3pcs rs232 module

Buy 3pcs RS232 Module with DB9 Connector RobotDyn for Arduino - products that work with official for Ard for R200.00

Buy 3Pcs RS232 SP3232 Serial Port To TTL RS232 to TTL Serial Module With Brush Line 3V To 5.5V for R516.64

Buy 3Pcs RS232 TTL HC-06 Wireless bluetooth RF Transceiver Serial Module for R445.00

Buy 3Pcs RS232 TTL HC-06 Wireless bluetooth RF Transceiver Serial Module for R537.31

Buy 3Pcs LM386 Module 20 Times Gain Audio Amplifier Module With Adjustable Resi for R159.00

Buy 3pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module for R286.00

Buy 3pcs HX711 Module + 20kg Aluminum Alloy Scale Weighing Sensor Load Cell Kit for R383.25

Buy 3Pcs GY-BMI160 Module 6DOF 6 Axis Angular Velocity Gyroscope + Gravity Acceleration Sensor IICSPI for R356.00

Feature: Note: This module does not suitable for IOS system. TTL data transparent transfer between a host Bluetooth device Build-in CSR company Bluetooth chip BC417143 Bluetooth specification v2.0 + EDR Works with any USB Bluetooth adapters Default Baud Rate: 9600, pairing code 1234, the working mode SLAVE Coverage up to 30ft Built in antenna Mini Size Using mainstream CSR Bluetooth chip, Bluetooth V2.0 protocol standards Serial module operating voltage 3.3V, 10 meters from the general The working current: pairing: 30mA ~ 40mA Sleep current: not sleep For GPS navigation systems, utility meter reading systems, industrial control systems mining site Can be used with a Bluetooth laptop computer plus a Bluetooth adapter, PDA and other devices to connect seamlessly   Specification: Power input: +3.3V DC Signal coverage: 30ft Size: 26.9 x 13 x 2.2mm Application: This module is mainly used for wireless transmission of data in the field a short distance. And PC can be easily connected Bluetooth device, you can also exchange data between two modules. Avoid cumbersome cable connections, direct serial cable replacement.   Package included: 3 x HC-06 30ft wireless bluetooth RF transceiver module

Buy 5pcs RS232 Module with DB9 Connector RobotDyn for Arduino - products that work for R254.04

Buy 30pcs RS232 Module with DB9 Connector RobotDyn for Arduino - products that work for R1,385.77

3Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 3 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

3Pcs 3V To 5V 1A USB Charger DC-DC Converter Step Up Boost Module Features: Module uses the Taiwan production boost chip, high efficiency (up to 92%), plus built-in over-current protection chip, can be more good to protect the module and use the device after the class. Module with undervoltage protection, undervoltage protection into state below 2.5V, can be more better protect the battery, to avoid excessive discharge. Module can modify the fixed resistor adjusts the output voltage can be adjusted up to 12V output, but to ensure that the output power of less than 5W. This module uses TDK multilayer ceramic capacitors as main filter capacitor, the output ripple can be as low as 20mV (5V1A output case)! This module uses a standard USB interface, you can use all universal USB charging mobile phones, MP3, MP4 and other equipment, the perfect support for IPHONE and other mobile phone. Specification: Module properties: Non-isolated step-up module (BOOST) Input voltage: 2.5-6V Output voltage: 4-12 V(Adjustable, the default 5 v) Output current: 1000mA (Max) Efficiency: 92%(Max) (the higher the input voltage, the higher the efficiency) Switching frequency: 1MHz Output ripple: 20mV (MAX) Operating temperature: Industrial (-40°c to +85°c) Voltage regulation: ±2.5% Short circuit protection: None (please use the lithium battery with protection) Input: IN + postive, IN - negative Output: USB output Size: 3 x 1.3 x 0.8 cm Application: This module can be used for DIY mobile power output, enabling single or two ordinary lithium battery to 5V boost to the mobile phone or PSP device charging. DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Note: This module is a fixed 5V output module Modules indicated above IN - (negative input), IN + (positive input), OUT-(negative output), OUT + (positive output) must be connected correctly, otherwise it may cause damage to the module This module has an LED light, when the charge when the LED lights can be used as indicator Package included: 3 x USB boost module

3Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 3 x LED module 3 x Dupont line (5P-20cm)

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module