5pcs 5v 30v dc

Buy 5pcs 5V 5A DC USB Buck Module USB Charging Step Down Power Board... for R489.00

5Pcs 5V 1-Channel H/L Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 5 x 1 Channel H/L trigger optocoupler relay module

5Pcs 5V To 3.3V DC-DC AMS1117 800MA Step-Down Power Supply Buck Module Features: Size: 8.6 x 12.33 mm Input voltage: DC 4.2 V - 10 V Output: 3.3 V, 800 mA Note: 1.Boost modules or buck module indicate the operating voltage, Please do not exceed operating voltage, or it will be damaged easily! 2.Boost module output voltage can only be greater than or equal to input voltage, cannot be less than the input voltage! 3.Buck module input voltage must be higher than output voltage of 1.5V or 2V, otherwise it can not output enough power! 4.Automatic Adjustable Boost or Buck module has start voltage and limit working voltage, Please do not exceed them, or it will be damaged easily! 5.Cannot reverse polarity, or it will be short circuit, or will be born easily! Package included: 5 x Step-down module

5Pcs 5V Infrared Line Tracking Sensor Module For Arduino Feature: Quantity: 5pcs Size: 3.5 x 1cm Power supply: 5V DC Detector distance: 10mm Build-in Tcrt5000 Sensor NSOR Applicable to a variety of platforms including Arduino / AVR / ARM /PIC Package included: 5 x Tracking Sensor Module  

Buy 5Pcs DC 4.5V To DC 35V 5A 90W Mini DC Motor PWM Speed Controller Module Speed R for R299.00

Buy 5pcs 3A 15W DC 12V To DC 5V Dual USB Power Charger Adapter Converter Module for R443.46

Buy 5pcs USB Power Boost Line DC 5V to DC 12V Step UP Module USB Converter for R206.07

Buy 5pcs 3A 15W DC 12V To DC 5V Dual USB Power Charger Adapter Converter Module for R419.00

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 5 x 5V 1 channel relay module 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino 5Pcs 5V Relay 5-12V TTL Signal 1 Channel Module High Level Expansion Board For Arduino

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Specification: Input Power Supply: 12V DC Load Voltage: AC240V 2A Maximum operating current: 13.8mA Trigger mode: low level Input control signal voltage: (0-2.5V low state relay OFF) (3.3-5V state high relay ON) Blue KF301 terminal connection control line is more convenient. Module interface: DC +: positive power supply (by relay voltage power supply) DC-: connect power negative CH: Relay Module signal triggering end (Low level trigger effective) Note: Power must be DC voltage and need to be consistent with the voltage relay Package Included: 5 x Low Level Relay Module 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A 5pcs 1 Channel DC 12V Relay Module Solid State Low Level Trigger For Arduino 240V2A

Buy 5Pcs Low Voltage DC 1.8V 3V 5V 6V 12V 2A Motor Speed Controller PWM 1803B... for R459.00

Buy 5pcs IO15B01 6A DC 3V 3.3V 3.7V 5V Electronic Switch Latch Bistable Self-locking Trigger Module Boar for R376.00

Description: Trigger mode: High level 5V relay module Can be used for microcontroller development board module or home appliance control 5V - 12V TTL control signal Can control DC or AC signal, also 220V AC load Normally open / closed contact Power indicator Controlled lights bright when pull and not shine when disconnect Increase the transistor drive relay coils, control pins high impedance Control pins have pull down circuit to prevent malfunction of relay vacant Package included: 5 x 5V 1 channel relay module

Output Voltage: DC5V / 3.3V / USB Atmega328P ATmega16U2 With USB cable version Description: UNO R3 board is 100% compatible with original Arduino, now it has perfect quality and performance. Arduino is an open-source physical computing platform based on a simple i/o board and a development environment that implements theProcessing/Wiring language. Arduino can be used to develop stand-alone interactive objects or can be connected to software on your computer (e.g. Flash, Processing, MaxMSP). The open-source IDE can be downloaded for free (currently for Mac OS X, Windows, and Linux). This is the new Tosduino Uno R3. In addition to all the features of the previous board, the Uno R3 now uses an ATmega16U2 instead of the ATmega8U2 chip. This allows for faster transfer rates, no drivers needed for Linux or Mac (inf file for Windows is needed), and the ability to have the Uno show up as a keyboard, mouse, joystick, etc. Note: The TOSduino Uno R3 requires the Arduino 1.0 drivers folder in order to install properly on some computers. We have tested and confirmed that the R3 can be programmed in older versions of the IDE. However, the first time using the R3 on a new computer, you will need to have Arduino 1.0 installed on that machine. The small chip is ATmega16U2, the 28 pin DIP socket chip is ATmega328-pu. Performance description: Digital I / O digital input / output terminal: 0 to 13. Analog I / O Analog inputs / outputs: 0 to 5. Support ISP download function. Input voltage: No external power supply when connected to the computer USB, external power supply 5V ~ 9V DC voltage input. Output voltage: 5V / 3.3V DC. Using Atmel Atmega328 microprocessor controller. Package included: 5 x UNO R3 5 x USB cable

5Pcs PFM Control DC-DC 0.9V-5V Step-up Power Supply Module Description: Mini PFM Control On-board input voltage indicator High conversion efficiency, maximum to 96% Any DC voltage input 0.9V ~ 5V, output 5V DC voltage can be stable, with two AA batteries input to the output current of 500-600MA, single AA battery power supply output current about 200MA On-board USB female, can supply power directly to the USB interface Small dimension Specification: Input voltage: 0.9 - 5V DC Output voltage: 5V DC PCB size: 34mm x 16.2mm Applications: DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Package included: 5 x Mini PFM control DC-DC USB 0.9V-5V to 5V DC boost step-up