E300 car hud

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5" screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD.     a.  Check around the area under the steering wheel for an OBD plug     b.  Contact your vehicle manufacturer or search online     c.  Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn't a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle's engine and ensure power switch is in the on position. 4. HUD will power on with engine     a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly.     b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you're satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD's reflection, reposition using the nonslip mat. Technical Parameter:  Environment Temperature  -40℃ ~ +80℃  Barometric Press  86 ~ 106KPa  Relative Humidity  10% ~ 95%  Environment Noise  ≤60dB  Alarm Decibel  ≥30dB(A)  Work Voltage  9V ~ 16Vdc(12Vdc/400mA)  Product Dimensions  12.5 * 7.5 * 1.5(cm)  Product Weight  110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5” screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn’t a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle’s engine and ensure power switch is in the on position. 4. HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you’re satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD’s reflection, reposition using the nonslip mat. Technical Parameter: Environment Temperature -40??~ +80??/td> Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise ≤60dB Alarm Decibel ≥30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

E300 Car HUD Head Up Display 5.5 inch with OBD OBD2 Interface Plug HUD Main Feature: 5.5” screen. 2D visual effect. Auto power on and off with the vehicle. Automatic and manual brightness adjustment mode. Plug and Play connectivity with any OBDII or EUOBD capable vehicle. Multi colour design makes the screen easier to read highlight important details for quick viewing. The use of nanotechnology to eliminate unwanted reflections making the information easier to read. Ability to display a huge range of car statistics including: speed, engine rotational speed, water temperature, battery voltage, instantaneous fuel consumption, average fuel consumption, local time,single driving time,mileage measurement, shift reminder, fatigued driver reminder, low voltage alarm, high temperature alarm, speed alarm, engine fault alarm, fault code elimination, ability to change units e.g. Kilometre/mile. HUD Installation Procedure: 1. Ensure your vehicle is OBDII compatible or EUOBD. a. Check around the area under the steering wheel for an OBD plug b. Contact your vehicle manufacturer or search online c. Open the bonnet and look for a OBDII compatible sticker (this is NOT on all OBDII compatible cars, therefore isn’t a deciding factor) 2. Locate the 16 pin diagnostic link. This is usually located in the area under the steering wheel. 3. Start vehicle’s engine and ensure power switch is in the on position. 4. HUD will power on with engine a. If the HUD displays vehicle voltage, fuel consumption, speed and rotational speed the unit has installed correctly. b. Failing the above: Wait up to one minute for software to sync and confirm OBD cable is plugged in properly. Reflective Film Installation: 1. Place the supplied non-slip mat in the desired position on the dashboard with the HUD on top. 2. Observing where the HUD reflects place the reflective film in position. a. Ensure the surface is clean and dry before installing the film; b. Remove the back protective side marked (1) and attach the film to the clean windscreen; c. Once you’re satisfied with the location use a credit card or similar to remove any bubbles or air pockets that remain; d. Remove the front side marked (2), if you need to adjust the HUD’s reflection, reposition using the nonslip mat. Technical Parameter: Environment Temperature -40￢ﾄﾃ ~ +80￢ﾄﾃ Barometric Press 86 ~ 106KPa Relative Humidity 10% ~ 95% Environment Noise ≤60dB Alarm Decibel ≥30dB(A) Work Voltage 9V ~ 16Vdc(12Vdc/400mA) Product Dimensions 12.5 * 7.5 * 1.5(cm) Product Weight 110g Package Included: 1 X E300 Head Up Display 1 X Reflective Film 1 X OBD Connecting Line 1 X User Manual

Car HUD Head Up Display KM/h&MPH Speeding Warning OBD2 System Feature: 1. Plug and play. HUD can auto adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System).  2. Comprehensive display. HUD can display many parameters at the same time as follows, vehicle speed, engine speed,      water tempe- rature (voltage, throttle valve position, ignition advance angle, time of 100 km acceleration), fuel consumption,     mileage, low fuel tips, engine failure. 3. Diversiform display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. 4. Free switch. Km and mile can be switched freely to meet the need of inch auto meter. 5. Suitable size. The display area is 5.5 inches which is very clear for driver to read data.  6. Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Moreover,  we pre- serve the hand switch function to controlthe HUD.  7. Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer.  8. Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver.  9. Flexible brightness adjustment. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment.  Specification: Service conditions:Environment temperature: -400C—+800C Barometric  press: 86—106 KPa Relative humidity: 10%—95%Environment voice: Alarm of sound level:> =30dB(A) Work voltage: 9V~16Vdc(12Vdc/400mA)  Size of product: 14x85x147 (mm) All of the electronic components are conform to ROSH standards.  Conforming to the China Compulsory Certification. Remarks:  Open and look for the sticker under the engine hood, can use this product if it has the sticker with OBDII CERTIFIED.  1. Check if it has the automobile diagnostic socket under the steering wheel(most of car in China has this socket manufactured after the year 2006.  2. Identify the car's 16-pin diagnostic socket, connecting the OBDII cable to the 16-pin diagnostic socket if it has this socket.  3. Put the non-slip pad onto the instrument pane, then put HUD on the non-slip pad, you can adjust the angle an position.  4. The reflective film may be affixed to the forward position of HUD and stick to the front windshield, ensure that the information, such as car speed can be projected to the reflective film.  Package Included: 1 x HUD Interface 1 x OBD2 Interface 1 x Reflective Film 1 x Mat 1 x User Manual

I5 6 inch Car HUD Head Up Display OBDII Interface Feature: 1. Detecting car’s OBDII interface automatically and all car with OBD II or EUOBD are OK, plug and play; 2. Car speed, engine speed, water temperature, voltage/ throttle position/ Ignition angle/ one-hundred-kilometer acceleration time, instant fuel consumption, average fuel consumption, mileage, fuel shortage reminding, engine faulty, shift reminding, etc. are displayed; 3. Normal display mode, high-speed display mode and automatic display mode are set by yourself; 4. Kilometers and miles are free to switch, which greatly facilitates the dashboard of British Standard; 5. 6 inches display area, easy to read; 6. Switch on and off automatically, HUD start when car starting, HUD shutdown when the engine is turning off to protect the car battery effectively; at the same time, you can switch on and off HUD by Manually Shutdown to protect the battery safety; 7. Single-stage and four-stage overspeed alarm for driving safely; 8. Engine speed alarming so that you can shift timely to save fuel, also has a special significance for the novice; 9. Automatic and manual brightness adjustment mode, no dazzling; 10. Compass (this function is optional), the precise position, car does not get lost; Accurately determining the position and not get lost. Installation Instruction: 1. Make sure if your car complies with OBD II (or EU OBD) interface standard; 2. Open up the engine hood and look for the OBDII sticker. If there is a sticker of "OBDII CERTIFIED", then you can use our HUD. You can also check if your car have a diagnostic Interface(the vast majority of cars made in china after 2006 have the diagnostic Interface). 3. If your car has a diagnostic Interface of 16PIN(Figure 3), then plug the OBDII cable with the diagnostic Interface of 16PIN. 4. Put the non-slip mat on the relatively flat position of the car console. Then you put HUD on the non-slip mat and adjust HUD. 5. Reflective film can be attached to the front windshield above HUD so that you can read the parameters form the reflective film. Remarks: tips of sticking the reflective film A. Firstly spray some water on the position of sticking the reflective film; B. Remove the protective layer of the film, then attach to the corresponding position; C. Adjust the location, then use a small scraper or a smooth object to scrape the surface of the film; D. After a few minutes, the moisture will evaporate, then gently wipe off the water droplets and dust. 6. Power-on test You switch on HUD and HUD shows the current car voltage. Then HUD searches the car computer system. If HUD displays data, such as car speed, engine speed etc, it indicates that the product has been installed successfully. Technical Indicator: Ambient Temperature - 40??nbsp;~ + 80??/td> Relative Humidity 10% ~ 95% Environmental Noise ≤ 60 db (A) Alarm Sound Level ≥30 db (A) Working Voltage 9V ~ 16VDC (12Vdc/400mA) Size 155 * 93 * 15.7 (mm) Product Weight 80g Package Included: 1 X I5 6 inch HUD Head Up Display

I5 6 inch Car HUD Head Up Display OBDII Interface Feature: 1. Detecting car’s OBDII interface automatically and all car with OBD II or EUOBD are OK, plug and play; 2. Car speed, engine speed, water temperature, voltage/ throttle position/ Ignition angle/ one-hundred-kilometer acceleration time, instant fuel consumption, average fuel consumption, mileage, fuel shortage reminding, engine faulty, shift reminding, etc. are displayed; 3. Normal display mode, high-speed display mode and automatic display mode are set by yourself; 4. Kilometers and miles are free to switch, which greatly facilitates the dashboard of British Standard; 5. 6 inches display area, easy to read; 6. Switch on and off automatically, HUD start when car starting, HUD shutdown when the engine is turning off to protect the car battery effectively; at the same time, you can switch on and off HUD by Manually Shutdown to protect the battery safety; 7. Single-stage and four-stage overspeed alarm for driving safely; 8. Engine speed alarming so that you can shift timely to save fuel, also has a special significance for the novice; 9. Automatic and manual brightness adjustment mode, no dazzling; 10. Compass (this function is optional), the precise position, car does not get lost; Accurately determining the position and not get lost. Installation Instruction: 1. Make sure if your car complies with OBD II (or EU OBD) interface standard; 2. Open up the engine hood and look for the OBDII sticker. If there is a sticker of "OBDII CERTIFIED", then you can use our HUD. You can also check if your car have a diagnostic Interface(the vast majority of cars made in china after 2006 have the diagnostic Interface). 3. If your car has a diagnostic Interface of 16PIN(Figure 3), then plug the OBDII cable with the diagnostic Interface of 16PIN. 4. Put the non-slip mat on the relatively flat position of the car console. Then you put HUD on the non-slip mat and adjust HUD. 5. Reflective film can be attached to the front windshield above HUD so that you can read the parameters form the reflective film. Remarks: tips of sticking the reflective film A. Firstly spray some water on the position of sticking the reflective film; B. Remove the protective layer of the film, then attach to the corresponding position; C. Adjust the location, then use a small scraper or a smooth object to scrape the surface of the film; D. After a few minutes, the moisture will evaporate, then gently wipe off the water droplets and dust. 6. Power-on test You switch on HUD and HUD shows the current car voltage. Then HUD searches the car computer system. If HUD displays data, such as car speed, engine speed etc, it indicates that the product has been installed successfully. Technical Indicator: Ambient Temperature - 40￢ﾄﾃ ~ + 80￢ﾄﾃ Relative Humidity 10% ~ 95% Environmental Noise ≤ 60 db (A) Alarm Sound Level ≥30 db (A) Working Voltage 9V ~ 16VDC (12Vdc/400mA) Size 155 * 93 * 15.7 (mm) Product Weight 80g Package Included: 1 X I5 6 inch HUD Head Up Display

5.5inch X3 ELM327 Car HUD Head Up Display with Bluetooth Function OBD2 Interfac Package weight: 0.27 kg X3 5.5inch Car HUD Head Up Display with Bluetooth Function OBD2 Interface Plug This HUD built in ELM327 and with bluetooth version function. Not only you can use the HUD to read all the information on windowscreen, but also you can download OBD APP from Android phone to read more information. The methods are below: 1. Download OBD App from phone 2. Open bluetooth of phone to scan,when display“HUD bluetooth”, click connect. The password is 1234 3. Open OBD App, click setting and adapter to connect 4. When finish connection,back to OBD APP interface to read more information. Feature: 1.Plug and play. HUD can automatically adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System). 2.Comprehensive display. HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water temperature (voltage, throttle valve position, ignition advance angle, time of 100 km acceleration),fuel consumption, mileage, low fuel tips, engine failure. 3.Three display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. 4.Free switch. Km and mile can be switched freely. 5.Suitable size. The display area is 5.5 inches which is very clear for driver to read data. 6.Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Moreover, HUD can alsopower on and power off by manual, which is more easy to control HUD. 7.Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer. 8.Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver. 9.Flexible brightness adjustment. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment. Specification: 1. Service conditions: Environment temperature: -400￢ﾄﾃ ~ +800￢ﾄﾃ Barometric press: 86 ~ 106 KPa Relative humidity: 10% ~ 95% Environment voice: ≤60 dB(A) 2. Alarm of sound level: ≥30dB(A) 3. Work voltage: 9V~16Vdc(12Vdc/400mA) 4. Size of product: 150 * 85 * 14 (mm) 5. Weight of product: 278g (including the giftbox) Package Included: 1 X X3 Car HUD Display 1 X OBD II Interface 1 X English User Manual Click here for more deals 5.5inch X3 ELM327 Car HUD Head Up Display with Bluetooth Function OBD2 Interfac 5.5inch X3 ELM327 Car HUD Head Up Display with Bluetooth Function OBD2 Interfac

X3 5.5inch Car HUD Head Up Display with Bluetooth Function OBD2 Interface Plug This HUD built in ELM327 and with bluetooth version function. Not only you can use the HUD to read all the information on windowscreen, but also you can download OBD APP from Android phone to read more information. The methods are below: 1. Download OBD App from phone 2. Open bluetooth of phone to scan,when display“HUD bluetooth”, click connect. The password is 1234 3. Open OBD App, click setting and adapter to connect 4. When finish connection,back to OBD APP interface to read more information. Feature: 1.Plug and play. HUD can automatically adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System). 2.Comprehensive display. HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water temperature (voltage, throttle valve position, ignition advance angle, time of 100 km acceleration),fuel consumption, mileage, low fuel tips, engine failure. 3.Three display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. 4.Free switch. Km and mile can be switched freely. 5.Suitable size. The display area is 5.5 inches which is very clear for driver to read data. 6.Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Moreover, HUD can alsopower on and power off by manual, which is more easy to control HUD. 7.Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer. 8.Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver. 9.Flexible brightness adjustment. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment. Specification: 1. Service conditions: Environment temperature: -400￢ﾄﾃ ~ +800￢ﾄﾃ Barometric press: 86 ~ 106 KPa Relative humidity: 10% ~ 95% Environment voice: ≤60 dB(A) 2. Alarm of sound level: ≥30dB(A) 3. Work voltage: 9V~16Vdc(12Vdc/400mA) 4. Size of product: 150 * 85 * 14 (mm) 5. Weight of product: 278g (including the giftbox) Package Included: 1 X X3 Car HUD Display 1 X OBD II Interface 1 X English User Manual

GEYIREN A5 3.5 Inch Car HUD Windshield Projector Speedometer Overspeed GPS Satellite 2 Dispaly Mode Feature: 1.Available for any car, easy to install, plug and play. 2.Two mode display: reflect on windshield or directly see on the sit up HUD screen. 3. Screen 3.5 inch HD display. 4. Multi-color design makes the screen more abundant and easier to read. 5. Nano-technology to eliminate double reflections,more clear. 6. Rich Contents: speed,compass, speed alarm,free switch between km and miles. 7. Auto power on/off: HUD start and off with vehicle started and shutdown, effective protection of the car battery;retaining the manual switch mode,more easy to control HUD. 8. Automatic and manual brightness adjustment mode,driving without glare. Specification: 1. Brand Name:Geyiren 2. Type: Head up display A5 3. Voltage:12V 4. Wire or Wireless:wired 5. Color: Black 6. Material Type:ABS 7. Display type:Digital 8. Screen Size:3.5 inches 9. Color: black 10. Material: Plastic+PC 11. Working voltage:DV8-18V 12. Working Current:40mA 13. Sleeping current:15mA 14. Compass precision:±1° 15. Speed range:0-400KM 16. Real time precision:The same as satellite 17. 12V car charger:1000mA 18. System:Two Display system(HUD display&Screen Display) 19. OBDII Cable Length: about1.95m/ 76.77in 20. HUD size: 9 * 5.4 * 1.2cm / 3.6 * 2.2 * 0.5in 21. HUD weight: 40g / 1.4oz 22. Package size: 17 * 13 * 4.5cm / 6.7 * 5 * 1.8in 23. Package weight: 205g / 7oz Package Included: 1 X A5 Head Up Display 1 X Car Charge Cable 1 X Reflective Film 1 X Antiskid Pad 1 X User Manual

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface Description: Plug and play. HUD can auto adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System). HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water temperature,etc. Diversiform display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. Free switch. Km and mile can be switched freely to meet the need of inch auto meter. Suitable size. The display area is 5.5 inches which is very clear for driver to read data. Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer. Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment. Specification: 1.Service conditions: Environment temperature: -400C—+800C Barometric press: 86—106 KPa Relative humidity: 10%—95% Environment voice: 2.Alarm of sound level:> =30dB(A) 3.Work voltage: 9V~16Vdc(12Vdc/400mA) 4.Size of product: 14x85x147 (mm) 5.Weight of product: 320g Package Included: 1 X W02 HUD Host 1 X OBD Line 1 X Reflective Film 1 X User Manual 1 X Non-slip Mat W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface

W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface Package weight: 0.27 kg W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface Description: Plug and play. HUD can auto adapt to vehicle type which in line with OBDII or EUOBD(On-Board Diagnostic System). HUD can display many parameters at the same time as follows, vehicle speed, engine speed, water temperature,etc. Diversiform display mode. Driver can chose normal display mode, high- speed display mode and automatic display mode. Free switch. Km and mile can be switched freely to meet the need of inch auto meter. Suitable size. The display area is 5.5 inches which is very clear for driver to read data. Automatic power on and off. Starting with the vehicle starting, stopping with the vehicle stopping to protect the vehicle’s battery. Flexible alarm mode. HUD can offer single-stage and four-stage overspeed alarm modes to choose to make driving safer. Engine speed alarm. It contributes to shift gear in time to save fuel also has significance to new driver. The brightness can be adjusted automatically or manually to reach the best state which is in harmony with the environment. Specification: 1.Service conditions: Environment temperature: -400C—+800C Barometric press: 86—106 KPa Relative humidity: 10%—95% Environment voice: 2.Alarm of sound level:> =30dB(A) 3.Work voltage: 9V~16Vdc(12Vdc/400mA) 4.Size of product: 14x85x147 (mm) 5.Weight of product: 320g Package Included: 1 X W02 HUD Host 1 X OBD Line 1 X Reflective Film 1 X User Manual 1 X Non-slip Mat Click here for more deals W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface W02 Car HUD Head Up Display 5.5inch 12V Working Voltage With OBDII Interface

M6 Car HUD Head Up Display OBD2 EUOBD Car Driving Data Speed RPM Water Temperature Feature: 1. Available for cars with OBDII and EUOBD port(Car automatic diagnosis system), plug and play. 2. 3 inch HD screen display. 3. Multi-color design makes the screen more easier to read. 4. Nano-technology eliminates double reflections to be more clear. 5. Display rich contents: speed, rpm, water temperature, voltage, low voltage alarm, high water temperature alarm, over speed alarm. Freely switch between kilometers & miles. 6. Auto power on/off: HUD start up and off with vehicle started and shutdown, a effective protection of the car battery. Also retaining the manual switch mode, more easy to control HUD. 7. Automatic and manual brightness adjustment mode, driving without glare. Specification: Environment temperature -40c- + 80c atmospheric pressure 86-106KPa Relative Humidity 10% -95% environmental noise Alarm sound level "= 30dB (A) Working voltage 9V ~ 16Vdc (12Vdc / 400mA) Size 9*5.4*1.2(cm) Weight 40g Package Included: 1 X M6 Hud

AUTOOL X100S Universal Car HUD GPS Speedometer Head UP Digital Display Package weight: 0.40 kg Feature: 1. Display head-up-Dislay vehicle speed; Stand-alone full-size display. 2. Compatible with All Cars & Trucks. Use GPS Guided Signal, No Wiring Required for VSS (Vehicle Speed ￢ﾀﾋ￢ﾀﾋSignal). 3. Easy Installation-Direct Play-No professional installation is required. 4. the driving time and distance calculation and display 5. DisplayMPHOuKM / h-Simple push button set up. 6. Vehicle Driving Speed ￢ﾀﾋ￢ﾀﾋIndication, High brightness LED display speed, Easy on your eye. 7. Speed ￢ﾀﾋ￢ﾀﾋExcess Warning - Alarm Mute Function. over-speed alert: a 3 second audible alarm and keep the flash exposure will keep warning driver. 3 beeps for alert speeding. 8. Sleep automatic mode. Specification: Screen: 4.3 inch composite display Working temperature: -10￢ﾄﾃ-55￢ﾄﾃ Memory: 32K Size: 135*105*45mm Package Included: 1 X Car HUD GPS Speedometer Click here for more deals AUTOOL X100S Universal Car HUD GPS Speedometer Head UP Digital Display AUTOOL X100S Universal Car HUD GPS Speedometer Head UP Digital Display

!!!!!!!!!!!!! FREE SHIPPING !!!!!!!!!!!!!! on all orders over R300.00   Brand Name: Onever Size Name: 16*9.5*2cm / 6.3*3.7*0.8" (L*W*H) Type: Car HUD Projector Holder Material: ABS, silicon, PMMA Item Color: Black Golden Pink Applicable Device: Most phones and head up display within 6 inch Net Weight: 0.145kg / 5.1oz Feature1: Car HUD Projector Feature2: Phone GPS Navigation Holder Feature3: Phone GPS Navigation Projector Feature4: Car GPS Reflection Projector Feature5: car styling   click here to view all items  

Buy Kingneed C60S 3inch Car HUD Head-up Display Car Universal GPS Satellite Speedometer Speedi...(Black) for R669.00