-
loading
Ads with pictures

5pcs 5v


Top sales list 5pcs 5v

South Africa (All cities)
5Pcs 5V Infrared Line Tracking Sensor Module For Arduino Feature: Quantity: 5pcs Size: 3.5 x 1cm Power supply: 5V DC Detector distance: 10mm Build-in Tcrt5000 Sensor NSOR Applicable to a variety of platforms including Arduino / AVR / ARM /PIC Package included: 5 x Tracking Sensor Module  
R 129
See product
South Africa (All cities)
5Pcs 5V MAX485 TTL To RS485 Converter Module Board For Arduino Feature: Operating voltage: 5V On-board MAX485 chip A low power consumption for the RS-485 communication Slew-rate limited transceiver 5.08mm pitch 2P terminal Convenient RS-485 communication wiring All pins of chip have been lead to can be controlled through the microcontroller Board size: 44 x 14mm Package included: 5 x MAX485 TTL to RS485 module
R 86
See product
South Africa (All cities)
5Pcs 5V To 3.3V DC-DC AMS1117 800MA Step-Down Power Supply Buck Module Features: Size: 8.6 x 12.33 mm Input voltage: DC 4.2 V - 10 V Output: 3.3 V, 800 mA Note: 1.Boost modules or buck module indicate the operating voltage, Please do not exceed operating voltage, or it will be damaged easily! 2.Boost module output voltage can only be greater than or equal to input voltage, cannot be less than the input voltage! 3.Buck module input voltage must be higher than output voltage of 1.5V or 2V, otherwise it can not output enough power! 4.Automatic Adjustable Boost or Buck module has start voltage and limit working voltage, Please do not exceed them, or it will be damaged easily! 5.Cannot reverse polarity, or it will be short circuit, or will be born easily! Package included: 5 x Step-down module
R 52
See product
South Africa (All cities)
5Pcs 5V 1-Channel H/L Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 5 x 1 Channel H/L trigger optocoupler relay module
R 138
See product
South Africa (All cities)
5Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module
R 410
See product
South Africa (All cities)
5Pcs 5V MAX485 TTL To RS485 Converter Module Board For Arduino
R 230
See product
South Africa (All cities)
FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 5 x 5V 1 channel relay module 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino
R 109
See product
South Africa (All cities)
Buy 5Pcs 5V Micro USB Tiny AVR ISP ATtiny44 USBTinyISP Programmer for R340.00
R 340
See product
South Africa (All cities)
Buy 5Pcs 5V MAX485 TTL To RS485 Converter Module Board for R210.00
R 210
See product
South Africa (All cities)
Buy 5pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with for R542.19
R 542
See product
South Africa (All cities)
Buy 5Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module for R219.85
R 219
See product
South Africa (All cities)
Buy 5pcs 5V 5A DC USB Buck Module USB Charging Step Down Power Board... for R489.00
R 489
See product
South Africa (All cities)
Buy 5pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with Shell for R746.00
R 746
See product
South Africa (All cities)
Buy 5pcs 5V 4 Channel Relay Module PIC ARM DSP AVR MSP430 Blue Geekcreit for Arduino - products that... for R399.00
R 399
See product
South Africa (All cities)
Buy 5Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module for R327.00
R 327
See product
South Africa (All cities)
Buy 5pcs 5V 2 Channel Relay Module Control Board With Optocoupler Protection for R235.00
R 235
See product
South Africa (All cities)
Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 5 x 5V 1 channel relay module
R 122
See product
South Africa (All cities)
Description: This Power Source For The Isolation Industrial-grade Built-in Power Supply Module, Temperature Protection, And Short Circuit Protection, AC85 - 265V Input Voltage, Wide 431 Precision Voltage Stability DC5V Output, With Mounting Holes, With Input And Output EMI Filter circuit Feature: Size: 5.1 x 2.4 x 2.0cm (L x W x H) Working Temperature: -20 - 60??/span> Relative Humidity: 40 - 90%RH Input Voltage Range: 85- 265V Input Current: 0.054A(AC110V) 0.027A(AC220V) Input Inrush Current: 20A Output Voltage Range: 4.80-5.2V 0-1000mA Output Power: 0 - 5.5 W Output Efficiency: 80% Input Voltage of AC 85 - 265v 50/60 HZ Output Voltage DC5V (±0.2V) Output Current 1000MA Power: 5W Note: The End of the Step Down Module Can Be Conductive, Do Not Touch The Bottom of Template when you Test or to Use, Need Mattress Insulator Pad, Clean Cardboard Conductive things, Avoid Power Board contact to conductive objects such as Wire, so as to Avoid Electric Shock And Burn Out The Power Supply Board Package included: 5 x 5V 1A AC-DC Power Supply Step Down Module Bare board
R 229
See product
South Africa (All cities)
File download: https://files.banggood.com/2017/10/SKU759597.zip Deceleration stepper motor: Diameter: 28mm Voltage: 5V Stepping angle: 5.625 x 1/64 Reduction ratio: 1/64 5-wire 4-phase can be driven with ordinary uln2003 chip can also be used in conjunction with the use of two-phase development board, can be used directly plug, easy to use stepper motor in the development board Package includes: 5 x Stepper motor 5 x Driver board 1 x Dupont cable (Male to female),,,,
R 299
See product
South Africa (All cities)
5Pcs PFM Control DC-DC 0.9V-5V Step-up Power Supply Module Description: Mini PFM Control On-board input voltage indicator High conversion efficiency, maximum to 96% Any DC voltage input 0.9V ~ 5V, output 5V DC voltage can be stable, with two AA batteries input to the output current of 500-600MA, single AA battery power supply output current about 200MA On-board USB female, can supply power directly to the USB interface Small dimension Specification: Input voltage: 0.9 - 5V DC Output voltage: 5V DC PCB size: 34mm x 16.2mm Applications: DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Package included: 5 x Mini PFM control DC-DC USB 0.9V-5V to 5V DC boost step-up
R 73
See product
South Africa (All cities)
5Pcs 1.5V 1.8V 2.5V 3V 3.7V 4.2V 5V TO 3.3V DC-DC Boost Converter Module Step Up Board Package contains 1 X item of the smallest listed variant.
R 370
See product
South Africa (All cities)
5pcs TCRT5000 950mm 5V 3A Infrared Reflective Optical Sensor For Tracking Car
R 300
See product
South Africa (All cities)
5pcs Vertical ACDC220V to 5V 400mA 2W Switching Power Supply Module For Smart Home
R 480
See product
South Africa (All cities)
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board Without Decoding -105dBm Package contains 1 X item of the smallest listed variant.
R 270
See product
South Africa (All cities)
5pcs BESTEP 1 Channel 5V Low Level Solid State Relay Module With Fuse 250V2A For Auduino Package contains 1 X item of the smallest listed variant.
R 400
See product
South Africa
5Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 5 x LED module 5 x Dupont line (5P-20cm)
R 291
See product
South Africa
5Pcs 24 Bit AD HX711 Weighing Pressure Sensor Module For Arduino Description: The module uses 24 high-precision A / D converter chip HX711, is designed specifically for high-precision electronic scales, two analog channel input, the internal integration of 128 programmable amplifier gain of. The input circuit can be configured for electrical bridge (bridge pressure as the pressure weighing) sensor mode is ideal for high-precision, low-cost sampling front-end module   Specification: Module Operating voltage: 4.8V-5.5V Typical current: 1.6mA Size: 2.9 x 1.7 x 0.4cm Typical operating current: Operating voltage range: 2.6V ~ 5.5V Operating temperature range: -20 to +85 °C Package included: 5 x  HX711 Weighing Pressure Sensor
See product
South Africa (All cities)
5Pcs NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator Features: 1. As a square wave signal generator,generates a square wave signal used for experimental development. 2. Used to drive a stepper motor for generating a square wave drive signal. 3. Generate adjustable pulse for MCU. 4. Generate adjustable pulse,to control circuitry associated. 5. Size: 31mm x 22mm 6. Main chip: NE555 7. Input Voltage: 5V-15V DC. When power supply is 5V, the output current can be 15 MA around; when 12V power supply, the output current can 35 MA around 8. Input current: >=100 MA 9. Output amplitude: 4.2V V-PP to 11.4V V-PP. (Different input voltage, the output amplitude will be different) 10. Maximum output current: >=15MA (5V power supply, V-PP greater than 50%), >=35MA (12V power supply, V-PP greater than 50%) 11. Output with LED indication(low level,LED will on; high level,LED will off;low frequency, the LED flashes) 12. The output frequency range is selectable: LF file: 1Hz ~ 50Hz IF file: 50Hz ~ 1kHz High-frequency file: 1KHz ~ 10kHz HF file: 10kHz ~ 200kHz 13.The output duty cycle can fine-tune; duty cycle and frequency is not separately adjustable; adjusting the duty cycle will change the frequency Package included: 5 x NE555 Pulse Frequency Duty Cycle Adjustable Module
R 113
See product
South Africa (All cities)
5Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 5 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module
R 565
See product
South Africa (All cities)
5Pcs Adjustable XL6009 Step Up Boost Voltage Power Supply Module Converter Regulator Feature: Solidly-structured Built-4A efficient MOSFET switch, so that the efficiency up to 94% Ultra-high switching frequency, you can use a small-capacity filter capacitors that can achieve very good results Specification: Input voltage: 3.5V ~ 32V Output voltage: 5V ~ 35V Output current: rated current is 2.5A, maximum 3A (Additional heatsink is required) Load regulation: ±0.5% Voltage regulation: ±0.5% Work Temperature: -40°C ~ +125°C Maximum power: 10W Size: 4.1 x 2.1 x 1.3cm Note: This can't be used to step down voltage Package included: 5 x XL6009 step up voltage module
R 197
See product

Free Classified ads - buy and sell cheap items in South Africa | CLASF - copyright ©2024 www.clasf.co.za.