E300 inch

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5" screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD.     a.  Check around the area under the steering wheel for an OBD plug     b.  Contact your vehicle manufacturer or search online     c.  Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn't a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle's engine and ensure power switch is in the on position. 4. HUD will power on with engine     a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly.     b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you're satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD's reflection, reposition using the nonslip mat. Technical Parameter:  Environment Temperature  -40℃ ~ +80℃  Barometric Press  86 ~ 106KPa  Relative Humidity  10% ~ 95%  Environment Noise  ≤60dB  Alarm Decibel  ≥30dB(A)  Work Voltage  9V ~ 16Vdc(12Vdc/400mA)  Product Dimensions  12.5 * 7.5 * 1.5(cm)  Product Weight  110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5” screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn’t a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle’s engine and ensure power switch is in the on position. 4. HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you’re satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD’s reflection, reposition using the nonslip mat. Technical Parameter: Environment Temperature -40??~ +80??/td> Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise ≤60dB Alarm Decibel ≥30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5” screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn’t a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle’s engine and ensure power switch is in the on position. 4. HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you’re satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD’s reflection, reposition using the nonslip mat. Technical Parameter: Environment Temperature -40￢ﾄﾃ ~ +80￢ﾄﾃ Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise ≤60dB Alarm Decibel ≥30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

Buy E300 5.5 inch Car OBDII / EUOBD HUD Vehicle-mounted Head Up Display Security System, Support Speed & for R957.61

This item is sold brand new. It is ordered on demand from our supplier and is usually dispatched in 10 to 15 working days. We urge you to please read shipping details before placing your order. --------------------------------------- 1. Plug and Play connectivity with any OBDII or EUOBD capable vehicle; 2. 2D visual effect 3. 5.5 inch screen 4. Multi colour design makes the screen easier to read highlight important details for quick viewing 5. The use of nanotechnology to eliminate unwanted reflections making the information easier to read; 6. Ability to display a huge range of car statistics including: speed engine rotational speed water temperature battery voltage instantaneous fuel consumption average fuel consumption local time single driving time mileage measurement shift reminder fatigued driver reminder low voltage alarm high temperature alarm speed alarm engine fault alarm fault code elimination ability to change units e.g. Kilometer/mile 7. Auto power on and off with the vehicle 8. Automatic and manual brightness adjustment mode --------------------------------------- See what else we're selling

Feature: 1.2D Vision reflection display make your view more comfortable, more real. 2.Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time, mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. 3.Plug and Play connectivity with any OBDII or EUOBD capable vehicle. 4.Multi colour design makes the screen easier to read highlight important details for quick viewing, the use of nanotechnology to eliminate unwanted reflections making the information easier to read. 5.Auto power on and off with the vehicle, automatic and manual brightness adjustment mode. HUD installation procedure: 1.Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn't a deciding factor) 2.Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3.Start vehicle's engine and ensure power switch is in the on position. 4.HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Note:  This HUD is just compatible with OBDII standards or EU OBD.Open the engine hood and find the sticker below it, if it has words like OBDII CERTIFIED, then it can be installed. Package Included: 1 X HUD 1 X ODB Data Line 1 X Reflection Film 1 X Anti-slip Pad 1 X English User Manual   Specificaion: Screen 5.5 inches Working Voltage DC9-16V (DC12V 400mA) Environment Temperature -40 degree centigrade ~ +80 degree centigrade Atmospheric Pressure 86-106KPa Relative Humidity 10%-95% Environmental Noise ≤60dB(A) Alarm Sound Level ≥30dB(A) Size Approx. 13*7.5*1.5cm

Car Front Bumper Tow Hook Cover Cap for Mercedes E-class E300 E350 E500 2128850126 Specification: Color: Black Material: Plastic Placement: Front Part Number: 2128850126 Fitment: Fit for Mercedes E-class W212 E300 E350 E400 E500 (The Compatibility Is Just For Reference. Please Compare the size with Your Original One Before Purchasing.) Note: 1. (IMPORTANT) No Instructions Included. Professional Installation Is Highly Recommended. 2. Please check the size measurement chart carefully before making payment. 3. Please allow 0.5-1 inch difference due to manual measurement.(1 inch=2.54cm) 4. The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding. Package Included: 1 X Front Bumper Tow Hook Cover