Gps serial module

Buy GPS Serial Module APM2.5 Flight Control GT-U7 with Ceramic Antenna for DIY Handheld Positioning for R285.23

GPS Shield GPS Record Module With SD Interface For Arduino Introduce: The expansion board is specifically designed for the Arduino UNO and other GPS record expansion board. Provides two kinds of GPS antenna interface. Supports 3.3V and 5V two voltage levels of operating base (such as leaf maple), IO port interface leads with multiple analog pins can be directly connected to the electronic building blocks for rapid prototyping. With SD card slot, support for GPS information record. Can be used with FT232RL module, directly connected the FT232RL module's TX, RX, VCC, GND to GPS corresponding feet, through the serial debugging software to view the data. Feature: Provides 3.3V and 5V operation level select, so it can be compatible with more baseboard, such as 3.3V ChipKit UNO32, leaf maple and other platforms, compatibility stronger. Use active GPS antenna. With micro SD interface. Can be set via jumpers connected to TxD and RxD you need Ardino pins (D0-D8 optional), it is more stronger expansibility than directly connect D0D1. Provides multiple electronic building blocks interface to facilitate quick access various types of electronic building block modules, the Add button, LED display or a relay switch function. TF deck, SPI interface. Support Arduino library. With reset button, you can direct reset Arduino backplane. What INT1 INT0 is? If you use a jumper connected to ON, then the two trigger signals from the GPS module (such as every second clock signal, each output prompt signal information) pin is connected to the Arduino interrupt pins, you can use these trigger an interrupt to do the setting you need- Default is off. Description: Board size: 56 x 54mm Weight: About 45g Operation temperature: -40°C to +85°C Package included: 1 x GPS shield with antenna

Overview: Optical isolation USB to TTL Serial Module Equipped with CH340T USB to serial chip, achieved the power and TTL signal isolation, High-speed and stability, it could  avoid the damage of USB and computer blue screen or other issues while use the USB to TTL serial port module, due to improper operation or other external impact on the computer  , could improve the safety of debugging. The function and characteristics: 1. Onboard 500mA self-recovery fuse and 5V isolated power supply module to protect the computer from damage 2. Onboard stable CH340T USB to serial chip 3. Serial TTL level through the optocoupler isolation, fast (up to 921600bps), high reliability 4. Output TX RX end with protection diode function, can improve the impact resistance 5. Computer USB end and serial port output end realize complete electrical isolation 6. Output TTL level can be set to 3.3V / 5V 7. Serial output maximum output current of 150mA 8. The board size: 55x26mm Feature: - 3.3V, 5V: Output supply voltage and TTL level switching pin - VCC, GND: Power supply output pin - The TX, RX, GND and VCC pins of the serial port module are connected to the RX, TX, GND, and VCC pins of the user equipment. When the isolated serial port module VCC pin with a jumper cap 5V, the output 5V TTL level and power supply voltage; while VCC pin with 3.3V jumper cap, the output level of 3.3V TTL and power supply voltage. The following is an example of using the isolated serial interface module to debug the 3.3V ESP8266 module (With the jumper cap to isolate the serial port module VCC and 3.3V shorted, isolated serial port module TX, RX, GND, VCC respectively ESP8266 RX, TX, GND, VCC), as the picture shows: The background description of using Isolated serial port module: USB interface was already one of the interfaces that most commonly used by engineers to debug product development. USB interfaces are not only often used in contact with the human body, but also in many cases, it also supplies power to external devices. Strong external power, strong interference may cause damage to the computer USB port or motherboard, then electrical isolation becomes particularly important. LC optically isolated USB to TTL serial port module is suitable for the following occasions: 1. Electrical equipment which containing strong electricity USB devices with high power (such as high voltage, inverter, motor drive, etc.) connact to computer USB may burn out the USB interface, be sure to isolate to ensure that the computer USB port, motherboard and personal safety, can effectively avoid USB Mouth damage and personal injury. 2. Electrical equipment with Strong interference  Such as motor drives, inverters and other great interference itself, into the USB port may lead to computer crashes, blue screen, no response. You can isolate the USB interface through this device to avoid interference with the computer. 3. Noise-sensitive equipment The computer itself is a noise source, through the isolated USB port, you can avoid high-frequency interference to the computer transmission to sensitive devices, and thus better access to data, such as audio equipment, precision measuring equipment and medical equipment.  4. Ordinary electronic equipment For ordinary electronic equipment, through the isolation can effectively avoid operational errors caused by short-circuit damage to the computer USB port, blue screen and other issues, greatly improving the security of the operation. P.S: As there is a certain error of the isolated serial module 5V to 5V above the isolated power supply, so when the VCC through the jumper cap 5V pin and no load when the output power supply voltage will be about 5.4V, but do not worry, when connected to the user equipment, After the device output voltage will automatically drop to 5V or so. Package included: 1 x  High-speed Isolation USB To TTL Serial Module

5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

3Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 3 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

5pcs HC-05 Wireless Bluetooth Serial Module With Baseplate For Arduino Note: This module does not suitable for IOS system. Pin serial port descriptions: PIO8 connect LED, indicates the status of working, after powered the module flashing, different states in different flashing intervals. PIO9 connect LED, indicates successful connecting module, after successful mating bluetooth serial port, LED long lights. PIO11 state switch pin (high level) -> AT command response to the work state, low level or dangling -> Bluetooth regular work status. On module with a reset circuit, re-power to complete the reset. Main module setup steps: 1. PIO11 set high. 2. Power ON, the module into the AT command response status. 3. HyperTerminal or other serial tool, set the baud rate 38400, 8 data bits, 1 stop bit, no parity, no flow control. 4. Serial send characters "AT + ROLE = 1 r n", successful return "OK r n", which r n for carriage return. 5. PIO set low, re-power, module as the main module, automatic search from module to establish a connection. Feature: 6V - 4.5V power supply; Support connect Android phones with Bluetooth; The default baud rate: 9600 can be modified according to the data sheet; Package included: 5 x HC-05 Wireless Bluetooth Serial Module

Description: 232 level output, 9600, 1HZ output, standard NMEA-0183 protocol output. Parameter Description Chip characteristics Chip U-blox U7 Receiving mode GPS, QZSS, WAAS, SBAS, EGNOS, MSAS Frequency GPSL1, SBAS L1 Channel 56 search channels Sensitivity Track -162dBm Recapture -160dBm Cold start -148dBm Precision Horizontal accuracy 2.0 m CEP 2D RMS SBAS assist (open space) Speed accuracy 0.1m/s 95% (SA off) Time accuracy 1us Start Time Cold start 29s Warm start 25s Hot Start 1s Output Data Baud rate 4800bps-921600bps,default 9600bps Output level TTL or RS232, default RS-232 level Output protocol Default NMEA-0183 protocol Standard GNSS 1Hz-10Hz, default 1Hz Work limit Height 50,000m maximum Speed 515m/s maximum Gravity acceleration 4g maximum Power consumption Voltage DC 3.6V-5.5V, typical: 5.0V Current Normal 45mA@5.0V Physical parameter Size 28mm*28mm*8mm Weight 11.5 grams Line length 2m Connector 1.25 pitch 6pin socket Surroundings Operating temperature -40 °C ~ +85 °C storage temperature -40°C ~ +85°C Indicator light TX light Power-on blue light flashes to indicate that there is data output. PPS light The light is not lit when it is not positioned. After 3D positioning, it starts to blink. The pins of the module are: 1.PPS, there is a second pulse output after positioning, the pulse period is 1s, and the high level lasts for 100ms, which is used for system synchronization. 2. GND, ground. 3.TX, the data output of the module. 4.RX, the data input of the module. 5.VCC, 3.6-5.5V, recommended 5.0V. 6. BOOT, please hang out during normal work. Package included: 1 x Beitian BS-280 232 GPS Receiver Module 1 x cable

Description: 232 level output, 9600, 1HZ output, standard NMEA-0183 protocol output. Parameter Description Chip characteristics Chip U-blox U7 Receiving mode GPS, QZSS, WAAS, SBAS, EGNOS, MSAS Frequency GPSL1, SBAS L1 Channel 56 search channels Sensitivity Track -162dBm Recapture -160dBm Cold start -148dBm Precision Horizontal accuracy 2.0 m CEP 2D RMS SBAS assist (open space) Speed accuracy 0.1m/s 95% (SA off) Time accuracy 1us Start Time Cold start 29s Warm start 25s Hot Start 1s Output Data Baud rate 4800bps-921600bps,default 9600bps Output level TTL or RS232, default RS-232 level Output protocol Default NMEA-0183 protocol Standard GNSS 1Hz-10Hz, default 1Hz Work limit Height 50,000m maximum Speed 515m/s maximum Gravity acceleration 4g maximum Power consumption Voltage DC 3.6V-5.5V, typical: 5.0V Current Normal 45mA@5.0V Physical parameter Size 28mm*28mm*8mm Weight 11.5 grams Line length 2m Connector 1.25 pitch 6pin socket Surroundings Operating temperature -40 °C ~ +85 °C storage temperature -40°C ~ +85°C Indicator light TX light Power-on blue light flashes to indicate that there is data output. PPS light The light is not lit when it is not positioned. After 3D positioning, it starts to blink. The pins of the module are: 1.PPS, there is a second pulse output after positioning, the pulse period is 1s, and the high level lasts for 100ms, which is used for system synchronization. 2. GND, ground. 3.TX, the data output of the module. 4.RX, the data input of the module. 5.VCC, 3.6-5.5V, recommended 5.0V. 6. BOOT, please hang out during normal work. Package included: 5 x Beitian BS-280 232 GPS Receiver Module 5 x cable

VK-162 Notebook Usb GPS Navigation Module Support Google Earth Description: VK-162, is a complete GPS receiver. Built-in satellite receiver antenna, satellite receiver core using the most advanced core UBLOX positioned to provide highly accurate positioning information, it is also able to meet the stringent requirements of industrial positioning and personal use as needed. Scope from the car navigation, security systems, map making and survey to agricultural uses. Built-in button-type battery for storing satellite data such as satellite signal status, location and time of the last previously used to increase the positioning speed boot time. Built-in WAAS / EGNOS demodulator without additional hardware can receive WAAS / EGNOS signals. Support NMEA0183 3.01 version of the output data format. Feature: Electrical properties of the interface: Wide voltage range: the main power supply is + 3 3 V ~ + 5 V Operating temperature: - 4 0 ??t o + 8 5 ??br /> C / A code, 1.023 MHz band receiving stream: L1 [575.42MHz] Receive Channel: 56CH Positioning performance Rate: Direction: Timing accuracy: 30ns Reference coordinate system: WGS-84 The maximum height of altitude: 50,000 m Maximum speed: 500 m / s Acceleration: Package included: 1 x VK-162 Notebook Usb GPS Navigation Module Support Google Earth

5PCS Beitian BS-280 232 GPS Receiver Module 1PPS Timing With Flash + GPS Antenna Package contains 1 X item of the smallest listed variant.

Buy Geekcreit HC-12 433MHz SI4463 Wireless Serial Module Wireless Transceiver Transmission Serial for R210.00

Buy Beitian BS-280 232 GPS Receiver Module 1PPS Timing With Flash + GPS Antenna for R349.43

Buy 3Pcs Beitian BS-280 232 GPS Receiver Module 1PPS Timing With Flash + GPS Antenna for R898.00

Buy Geekcreit HC-12 433MHz SI4463 Wireless Serial Module Wireless Transceiver Transmission Serial Comm for R243.16

3Pcs CJMCU CP2102 USB To TTL/Serial Module Downloader For Arduino