Current 56A d.c. 62A d.c. Dimensions 320 x 220 x 180mm Weight 10.5kg

Hawkins Battery Charger - Pro 324 The Hawkins Pro 324 Battery Charger is a powerful engine starter and battery charger combination. The Pro 324 will deliver an engine start aid of 300A c.c. and is capable of charging 12V and 24V batteries. Selection is made by connecting the charging cable to either the 12V stud or 24V stud on the top panel. The transformer is protected by an automatic reset thermal circuit breaker and a 12.5A mains fuse. The output side is protected by a replaceable 80A fuse to guard against incorrect polarity or too high a charging current. Two rocker switches allow for both Battery Charge/Engine Start and HIGH/LOW charging selection. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Current Selector 6 6 Battery Charger Switch Position LOW LOW Input Current 3A a.c. 6.9A a.c. Ouput Voltage 12V d.c. 24V d.c. Ouput Current 37A d.c. 44A d.c. Switch Position HIGH HIGH Input Current 4.5A a.c. 9.5A a.c. Ouput Voltage 12.5V d.c. 25V d.c. Output Current 49A d.c. 54A d.c. Min Battery Capacity 35Ah 35Ah Dimensions 260 x 540 x 220mm Dimensions with Handle 260 x 840 x 220mm Weight 17.5kg

iMars Green 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Aci Package weight: 0.46 kg Specification: Name: 12V 6A Intelligent Charger Input voltage: 100-240V AC, 50-60Hz 75W Rated output: 12V DC, up to 5-6A. Charge voltage: Summer mode:14.4V, Normal mode:14.7V, Winter mode:15.5V (Measurements allowed tolerance +/-0.4V) Battery range: 4-100Ah Thermal protection: 65'C +/- 5'C Operate temperature:-20'C~45'C Cooling:Fan Chargeing process:3-stage:CC,CV,Float charge Efficiency: App. 85%. Size (length × width × height): 148 × 85 × 60mm Charging line length 60CM, clip line 55CM Features: Microprocessor control (CPU). LCD display charging voltage, charging current, display charger internal temperature (with a certain error) For problematic batteries, press the Repair button to pulse repair the battery. 3-stage automatic charging: Automatic charging prevents the battery from overcharging. Therefore, you can connect the charger to the battery indefinitely. Class 3 chargers are suitable for most battery types, including calcium, gel and AGM, wet batteries. Can help restore drained and sulfated batteries. Battery Type: Most types of lead acid batteries include calcium, GEL and AGM, wet, EFB, etc. Switch mode technology: yes Polarity protection: Yes Output short circuit protection: yes Non-Battery Link Protection: Yes Overvoltage protection: Yes Over temperature protection: Yes Cold fan Package Included: 1x12V 6A Intelligent Charger 1 x Manual (we will provide adapter according to delivery country) Click here for more deals iMars Green 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Aci iMars Green 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Aci

12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B Package weight: 0.88 kg Description: The difference between manual and automatic mode: 1. Manual: It can be used for small capacity, Low temperature(under 0 ° C) and large Internal resistancethe battery, charging current is bigger than automatic so it take less time than automatic, but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can’t more than 1 hour! 2. Automatic:pulg AC power first then connect battery with charger, it will recognize volgate automatic,telligent and convenient. Highly recommended: in the winter(under 0 ° C), use automatic mode to charge full first then use manual mode for 0.5-1 hours. 3. LED screen: it shows both charging voltage and current, 4. Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off 5. Red is anode,black is cathode Specification: Input Voltage: AC150-250V Output voltage: 12V/24V automatic Suitable capacity: 6AH-200AH Full load conversion efficiency: 93% Power: 220W Frequency: 50-60HZ Length of power cord wire:125cm Plug: US Plug Type: Charger Automatic, LED Light, Plug in, Portable, Reverse Polarity Protection, Safety Switch, Trickle Charging Stage: 1. Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; 2. Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger’s current and output voltage accurate,avoid overcharge; 3. Trickle charge mode: when the battery voltage and current is approaching the set voltage and current,it will turn to trickle floating charge from automatic mode, it means charge full,also can be charged with floating mode. Package Included: 1 X Charger 1 X User Manual 2 X Replace Clips Click here for more deals 12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B 12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B

BatteryMate 150-9 Battery Charger - 12v The BatteryMate 150-9 Battery Charger is a load tester & charger and automatic desulfater for all 12V lead-acid batteries from 2 to 45Ah. Features Quick new battery activation ¿ 30 minute activation charge for new batteries that have received acid just prior to charging, such as STD flooded batteries with removable filler caps and AGM-MF ¿dry-charged¿ batteries that are delivered with a separate custom acid pack. True load tester selectable from 15A to 150A ¿ Automatically tests battery cranking amps up to 330CCA. 3 second test simulates normal engine cranking / start, 15 second test checks battery health. Powersport specific charging algorithm ¿ 4 step charging method recovers any 12V battery. MF mode allows up to 16.9V for ¿dry-charged¿ AGM batteries. Temperature regulated charging ¿ Charge voltage is adjusted according to ambient temperature. (-4mV/°C/cell above/below 68°F/20°C). Accurate voltage sensing ¿ Charge leads have integrated voltage sense wires for exact voltage measurement at the battery. Easy to use ¿ 6 position combination selector allows selection of correct test and charge current for connected battery. TEST and then select max. charge time according to result, press CHARGE button. Program completes charging automatically and then tests the battery. Specifications Charging AMPS 9A maximum; 1, 2, 3, 5, 7, 9 Amp selection Testing AMPS 150A maximum; 15, 35, 50, 70, 100, 150 Amp selection Use Indoor / workshop environment (lowest temperature: -4°F / -20°C) Save Low Volt Start of 1V + high power desulphation recovery Ideal For STD, AGM & GEL 12V batteries from 2 ¿ 40Ah Input Selectable 110-120VAC / 220-240VAC 50-60Hz, with ON/OFF power switch and replaceable fuse protection Style Vented industrial table top case with wall mount option (TS-218), 6ft / 180cm AC supply lead and 1 pair high current 6ft / 180cm charge leads ending in heavy duty battery clamps. BatteryMate 150-9 Battery Charger User Manual

Description: 1. The MXS 5.0 is an advanced microprocessor controlled battery charger with automatic temperature compensation built in providing unrivalled performance on batteries from 1.2Ah up to 110Ah. 2. The MXS5.0 solves a broad range of battery problems and is the ideal charger for the user with high demands. 3. AGM mode is perfect for maximizing performance and life of most Stop-Start batteries. Feature: 1. Features of the MXS 5.0 include diagnosis of battery condition to establish if it can receive and retain charge, automatic desulphation programmer and a special reconditioning function that will revive and restore deeply discharged and stratified batteries. 2. The built in temperature compensation ensures ideal charging performance even in the most extreme conditions. 3. Float/Pulse maintenance makes the MXS 5.0 ideal for long-term maintenance. The entire process of battery testing, charging and maintenance is easily followed on the clear LED display. 4.The MXS 5.0 is a fully automatic "connect and forget" 12V charger with 8 charging steps. 5.Offers selectable SMALL BATTERY, and NORMAL BATTERY programs. The RECOND and AGM options operate individually or together in both SMALL BATTERY and NORMAL BATTERY programs, providing great flexibility for the user. Wide charging range on all lead-acid battery types from 1.2Ah up to 110Ah with additional maintenance capability to 160Ah. Splash proof and dust proof. The MXS 5.0 is easy and safe to use, protects vehicle electronics, is spark-free, reverse polarity protected and short circuit proof. Specification: Volt 12V Rated Voltage AC 220–240VAC, 50–60Hz Charging voltage SMALL, NORMAL: 14.4V, COLD/AGM: 14.7V, RECOND: 15.8V Minimun battery voltage 2.0V Charging current 5A max Current, mains 0.6A rms (at full charging current) Back current drain Ripple Ambient temperature -20°C to +50°C, output power is reduced automatically at high temperatures Charger type 8 step, fully automatic charging cycle Battery types All types of 12V lead-acid batteries (WET, MF, Ca/Ca, AGM and GEL) Battery capacity 1.2–110Ah up to 160Ah for maintenance Dimensions 150 x 65 x 38mm (L x W x H) Weight 0.6kg User Mannual in ten languages (EN, DE, FR, ES, IT, NL, SE, DK, NO, FI) Package Included: 1 X Charger Unit; 2 X User Manual

Description: The difference between manual and automatic mode: 1. Manual: It can be used for small capacity, Low temperature(under 0 ° C) and large Internal resistancethe battery, charging current is bigger than automatic so it take less time than automatic, but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can’t more than 1 hour! 2. Automatic:pulg AC power first then connect battery with charger, it will recognize volgate automatic,telligent and convenient. Highly recommended: in the winter(under 0 ° C), use automatic mode to charge full first then use manual mode for 0.5-1 hours. 3. LED screen: it shows both charging voltage and current, 4. Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off 5. Red is anode,black is cathode Specification: Input Voltage: AC150-250V Output voltage: 12V/24V automatic Suitable capacity: 6AH-200AH Full load conversion efficiency: 93% Power: 220W Frequency: 50-60HZ Length of power cord wire:125cm Plug: US Plug Type: Charger Automatic, LED Light, Plug in, Portable, Reverse Polarity Protection, Safety Switch, Trickle Charging Stage: 1. Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; 2. Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger’s current and output voltage accurate,avoid overcharge; 3. Trickle charge mode: when the battery voltage and current is approaching the set voltage and current,it will turn to trickle floating charge from automatic mode, it means charge full,also can be charged with floating mode. Package Included: 1 X Charger 1 X User Manual 2 X Replace Clips

Hawkins Battery Charger - Auto Pro 50 - 24v The Hawkins Auto Pro 50 Battery Charger is a fully regulated and temperature compensated charger that is available in both 12V and 24V versions. The charger is specifically intended to charge large capacity batteries rapidly and safely and may be used in standby mode - i.e. left connected to the battery for lengthy periods - without fear of overcharging and damaging the battery. It may be used to charge both conventional flooded and/or sealed batteries. The charger is reverse polarity protected to prevent serious damage that can occur from wrong connections. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. Input Current 10,54 A a.c. Output Voltage 28.8V d.c. Float Voltage 27V d.c. Output Current 50A Min Ah 100Ah Dimensions 360 x 365 x 325 mm Weight 30,0 kg

CTEK Battery Charger - 12V Multi XS 25000   The CTEK 12V Multi XS 25000 Battery Charger  is a professional 12V charger. It offers efficient and fast charging and is ideal charging and maintenance charging of 12V vehicles and machinery. XS 25000 has no mode button, so it's just plug in main and connect battery cables to start charging. The XS 25000 is equipped with all necessary features and functions to solve a broad range of battery related problems. It offers features such as battery diagnosis that shows if a battery can receive and retain a charge, unique maintenance charging, and a temperature sensor for optimized charging regardless of the weather conditions. It also has a power supply mode which allows the battery to be disconnected from the vehicle without losing important configurations. The XS 25000 is a fully automatic 7-step charger that delivers 25A to 12 V batteries from 40—500 Ah. The charger is IP44 classified (outdoor use), designed to protect vehicle electronics, non-sparking, reverse polarity protected, and short-circuit proof.   Features   Fan 8 step charging Auto: Fully automatic for optimal charging 12V: For all lead-acid batteries Fully Charged Battery / Maintenance Charging   Specifications   Cooling Fan Volt 12V Rated Voltage AC 170—260VAC, 50—60Hz Charging Voltage 14.4V Charging Current 25A max Current, Mains 2.9A rms (at full charging current) Back Current Drain Ripple Ambient Temperature -20°C to +50°C, output power is reduced automatically at high temperatures Charger Type 8 step, fully automatic charging cycle Battery Types All types of 12V lead-acid batteries (WET, MF, Ca/Ca, AGM and GEL) Battery Capacity 50—500Ah Dimensions 235 x 130 x 65mm  Insulation Class IP44 Weight 1.9kg  

SELECTED OPTION: ADAPTOR: US CLICK HERE for more options in this item. Description: The difference between manual and automatic mode: Manual: It can be used for small capacity,Low temperature(under 0 ° C) and large Internal resistancethe battery,charging current is bigger than automatic so it take less time than automatic,but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can't more than 1 hour! Automatic:pulg AC power first then connect battery with charger,it will recognize volgate automatic,telligent and convenient. Highly recommended:in the winter(under 0 ° C),use automatic mode to charge full first then use manual mode for 0.5-1 hours. LED screen: it shows both charging voltage and current, Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off -Red is anode,black is cathode   Specification: Input Voltage: 110-250V Output voltage: 12V/24V automatic Current: 10A peak for 12V /7A peak for 24V Suitable Capacity: 10-100AH Power: 180W Frequency: 50-60HZ Length of Output Wire: 50-60cm Length of Input Wire: 120cm Type: Charger Features: Automatic, LED light, plug in, portable, reverse polarity protection, safety switch, trickle   Charging Stage: Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger's current and output voltage accurate,avoid overcharge; Trickle charge mode: when the battery voltage and current is approaching the set voltage and current, it will turn to trickle floating charge from automatic mode,it means charge full,also can be charged with floating mode.   Package Included: 1 X Charger 1 X User Manual

Hawkins Battery Charger - Auto Pro 10 - 12/24v The Hawkins Auto Pro 10 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Current Selector 5A 10A Rated Input Voltage 230V a.c. 230V a.c. Rated Input Current 0,7 A a.c. 1,1 A a.c. Rated Output Voltage 12V d.c. 12V d.c. Rated Ouput Current 6A d.c. 10A d.c. Current Selector 5A 10A Rated Input Voltage 230V a.c. 230V a.c. Rated Input Current 1.2A a.c. 1.7A a.c. Rated Output Voltage 24V d.c. 24V d.c. Rated Ouput Current 6A d.c. 10A d.c. Dimensions 245 x 145 x 150 mm Weight Nett/Gross 6,0/6,4

Hawkins Battery Charger - Pro 615 The Hawkins Pro 615 Battery Charger is ideally suited for small businesses offering a TV battery recharging service or large vehicle workshops where up to 6 x 12V batteries need to be charged simultaneously. 3 batteries are connected in series and this is connected to 1 set of charging leads (Bank 1). A second set of 3 batteries connected in series can be connected to the second set of charging leads (Bank 2). A voltage selector switch allows the user to select 12V, 24V or 36V for each bank. The charge rate selector is used to control the current on each bank. Each bank is protected on the input side by an internal mains fuse and on the output side by a circuit breaker and a fuse. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Current Selector 5 5 Rated Input Current 0.95A a.c. 1.7A a.c. Rated Output Voltage 14V d.c. 27V d.c. Rated Output Current 10A d.c. 10A d.c. Rated Input Voltage 230V a.c. Volt Selector 36V Current Selector 5 Rated Input Current 2.7A a.c. Rated Output Voltage 43V d.c. Rated Output Current 10A d.c. Dimensions 445 x 200 x 220mm Weight 17.4kg

Hawkins Battery Charger - Power 10 The Hawkins Power 10 Battery Charger is made from high quality materials and components. These chargers are designed for flooded lead acid batteries. The Power 10 charger has been designed especially for the descerning farmer, caravaner, powerski boater and householder who requires a reliable and robust battery charger. It will continue to trickle past the nominal 13,8V of the fully charged battery and must be monitored periodically. These chargers are not automatic and therefore not recommended for sealed batteries. The Power range of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Conforms to SABS IEC 335-2-29 Thermal overload protection Automatic circuit breaker protection Easy to follow instructions Two year warranty Specifications Rated Input Voltage 230V a.c. Rated Input Current 0.6 A a.c. Rated Output Voltage 12V d.c. Rated Output Current 6.4 A d.c. Min Ah 20Ah Dimensions 245 x 145 x 150mm Weight Nett/Gross 4.7/4.8kg

iMars 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Batt Package weight: 0.45 kg Description: iMars™ 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Battery Agm Gel Wet Microprocessor Control (CPU). 1. 3-STAGE AUTOMATIC CHARGING: 2. This is a fully automatic battery charger with 3 charge stages. 3. Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. 4. 3-stage chargers are suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. 5. Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. Feature: Switchmode technology: Yes Polarity protection: Yes Output short protection: Yes Non battery link protection: Yes Over voltage protection: Yes Over temperature protection: Yes Cooling: Fan Specification: Input voltage: 100-240V AC, 50-60Hz Rated output: 12V DC, 5-6A Max. Minimum start voltage: 8.0V Battery range: 4-100Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85%. Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 150×85×60mm Note: This Charger is for battery capacity between 4AH to 100AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X iMars™ 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Battery Agm Gel Wet Click here for more deals iMars 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Batt iMars 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Batt

iMars 12V 6A Blue Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Package weight: 0.45 kg Description: iMars™ 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Battery Agm Gel Wet Microprocessor Control (CPU). 1. 3-STAGE AUTOMATIC CHARGING: 2. This is a fully automatic battery charger with 3 charge stages. 3. Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. 4. 3-stage chargers are suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. 5. Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. Feature: Switchmode technology: Yes Polarity protection: Yes Output short protection: Yes Non battery link protection: Yes Over voltage protection: Yes Over temperature protection: Yes Cooling: Fan Color: Blue Adapter Plug: US/EU Specification: Input voltage: 100-240V AC, 50-60Hz Rated output: 12V DC, 5-6A Max. Minimum start voltage: 8.0V Battery range: 4-100Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85%. Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 150×85×60mm Note: This Charger is for battery capacity between 4AH to 100AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X iMars™ 12V 6A Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid Battery Agm Gel Wet Click here for more deals iMars 12V 6A Blue Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid iMars 12V 6A Blue Pulse Repair LCD Battery Charger For Car Motorcycle Lead Acid