Beidou gps module

Product Introduction: 1.Support BDS/GPS single system,support QZSS and SBAS system 2.Support A-GNSS 3.Cold Boot Acquisition Sensitivity:-148dBm 4.Tracking Sensitivity:-162dBm 5.Positioning Precision:2.5m (CEP50) 6.First Time Positioning Time:32s 7.Low Power Consumption:continuous operating 8.Built-In Antenna Detection And Antenna Short Circuit Protection Pin Definition: 1.VCC: power (3.3-5.0V) 2.GND: ground 3.TXD: module serial port transmit pin (TTL level, it cannot directly connect RS232 level), it can connect MCU RXD 4.RXD: module serial port receive pin (TTL level, it cannot directly connect RS232 level), it can connect MCU TXD 5.PPS: clock pulse output pin Package included: 1 x Beidou GPS Module 1 x antenna

Buy Beidou GPS Module Locator BDS Satellite Positioning Navigator Compass Module Dual Mode for R376.90

Buy GPS Active Ceramic Antenna IPX IPEX Interface For GPS Module for R207.67

Description: Antenna size: 20 * 4 * 6mm(L*W*H) Line length: 2.5cm Center frequency: GPS antenna (GPS-1575MHz) Package included: 1 x GPS Active Ceramic Antenna

Buy BG01 GPS Module GPS+BDS Beidou Dual-mode Satellite Positioning and Navigati for R269.00

Buy BN-200 Small Size M8030 Chipset GPS Module Antenna GPS GLONASS Dual GNSS Module for R415.15

Features: This product is suitable for aircraft positioning, flight route, and automatic return flight. The built-in compass can effectively reduce the interference to the magnetic field sensor. Ublox NEO M8N is greatly upgraded on the basis of 6M, low power consumption, high precision, support GPS+GLONASS dual positioning system, improve the search speed and search star number, effectively reducing the HDOP value. Package included: 1 x APM2.6 2.8 GPS Module High Precision Ublox NEO-M8N GPS With Electronic Compass PIXHAWK

Description: M5Stack GPS Module M8N With Internal & External Antenna MCX Interface IoT Development Board Built-in M8N GPIO16-TXD GPIO17-RXD GPIO34-PPS Package included: 1 x M5Stack GPS Module Kits

Features: This module is suitable for aircraft positioning, flight route, and automatic return flight. The built-in compass can effectively reduce the interference to the magnetic field sensor. Ublox 6M has a strong cost-effective, entry-level players preferred. Package included: 1 x APM2.6 2.8 APM2.5 GPS Module Ublox NEO-6M With Electronic Compass Pixhawk

Buy GY GPS Module Board 9600 Baud Rate With Antenna for R215.00

Buy GY GPS Module Board 9600 Baud Rate With Antenna for R300.07

Buy VK2828U7G5LF GPS Module With Antenna TTL Level 1-10Hz With Flash Flight Control for R349.00

GPS Shield GPS Record Module With SD Interface For Arduino Introduce: The expansion board is specifically designed for the Arduino UNO and other GPS record expansion board. Provides two kinds of GPS antenna interface. Supports 3.3V and 5V two voltage levels of operating base (such as leaf maple), IO port interface leads with multiple analog pins can be directly connected to the electronic building blocks for rapid prototyping. With SD card slot, support for GPS information record. Can be used with FT232RL module, directly connected the FT232RL module's TX, RX, VCC, GND to GPS corresponding feet, through the serial debugging software to view the data. Feature: Provides 3.3V and 5V operation level select, so it can be compatible with more baseboard, such as 3.3V ChipKit UNO32, leaf maple and other platforms, compatibility stronger. Use active GPS antenna. With micro SD interface. Can be set via jumpers connected to TxD and RxD you need Ardino pins (D0-D8 optional), it is more stronger expansibility than directly connect D0D1. Provides multiple electronic building blocks interface to facilitate quick access various types of electronic building block modules, the Add button, LED display or a relay switch function. TF deck, SPI interface. Support Arduino library. With reset button, you can direct reset Arduino backplane. What INT1 INT0 is? If you use a jumper connected to ON, then the two trigger signals from the GPS module (such as every second clock signal, each output prompt signal information) pin is connected to the Arduino interrupt pins, you can use these trigger an interrupt to do the setting you need- Default is off. Description: Board size: 56 x 54mm Weight: About 45g Operation temperature: -40°C to +85°C Package included: 1 x GPS shield with antenna

Description:   GPS module Minimum size: 23 * 17mm Dual GPS Antenna Interface: SMA / IPEX With rechargeable Electronics: accelerates startup With EEPROM: change the baud rate and other data can be saved without power GPS serial output of raw data, which can be accessed 5V / 3.3V single-chip serial resolve   Package Included:   1 x GPS Mini NEO-7N Satellite Positioning Module For C51 Arduino STM32

Emlid Reach RS2 GPS complete set. Hard carry case and bi-pod included. Rugged Blackview controller with Landstar 7 field software. NTRIP support. 16 GB internal storage. UHF LoRa Radio covers up to 8km from base station. Sim card, wifi, bluetooth. For Land and Engineering Surveyors GPS/QZSS L1C/A, L2C, GLONASS L1OF, L2OF, BeiDou B1I, B2I, Galileo E1-B/C, E5b. Almost new, in use for one year only. Reason for selling: Owner emigrating.