Hawkins battery charger power

Hawkins Battery Charger - Power 10 The Hawkins Power 10 Battery Charger is made from high quality materials and components. These chargers are designed for flooded lead acid batteries. The Power 10 charger has been designed especially for the descerning farmer, caravaner, powerski boater and householder who requires a reliable and robust battery charger. It will continue to trickle past the nominal 13,8V of the fully charged battery and must be monitored periodically. These chargers are not automatic and therefore not recommended for sealed batteries. The Power range of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Conforms to SABS IEC 335-2-29 Thermal overload protection Automatic circuit breaker protection Easy to follow instructions Two year warranty Specifications Rated Input Voltage 230V a.c. Rated Input Current 0.6 A a.c. Rated Output Voltage 12V d.c. Rated Output Current 6.4 A d.c. Min Ah 20Ah Dimensions 245 x 145 x 150mm Weight Nett/Gross 4.7/4.8kg

Hawkins Battery Charger - Fence Pro 3 The Hawkins Battery Charger - Fence Pro 3 is indended to meet market requirments for a low cost automatic battery charger. The unit is made from hight quality materials and components which conforms to IEC 335-2-29 on perfomance, safety, and electromagnetic interference. It is designed specifically forflooded lead acid batteries and sealed batteries. The Fence Pro is an automatic charger which delivers its rated current untill the voltage on the battery reaches a preset level. The charger will then switch off, wait for the battery to drop down to the minimum set point, and then switch on again. The charger will cycle in this fashion indefinitely. The charger is electronically controlled and may be left permanently attached to the battery without danger, provided the battery's condition is monitored on a regular basis. Potential free clamps avoid sparking when connecting or removing the battery clamps in a potentially volatille enviroment. The charger is reverse polarity protected. The charger is internally fused and has protection for over voltage transients. The Smart range of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Conforms to SABS IEC 335-2-29 Thermal overload protection Replaceable fuse protection on output side Flame retardant plastic caing Transient Voltage Suppression Portable Two year warrently Specifications Input Voltage: 230VAC Input Current: 0,34 AAC Output Voltage: 12VDC Output Current: 3.2ADC Dimensions (WxHxL): 190 x 95 x 85 mm Weight Nett/Gross: 1.75/1.9 kg

Hawkins Battery Charger - Inverter 350W The Hawkins Battery Charger - Inverter 350W offers a range of DC to AC inverters practically sized for domestic, commercial and leisure applications. The CPI 12035, DPI 12100 and CPI 12100C inverters are modified sine wave inverters. We also offer a range of pure sinewave inverters ranging from 2.5KVA to 8KVA that has built in chargers. Typical aplications would include camping, portable power for power tools, farming, alternative energy for domestic use, field reseach, holiday resorts, solar and wind generating power systems, etc. Our sine wave inverters are not portable and would normally be permanently installed. Features Nominal Voltage: 12V Low BatteryAlarm: 10.7V High Voltage Alarm: 16V Efficiency: 90% Protection: Over Teperature >65 deg. centigrade Short crcuit Overload Dimensions: 70 x 48 x 155 Weight: 0.61 kg Specifications Power: 350 watt Start-up: 800 watt Voltage: 230VAC Regulation: 8% (rms) Frequency: 50Hz (1%) Waveform: Modified Sine

Hawkins Battery Charger - Auto Pro 5 - 24v The Hawkins Auto Pro 5 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Rated Input Voltage 230V a.c. Rated Input Current 1,1 A a.c. Rated Output Voltage 24V d.c. Rated Output Current 6A d.c. Float Voltage 27V d.c. Dimensions 245 x 145 x 150 mm Weight Nett/Gross 5,0/5,3 kg

Hawkins Battery Charger - Pro 224 The Hawkins Pro 224 Battery Charger is a powerful engine starter and battery charger combination. It is intended for table top use at home or in small businesses and garages. The Pro 224 will deliver an engine start aid of 200A c.c. which is sufficient to start petrol and diesel engines up to 2-litre capacity. In charger mode, the charger will charge 12V and 24V batteries. Selection is made by connecting the charging cable to either the 12V stud or 24V stud on the front panel. The transformer is protected by an automatic reset thermal circuit breaker and a 12.5A mains fuse. The output side is protected by a replaceable 80A fuse to guard against incorrect polarity or too high a charging current. Two rocker switches allow for both Battery Charge/Engine Start and HIGH/LOW charging selection. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Battery Charger Switch Position LOW LOW Input Current 0.55A a.c. 1.2A a.c. Ouput Voltage 12V d.c. 24V d.c. Ouput Current 7.2A d.c. 8A d.c. Switch Position HIGH HIGH Input Current 1.48A a.c. 3A a.c. Ouput Voltage 12V d.c. 24V d.c. Output Current 18.5A d.c. 19A d.c. Engine Starter Switch Position LOW LOW Input Current 2.87A a.c. 6.5A a.c. Output Voltage 12V d.c. 24V d.c. Output Current 35.3A d.c. 39A d.c. Switch Position HIGH HIGH Input Current 4.9A a.c. 10.9A a.c. Output Voltage 12V d.c. 24V d.c. Output Current 56A d.c. 62A d.c. Dimensions 320 x 220 x 180mm Weight 10.5kg

Hawkins Battery Charger - Auto Pro 10 - 12/24v The Hawkins Auto Pro 10 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Current Selector 5A 10A Rated Input Voltage 230V a.c. 230V a.c. Rated Input Current 0,7 A a.c. 1,1 A a.c. Rated Output Voltage 12V d.c. 12V d.c. Rated Ouput Current 6A d.c. 10A d.c. Current Selector 5A 10A Rated Input Voltage 230V a.c. 230V a.c. Rated Input Current 1.2A a.c. 1.7A a.c. Rated Output Voltage 24V d.c. 24V d.c. Rated Ouput Current 6A d.c. 10A d.c. Dimensions 245 x 145 x 150 mm Weight Nett/Gross 6,0/6,4

Hawkins Battery Charger - Pro 324 The Hawkins Pro 324 Battery Charger is a powerful engine starter and battery charger combination. The Pro 324 will deliver an engine start aid of 300A c.c. and is capable of charging 12V and 24V batteries. Selection is made by connecting the charging cable to either the 12V stud or 24V stud on the top panel. The transformer is protected by an automatic reset thermal circuit breaker and a 12.5A mains fuse. The output side is protected by a replaceable 80A fuse to guard against incorrect polarity or too high a charging current. Two rocker switches allow for both Battery Charge/Engine Start and HIGH/LOW charging selection. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Current Selector 6 6 Battery Charger Switch Position LOW LOW Input Current 3A a.c. 6.9A a.c. Ouput Voltage 12V d.c. 24V d.c. Ouput Current 37A d.c. 44A d.c. Switch Position HIGH HIGH Input Current 4.5A a.c. 9.5A a.c. Ouput Voltage 12.5V d.c. 25V d.c. Output Current 49A d.c. 54A d.c. Min Battery Capacity 35Ah 35Ah Dimensions 260 x 540 x 220mm Dimensions with Handle 260 x 840 x 220mm Weight 17.5kg

Hawkins Battery Charger - Auto Pro 50 - 24v The Hawkins Auto Pro 50 Battery Charger is a fully regulated and temperature compensated charger that is available in both 12V and 24V versions. The charger is specifically intended to charge large capacity batteries rapidly and safely and may be used in standby mode - i.e. left connected to the battery for lengthy periods - without fear of overcharging and damaging the battery. It may be used to charge both conventional flooded and/or sealed batteries. The charger is reverse polarity protected to prevent serious damage that can occur from wrong connections. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. Input Current 10,54 A a.c. Output Voltage 28.8V d.c. Float Voltage 27V d.c. Output Current 50A Min Ah 100Ah Dimensions 360 x 365 x 325 mm Weight 30,0 kg

Hawkins Battery Charger - Pro 615 The Hawkins Pro 615 Battery Charger is ideally suited for small businesses offering a TV battery recharging service or large vehicle workshops where up to 6 x 12V batteries need to be charged simultaneously. 3 batteries are connected in series and this is connected to 1 set of charging leads (Bank 1). A second set of 3 batteries connected in series can be connected to the second set of charging leads (Bank 2). A voltage selector switch allows the user to select 12V, 24V or 36V for each bank. The charge rate selector is used to control the current on each bank. Each bank is protected on the input side by an internal mains fuse and on the output side by a circuit breaker and a fuse. The Pro series of chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Not recommended for sealed batteries. Features Thermal overload protection Replaceable fuse protection on output side Automatic circuit breaker protection Robust, epoxy coated steel cabinet Two year warranty Specifications Input Voltage 230V a.c. 230V a.c. Battery Voltage 12V 24V Current Selector 5 5 Rated Input Current 0.95A a.c. 1.7A a.c. Rated Output Voltage 14V d.c. 27V d.c. Rated Output Current 10A d.c. 10A d.c. Rated Input Voltage 230V a.c. Volt Selector 36V Current Selector 5 Rated Input Current 2.7A a.c. Rated Output Voltage 43V d.c. Rated Output Current 10A d.c. Dimensions 445 x 200 x 220mm Weight 17.4kg

Hawkins Battery Charger - Auto Pro 5 - 12v The Hawkins Auto Pro 5 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Rated Input Voltage 230V a.c. Rated Input Current 0,6 A a.c. Rated Output Voltage 12V d.c. Rated Output Current 6A d.c. Float Voltage 13,5V d.c. Dimensions 245 x 145 x 150 mm Weight Nett/Gross 4,1/4,35 kg

Hawkins Battery Charger - Auto Pro 35 The Hawkins Auto Pro 35 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Rated Input Voltage 230V a.c. Rated Input Current 3,3 A a.c. Rated Output Voltage 12V d.c. Rated Output Current 35A d.c. Dimensions 230 x 220 x 285 mm Weight Nett/Gross 11,1/11,5 kg

Hawkins Battery Charger - Auto Pro 20 - 36v The Hawkins Auto Pro 20 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Rated Input Voltage 230V a.c. Rated Input Current 6,0 A a.c. Rated Output Voltage 36V d.c. Rated Output Current 19A d.c. Dimensions 230 x 220 x 285 mm Weight Nett/Gross 14,1/14,5 kg

Hawkins Battery Charger - Auto Pro 20 - 24v The Hawkins Auto Pro 20 Battery Charger is a three stage temperature compensated fully automatic microprocessor controlled unit. The three charging stages are identified as Bulk, Absorption and Float. These chargers are suitable for charging all types of Lead/Calcium -, Flooded-, Maintenance Free-, Sealed-, Gel and AGM (Absorbent Glass Mat) batteries. The Auto Pro chargers were designed in compliance with IEC 335-2-2 and has a two year limited warranty against defects in materials and workmanship. Features Thermal overload protection Replaceable fuse protection on output side Robust, epoxy coated steel cabinet Two year warranty Not suitable to be supplied from generators unless generator has low distortion 50Hz 230Vac output Specifications Rated Input Voltage 230V a.c. Rated Input Current 4,1 A a.c. Rated Output Voltage 24V d.c. Rated Output Current 20A d.c. Dimensions 230 x 220 x 285 mm Weight Nett/Gross 11,1/11,5 kg

Buy Battery Charger Power Supply For Karcher WV50 WV75 Window Vacuum Cleaners - US Plug for R119.00

Buy 110-240V 26.1V 0.78A Battery Charger Power Supply Adapter For Cordless Dyson V8 V7 V6 Vacuum Cleaner for R306.00