5pcs geekcreit

5Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Package contains 1 X item of the smallest listed variant.

5Pcs Geekcreit MB-102 MB102 Solderless Breadboard + Power Supply + Jumper Cable Kits For Arduino Package contains 1 X item of the smallest listed variant.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Instructions: 1. Clear: Press and hold the learning button for about 3 seconds, the LED will go out, flash 3 times after a while, clear OK. 2, learning the code: press the learning button, the LED lights up, release the learning button, enter the learning mode, press any button of the remote control at this time, transmit the signal, when you see the LED on the receiving module flashes 3 times, that is Indicates that the learning pair code is OK. 3. The remote control after learning can be controlled. Specifications: Working Temperature: -25~75C Frequency band: +-0.2MHz ReceiveDistance: 20-100M (open space) Receive Sensitivity: -108dB Working Frequency: 433MHz(Others can be customized) Quiescent Current: Working Voltage: DC3.3~5V Working mode:Point move, self-locking, interlocking Pin: GND: groud or negative pole +V: DC3.3~5V input D0: Data output D1: Data output D2: Data output D3: Data output VT: Output Precautions: 1. Do not operate with power. Turn off the power and operate it. After the test is confirmed, the power is turned on. 2. When using wireless electronic products, care should be taken to avoid strong interference sources such as metal masks, large electronic devices, and electromagnetic fields to prevent the modules from working properly. 3. Do not use this electronic product abnormally. Abnormal use will reduce product performance and longevity. In severe cases, damage to the product will also pose a safety hazard. Package Included: 5 x RX480E-4 433MHz Wireless RF Receiver 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output 5pcs Geekcreit RX480E-4 433MHz Wireless RF Receiver Learning Code Decoder Module 4 Channel Output

Buy 5pcs Geekcreit D1 Mini Single Lithium Battery Charging And Battery Boost Shield for R317.86

Buy 5Pcs Geekcreit HC-12 433MHz SI4438 Wireless Serial Module Wireless Transceiver for R776.08

Buy 5pcs Geekcreit USB Boost Module 5V to 9V12V Step Up Module Adjustable Voltage Current Display for R1,053.80

Buy 5pcs Geekcreit 3 in 1 AC 60-500V 100A Voltmeter Ammeter HZ Hertz Frequency Mete for R599.27

Buy 5Pcs Geekcreit ESP-F ESP8266 Remote Serial Port WiFi IoT Module Nodemcu LUA RC Authenticity for R375.14

Buy 5Pcs Geekcreit D1 Mini V2.3.0 WIFI Internet Of Things Development Board Based ESP8266 for R403.12

Buy 5Pcs Geekcreit DC 0-200V 0.36 Inch Mini Digital Volt Meter Voltage Tester 3 Wir for R253.87

Buy 5Pcs Geekcreit 10 Value Electronic Components Storage Assortment Box for R184.57

Buy 5Pcs Geekcreit IIC / I2C 1602 Blue Backlight LCD Display Screen Module For for R516.81

Buy 5pcs Geekcreit D1 Mini Single Lithium Battery Charging And Battery Boost Shield Board for R307.48

Buy 5pcs Geekcreit Blue 3D Mini SMD PCB Stereo Christmas Tree DIY Music Kit for R379.00

Buy 5pcs Geekcreit RX500A 315/433MHz High Sensitivity Superheterodyne Wireless Rece for R349.00

Buy 5Pcs Geekcreit MB-102 MB102 Solderless Breadboard + Power Supply + Jumper Cable for R732.64

Buy 5pcs Geekcreit Yellow 3D Mini SMD PCB Stereo Christmas Tree DIY Music Kit for R335.67

Buy 5Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch for R630.16

Buy 5pcs Geekcreit Yellow 3D Mini SMD PCB Stereo Christmas Tree DIY Music Kit for R366.28

Buy 5pcs Geekcreit W1209S DC 12V Mini Thermostat Regulator -50 to 120 Digital Temperature Controller for R341.49

Buy 5Pcs Geekcreit IIC / I2C 1602 Blue Backlight LCD Display Screen Module For for R516.79

Buy 5Pcs Geekcreit WS2812B RGB Shield Expansion Module For D1 Mini Development for R159.00

Buy 5Pcs Geekcreit 36 Value Electronic Components Storage Assortment Box for R985.07

Buy 5Pcs Geekcreit USB To RS485 TTL Serial Converter Adapter FTDI Interface FT2 for R489.00

Buy 5pcs Geekcreit 3 in 1 AC 60-500V 100A Square Yellow LED Digital Voltmeter Ammeter Hertz Meter Sig... for R494.35

Buy 5Pcs Geekcreit IR Infrared Obstacle Avoidance Sensor Module For Smart Car Rob for R119.76

Buy 5Pcs Geekcreit 328P Multifunction Expansion Board V3.0 For NANO UNO for R278.00

Buy 5pcs Geekcreit NodeMcu Lua ESP8266 ESP-12F WIFI Development Board for R842.44

Buy 5Pcs Geekcreit V2 ESP8266 Development Board or IOT NodeMcu ESP12E Lua L293D for R471.00

5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module