Dual h bridge motor

Description Overview This driver uses Infineon chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A. Specifications Double BTS7960 large current (43 A) H bridge driver 5V Isolate with MCU, and effectively protect MCU 5V Power Indicator on Board Voltage Indication of Motor Driver Output end Can Solder Heat Sink Just need four lines from MCU to driver module (GND. 5V. PWM1. PWM2) Size: 4 x 5 x 1.2 cm; Able to reverse the motor forward, two PWM input frequency up to 25kHZ Two heat flow passing through an error signal output Isolated chip 5V power supply (can be shared with the MCU 5V), can also use the on-board 5V supply The supply voltage 5.5V to 27V Maximum Current: 43A Input level: 3.3V-5V More Products View More Products

10 Pcs L298N Dual H Bridge Stepper Motor Driver Board For Arduino DC Drive Controller Board  is available now from our  US  and  EU  warehouse   Excelent shipping to US and UK in  3-6  business days ship to Canada, Brazil in  7-10  days in US warehouse ship to European countries in  7-10  days in UK warehouse Description:   Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A (MAX single bridge) Storage temperature: -20 to +135 Max power: 25W Weight: 30g Size: 43 x 43 x 27mm   Note:   This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply, DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN$ control OUT3 OUT4   Note:  Package is not included the screws.   Package included:   10 x L298N Dual H Bridge Stepper Motor Driver Board For Arduino

DC Drive Controller Board is available now from our US and UK warehouse Excelent shipping to US and UK in 3-6 business days ship to Canada, Brazil in 7-10 days in US warehouse ship to European countries in 7-10 days in UK warehouse Description: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A (MAX single bridge) Storage temperature: -20 to +135 Max power: 25W Weight: 30g Size: 43 x 43 x 27mm Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply, DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN$ control OUT3 OUT4 Note:  Package is not included the screws. Package included: 1 x 236 L298N Dual H Bridge DC Stepper Motor Drive Controller Board Module arduino  

Description: Double H bridge drive Chip: L298N (ST NEW) Logical voltage: 5V Drive voltage: 5V-35V Logical current: 0mA-36mA Drive current: 2A (MAX single bridge) Storage temperature: -20 to +135 Max power: 25W Weight: 30g Size: 43 x 43 x 27mm Note: This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply, DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available. When ENA enable IN1 IN2 control OUT1 OUT2 When ENB enable IN3 IN4 control OUT3 OUT4 Note: Package is not included the screws. Package included: 1 x 236 L298N Dual H Bridge DC Stepper Motor Drive Controller Board Module arduino

Buy L298N Dual H Bridge DC Stepper Motor Drive transistor for R69.00

Buy 10 Pcs Geekcreit L298N Dual H Bridge Stepper Motor Driver Board... for R549.00

Buy H Bridge Remote Control 5A 3V-14V Dual DC Motor Drive Module Voltage Reverse PWM Speed Regulation Do for R120.00

Buy DC 5-12V 30A PWM Dual Channel Motor Control Module H Bridge Motor Drive Controller Board DHB-1A Reve for R532.00

Buy 3pcs H Bridge Remote Control 5A 3V-14V Dual DC Motor Drive Module Voltage Rever for R449.18

DC MOTOR DRIVER; BB-L298 is dual full bridge driver with up to 2.5A and 7-40V.

Description: There are two L9110S motor control chip onboard This module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motor Feature: Work under low static current Power supply voltage: DC 2.5V - 12V Each channel has 800mA continuous current output Low saturation pressure drop TTL / CMOS output level compatible, can be connected directly to the CPU Output built-in clamping diode, apply to the perceptual load Control and drive integrate in IC Pin high pressure protection function Working temperature: 0°C - 80°C Size: 29 x 21mm(L x W) Circuit diagram: Package included: 1 x L9110S stepper motor driver

Description:   1. Use of professional motor driver chip, built-in low conduction internal resistance MOS switch tube, extremely small heat, no heat sink, small size, power saving, is your battery power ideal choice. 2. Double Road 2.5A*2, is 1.5A motor driven version of the enhancement, built-in overheating protection circuit, do not fear the motor plug burned, the temperature drop automatically restored. (current smart cars on the market, voltage and current are within this range) 3. small size, light weight, 0 standby current INx MCU, IO or other signal source, MOTOR-A and MOTOR-B terminals connected to the motor. DC motor drive logic truth table: Parameter:   1. double H bridge motor drive, can drive two DC motor or 1 4 wire two phase stepper motor; 2. module supply voltage 2V-10V; 3. signal terminal input voltage 1.8-7V; 4. single line operating current 2.5A, low standby current (less than 0.1uA); 5. built-in anti common conduction circuit, when the input is suspended, the motor will not malfunction; 6. built in overheating protection circuit with hysteresis effect (TSD), no need to worry about motor blocking; 7. product size: 31*32*5mm (length, width, height), ultra small volume, suitable for assembly and vehicle; 8. mounting hole diameter: 2 mm.   Attention:   1. the power supply positive and negative connection will certainly cause damage to the circuit. 2. output on the short circuit or output short-circuit, and motor stall conditions, the chip will heat protection, but in the near or above the 10V voltage and peak current greatly exceed the 2.5A case will cause chip burn. Package included: 1 x 2.5A Dual Motor Drive Module

Buy 3pcs Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper M for R167.89

Buy 20pcs Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper for R656.82

Buy DC 3-36V 15A Peak 30A PWM DC Dual Channel Motor Driver Board High Power H Bridge Control Module for R570.00

Buy DC 3-36V 15A Peak 30A PWM DC Dual Channel Motor Driver Board Industrial Grade High Power H Bridge Co for R554.00

Buy L293D WiFi Smart Robot Car Motor Driver Expansion Board Dual High Power H Bridge Based On ESP12E SKU for R247.00

ESP8266 WiFi Motor Drive Expansion Board For NodeMCU ESP-12E This board just for >>>> SKU256450 Feature: Power input: Motor power supply (VM): 4.5V ~ 36V, can be powered separately Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and control Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H) Drive part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ?? Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V Working temperature: -25 ??~ + 125 ??/div> Drive Type: Dual high-power H-bridge driver ESP12E Dev Kit Control Port: D1, D3 (A motor); D2, D4 (B motor) Expand two-way motor-driven, two-way direct drive motor Onboard power switch Motor power, control power separation; In the experiment, by short-circuiting block the merger, the VIN and VM short, while power to the motor and the control board Notice: When inserted into the ESP-12E module, please note the direction consistent with an expansion board antenna The use of short modules that can simultaneously control board and motor. Package included: 1 x ESP8266 WiFi Motor Drive Expansion Board

Feature: Power input: Motor power supply (VM): 4.5V ~ 36V, can be powered separately Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately Module provides short-circuit sub (short the VM and VIN), you can easily use one power (must 4.5V ~ 9V) while completing motor drive and control Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H) Drive part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ?? Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V Working temperature: -25 ??~ + 125 ??/span> Drive Type: Dual high-power H-bridge driver ESP12E Dev Kit Control Port: D1, D3 (A motor); D2, D4 (B motor) Expand two-way motor-driven, two-way direct drive motor Onboard power switch Motor power, control power separation; In the experiment, by short-circuiting block the merger, the VIN and VM short, while power to the motor and the control board This board just for SKU256450. Notice: When inserted into the ESP-12E module, please note the direction consistent with an expansion board antenna The use of short modules that can simultaneously control board and motor. Package included: 3 x ESP8266 WiFi Motor Drive Expansion Board

Features: 1. Programmable and you can add functions. 2. TP4056 charger module to charge your Li-ion battery. 3. 18650 Li-ion battery solution power both L298N and UNO board. 4. Android bluetooth control, obstacle avoidance, IR remote control and line tracking/follower 4 functions in 1 smart robotic car. About the UNO: Add A6 and A7 analog I/O. Come with SHIELDED USB cable for stable data transit. Add two rows of the pass-thru holes for connecting normal dupont line. This UNO is manufactured using the Creative Commons files, compatible with Arduino software(IDE) in every way. Specifications: Material: Circuit Board + Electronic Component Finished Car Size: (L)X(W)X(H)21.6X12X13.5cm/8.50''X8.07''X5.31''(appr.) Package included: 1 x 4WD Acrylic Chassis Kit (4 Motors + 4 Wheels + 2 Acrylic body + 4 Encoder Disc + 1 Boat shape switch + 1 bag of screws and bolt) 1 x UNO R3 Board (Fully ARDUINO-Compatible) 1 x Shielded USB Cable 1 x V5 Sensor Shield 1 x L298N Dual H Bridge Motor Driver Module 1 x HC-06 Bluetooth Module 1 x IR Receive Module 1 x IR Remote Controller (Battery CR2032 included) 3 x Line Tracking Sensor Module 1 x HC-SR04 Ultrasonic Range Finder 1 x Acrylic Bracket for HC-SR04 Ultrasonic Range Finder 1 x SG90 Servo 1 x Acrylic Bracket for SG90 Servo 40 x Female to Female Dupont Cable 7 x Red Electronic Cable 5 x Black Electronic Cable 2 x TP4056 battery charging module (For charging one 18650 battery cell one time only) 3 x 18650 Battery Holder (2 in 1 type 1piece and single type 2pcs.18650 Battery NOT INCLUDED)

Description: There are some electronic modules,you will more interested during learning procedure. Provide learning lessons and technique support. You will know more about Arduino when you are assembling these modules. Android bluetooth control,obstacle avoidance,IR remote control and line tracking/follower 4 functions in 1 smart robotic car. 18650 Li-ion battery solution power both L298N and UNO board. TP4056 charger module to charge your Li-ion battery. Package included: 1 x 4WD Acrylic Chassis Kit (4 Motors + 4 Wheels + 2 Acrylic body + 4 Encoder Disc + 1 Boat shape switch + 1 bag of screws and bolt) 1 x UNO R3 Board (Fully ARDUINO-Compatible) 1 x 50cm Long Shielded USB Cable 1 x V5 Sensor Shield 1 x L298N Dual H Bridge Motor Driver Module 1 x HC-06 Bluetooth Module 1 x IR Receive Module 1 x IR Remote Controller 3 x Line Tracking Sensor Module 1 x HC-SR04 Ultrasonic Range Finder 1 x Acrylic Bracket for HC-SR04 Ultrasonic Range Finder 1 x SG90 Servo 1 x Acrylic Bracket for SG90 Servo 40 x Female to Female Dupont Cable 7 x Red Electronic Cable. 5 x Black Electronic Cable. 2 x TP4056 Battery Charging Module (For charging one 18650 battery cell one time only) 3 x 18650 Battery Holder Here is the link of the (←click here) for your reference, you may download for yourself

Geekcreit™ DIY NodeMCU Lua 4WD Open Source ESP8266 ESP-12E WiFi Smart Car Kit Description: This WiFi RC smart car is designed and developed based on ESP-12E from ESP8266, which can be controlled by mobile, PC. Some useful download links: For NodeMcu Lua + WiFi Motor shield, please go to Product ID: 1021716 Motor DataSheet for Tank/Car Chassis: http://bbs.smartarduino.com/showthread.php?tid=2039 Chassis Installation http://bbs.smartarduino.com/forumdisplay.php?fid=21 Software manumal http://bbs.smartarduino.com/showthread.php?tid=2036 Android App http://bbs.smartarduino.com/showthread.php?tid=1978 iOS App http://bbs.smartarduino.com/showthread.php?tid=2037 FirmWare http://bbs.smartarduino.com/showthread.php?tid=2013 Motor shield http://bbs.smartarduino.com/showthread.php?tid=6 NodeMCU http://bbs.smartarduino.com/forumdisplay.php?fid=2 Features: Color: Red, Blue, Green, Black, Transparent (Optional) Motor power supply (VM): 4.5V ~ 36V, can be a separate power supply; Control power (VIN): 4.5V ~ 9V (10VMAX), can be powered separately; Module provides short-circuit sub (short the VM and VIN), you can easily use one power (which must be 4.5V ~ 9V) simultaneously drive and control the motor; Logic Operating current Iss: ≤60mA (Vi = L), ≤22mA (Vi = H); Working current driving portion Io: ≤1.2A; Maximum power dissipation: 4W (T = 90 ?? Control signal input level: High: 2.3V≤VIH≤VIN; Low: -0.3V≤VIL≤1.5V Working temperature: -25 ??~ + 125 ??/span> Drive Type: Dual high-power H-bridge driver Support wireless 802.11 b / g / n standards; Support STA / AP / STA + AP three operating modes; Built-in TCP / IP protocol stack to support multiple TCP Client connection (5 MAX); D0 ~ D8, SD1 ~ SD3: used as GPIO, PWM, IIC, etc., port driver capability 15mA; AD0: 1 Road ADC; Current: continuous transmission: ≈70mA (200mA MAX), Standby: Transfer rate: 110-460800bps; Support UART / GPIO data communication interface; Remote firmware upgrade (OTA); Smart Link supports intelligent networking capabilities. Car battery: 4 x AA batteries, batteries not included!! (Battery Case not included) Package included: 1 x car chassis 1 x ESP-12E motor shield 1 x NodeMCU development board