5pcs geekcreit dc 12v

5Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Package contains 1 X item of the smallest listed variant.

Buy 5Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch for R630.16

Buy 5Pcs Geekcreit DC 0-200V 0.36 Inch Mini Digital Volt Meter Voltage Tester 3 Wir for R253.87

Buy Geekcreit DC 12V 4CH Channel Wireless Remote Control Switch Learning Type Relay Control Module With for R355.00

Buy 5pcs 433MHz DC 12V One Key Gate RF Wireless Remote Control Garage Door Transmit for R449.00

Description: 1. The use of synchronous rectifier converter design, high efficiency, high current work doesn't require additional heat sink, the output is smooth DC (no pulse), direct drive output design. 2. Can support all 12V 5A within the fan, including brush DC motors, pumps, light bulbs, etc. Can't exceed the maximum current conditions can work more than one fan in parallel, a soft-start power. 3. Can be adjusted by rotating the board any manual speed control resistor. 4. With four-zone automatic temperature control variable speed function, plug in the temperature control probe automatically after the entry into force, temperature control will manually adjust the speed to the lowest speed, the highest speed is 12V through. The linear speed of the middle speed change. 5. With the work monitoring function of a channel, can support a way with a speed wire (such as three-wire fan) stop monitoring alarm, when the speed is less than 450 rpm sound and light alarm (need to be equipped with buzzer). Specifications: Working voltage: DC 12V Circuit load capacity: maximum current per output 5A, the bus current up 9A Output range: the first channel: 20%-100% or 40%-100% (TFL = ON); the second channel and the third channel: 10%-100%; (Note: above range only for PWM range, the actual control effect will vary depending on the fan) Temperature probe parameters: 50K B=3950 Thermostat temperature zone error: error depending on the temperature probe, generally 3%-5% Stall alarm minimum speed: 700-800 rpm Circuit board size: 50 x 49 x 15mm Center distance of locating hole: 44 x 43mm, diameter: 3.2mm Setting switch description: TFL(No.1): the lowest temperature channel PWM setting, when ON state FAN1 PWM minimum is 40%, when OFF the minimum PWM of FAN1 is 20%,. TP1 TP2(No. 2, 3): temperature channel control temperature zones are interpreted as follows(need to use with the temperature probe) TP1 TP2 Accelerating temperature Full speed temperature OFF OFF 35￢ﾄﾃ 45￢ﾄﾃ ON OFF 40￢ﾄﾃ 55￢ﾄﾃ OFF ON 50￢ﾄﾃ 70￢ﾄﾃ ON ON 60￢ﾄﾃ 90￢ﾄﾃ Package included: 5 x DC 12V 5A PWM fan speed controller 5 x Temperature probe 5 x Buzzer

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Swi for R369.00

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch for R415.57

Buy 3Pcs Geekcreit DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter With Rec for R416.00

5pcs PAM8610 Dual Channel DC 12V 15W x 2 Class D HD Digital Audio Stereo High Power Amplifier Board

5pcs 2 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A Package contains 1 X item of the smallest listed variant.

Buy 5pcs Geekcreit W1209S DC 12V Mini Thermostat Regulator -50 to 120 Digital Temperature Controller for R341.49

Specification: Supply voltage: DC 12V Static current: ≤35MA, attract current ≤65MA Output voltage: DC 12V Output power: 10A relay Measurement input: NTC (10K 0.5%) Waterproof Sensor Environmental requirements: -10 ~ 60℃, Humidity 20% ~ 85% Dimensions: 48 x 40mm Cable length: About 52 cm Temperature control mode: ON / OFF Temperature range: -50 ~ +110°C Control accuracy: 0.1°C Hysteresis  accuracy: 0.1°C Refresh rate: 0.5S High temperature protection: 0 ~ 110°C Resolution: When temperature is 0.1°C, the resolution is -9.9~99.9, other temperature segment is 1°C Package included: 5 x Digital temperature control switch with cable

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Specification: Input Power Supply: 12V DC Load Voltage: AC240V 2A Maximum operating current: 13.8mA Trigger mode: low level Input control signal voltage: (0-2.5V low state relay OFF) (3.3-5V state high relay ON) Blue KF301 terminal connection control line is more convenient. Module interface: DC +: positive power supply (by relay voltage power supply) DC-: connect power negative CH: Relay Module signal triggering end (Low level trigger effective) Note: Power must be DC voltage and need to be consistent with the voltage relay Package Included: 5 x Low Level Relay Module 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A

Buy Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control for R119.00