68mm diamond core

Ø20mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45¿¿ angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED ¿¿5.0mm 800 rpm ¿¿6.0mm 600 rpm ¿¿7.0mm 500 rpm ¿¿8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm   IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.  

Buy Diamond Core Drill Bit Hole Puncher For Air-conditioner Range Hood Dia. 20/30/40/51/63... (SIZE: #5) for R1,157.89

Buy DIAMOND CORE BIT 152MM X 450MM X 1 1/4 CONCRETE MASTER DBK for R5,709.58

Buy Diamond Core Bit 102Mm X 450Mm X 1 1/4 Concrete Master Dbk for R3,217.00

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø12.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø16mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø8mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø38mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø19mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø14mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø30mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill"s chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø6mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø20mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø10.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.

Ø10mm Diamond core bit Application: The diamond core bit is used to drill holes in: Ceramic tiles Marble Grade 5 porcelain (hardest) Granite Glass Slate The diamond core cuts faster, smoother and lasts longer than any other core drills. How to use the diamond core bit: The diamond core drill bit must be used with water at all times when drilling. The water serves as a coolant to prevent the diamonds from overheating. The maximum allowable temperature for a diamond core bit is 500°C. There is no pilot drill with the diamond core bit. A low rpm rotary drill with a planetary gearbox is required to be used with a diamond core bit. It is possible to use a cordless drill, but in the lowest gear setting. No hammer action is used. Tightly fasten the diamond core bit in the drill's chuck. Keep the bit steady at a 45° angle with the starting point on the edge of the assigned area to be drilled whilst the bit is rotating. A notch will be made (this is normal). Gradually move the drill from 45° to 90° and continue drilling until finished. Allow the diamond core bit to cool down completely before proceeding to drill another hole. Water can be applied by: spraying water on the surface, using a wet sponge, attaching a water feed device. This is necessary when drilling into a wall tile. Please have a look at the video in the tabs above showing how to use the diamond core bit. An indication of the correct spindle speed: DIAMOND CORE BIT DIAMETER SPINDLE SPEED Ø5.0mm 800 rpm Ø6.0mm 600 rpm Ø7.0mm 500 rpm Ø8.0mm 500 rpm Ø10.0mm 400 rpm More than Ø40.0mm (>10.0mm) less than 400 rpm IMPORTANT: The tool life will mostly depend on the proper usage and the hardness of the items drilled into. It is normal for a diamond core bit to last up to 10 or more drilled holes in hard tiles. Please remember to always use water when drilling with diamond core bits.