3pcs lm386 module

Buy 3Pcs LM386 Module 20 Times Gain Audio Amplifier Module With Adjustable Resi for R159.00

Buy 3pcs LM386 DC 3-12V 3.5mm Super Mini Audio Amplifier Board Module Audio Power Electronic Kit for R175.00

Buy 3pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module for R286.00

Buy 3pcs RS232 Module with DB9 Connector RobotDyn for Arduino - products that work with official for Ard for R200.00

Buy 3pcs HX711 Module + 20kg Aluminum Alloy Scale Weighing Sensor Load Cell Kit for R383.25

Buy 3Pcs GY-BMI160 Module 6DOF 6 Axis Angular Velocity Gyroscope + Gravity Acceleration Sensor IICSPI for R356.00

Features: 1. Onboard LM386 Chip 2. 200 multiplier benefits circuit design 3. On-board speaker wiring block 4. On-board 10K variable resistor, you can adjust the volume of the enlarged 5. On-board power indicator 6. The chip pin leads, can be directly input audio signal 7. Operating voltage: 5 - 12V 8. Board size: 41 x13mm Package includes: 3 x  LM386 audio amplifier module

Feature: 1. On-board LM386 Chip 2. 20 times gain circuit design 3. On-board speaker wiring Block 4. On-board 10K variable resistor, you can adjust the volume of the amplifier 5. On-board power indicator 6. The chip pin was leaded, can be directly input audio signal 7. Operating voltage: 5 ~ 12V 8. Size: 41mm*13mm Package included: 5 x LM386 Module 20 Times Gain Audio Amplifier Module

3Pcs HC-12 433 SI4463 Wireless Serial Module Remote 1000M With Antenna Note: HC-11 cannot communicate with the HC-12, they work independently, in pairs Features: Supply voltage: 3.2V~5.5V. (If the module you want to work long hours in the emission state, it is recommended that when the supply voltage exceeds 4.5V threaded a 1N4007 diode to prevent module built-in LDO heated) Default address range (open field test): About 600m (maximum communication distance adjustable reach 1000m, the baud rate is 5000bps) Default idle current: 16MA (In different working modes operating current is different) Module dimensions: 27.8 x 14.4 x 4mm Operating frequency range: 433.4-473.0MHz, up to 100 channels of communication The maximum transmit power: 100mW (settable) Module support software upgrade Default factory settings: Mode FU3, baud rate is 9600bps, communication channels CH001 (433.4M) Package included: 3 x HC-12 433 Serial module AT command set:   Module parameters, AT command set AT command is used to set the parameters of the function module and switching modules need to exit the setting mode after setting to take effect. Meanwhile, modify the parameters and functions, power-down is not lost.   Enter the command mode: The first entry mode - normal use (has the power) in the first 5-pin "SET" is set low; The second mode of entry - power, 5th pin "SET" again first set low on power. Both methods can make the module into AT command mode, release ("SET" pin is not connected low) to exit command mode. After the exit command mode, if you change the module function, the function will be cut to the appropriate state. The second way is fixed in serial format 9600, N, 1 into the AT.   Instructions: 1. AT Test instructions Example: Send module commands "AT", the module returns "OK".   2. AT + Bxxxx Change the serial port baud rate command. You can set the baud rate is 1200bps, 2400bps, 4800bps, 9600bps, 19200bps, 38400bps, 57600bps and 115200bps. The factory default is 9600bps. Example: Set the module serial port baud rate is 19200bps, please send module command "AT + B19200", the module returns "OK + B19200".   3. AT + Cxxx Change the wireless communication channel, selectable from 001 to 127 (more than 100 radio channels after the communication distance not guaranteed). The default value is 001 radio channels, operating frequency is 433.4MHz. Step channel is 400KHz, the operating frequency of the channel 100 is 473.0 MHz.   Example: Set module to channel 21, please send module command "AT + C021", the module returns "OK + C021". After exiting the command mode, the module in the first 21 channels, operating frequency is 441.4 MHz. Note: Because the wireless receiver module sensitivity HC-12 is relatively high, the baud rate is greater than when air 58000 bps, 5 must be shifted to the adjacent channel use. When the air baud rate is not greater than 58000 bps, if the short distance (10 meters) communication, but also need to stagger five adjacent channel use.   4. AT + FUx Change the module serial pass-through mode, there FU1, FU2 and FU3 three modes. Module default mode is FU3, two serial pass-through mode module must be set to the same communication. See detailed above, "wireless serial pass-through" part. Example: Send module commands "AT + FU1", the module returns "AT + OK".   5. AT + Px The default setting is 8, maximum transmit power, communication distances. Transmit power level is set to 1, the minimum transmission power. In general, the transmission power of each drop 6dB, communication distance will be reduced by half. Example: Send module commands "AT + P 5", the module returns "OK + P5". After exiting the command mode, the module transmit power is +11 dBm. Package included: 1 x HC-12 module

3Pcs 3V To 5V 1A USB Charger DC-DC Converter Step Up Boost Module Features: Module uses the Taiwan production boost chip, high efficiency (up to 92%), plus built-in over-current protection chip, can be more good to protect the module and use the device after the class. Module with undervoltage protection, undervoltage protection into state below 2.5V, can be more better protect the battery, to avoid excessive discharge. Module can modify the fixed resistor adjusts the output voltage can be adjusted up to 12V output, but to ensure that the output power of less than 5W. This module uses TDK multilayer ceramic capacitors as main filter capacitor, the output ripple can be as low as 20mV (5V1A output case)! This module uses a standard USB interface, you can use all universal USB charging mobile phones, MP3, MP4 and other equipment, the perfect support for IPHONE and other mobile phone. Specification: Module properties: Non-isolated step-up module (BOOST) Input voltage: 2.5-6V Output voltage: 4-12 V(Adjustable, the default 5 v) Output current: 1000mA (Max) Efficiency: 92%(Max) (the higher the input voltage, the higher the efficiency) Switching frequency: 1MHz Output ripple: 20mV (MAX) Operating temperature: Industrial (-40°c to +85°c) Voltage regulation: ±2.5% Short circuit protection: None (please use the lithium battery with protection) Input: IN + postive, IN - negative Output: USB output Size: 3 x 1.3 x 0.8 cm Application: This module can be used for DIY mobile power output, enabling single or two ordinary lithium battery to 5V boost to the mobile phone or PSP device charging. DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Note: This module is a fixed 5V output module Modules indicated above IN - (negative input), IN + (positive input), OUT-(negative output), OUT + (positive output) must be connected correctly, otherwise it may cause damage to the module This module has an LED light, when the charge when the LED lights can be used as indicator Package included: 3 x USB boost module

3Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit For Arduino Specifications: A single module can drive an 8 x 8 common cathode lattice Operating voltage: 5V Size: 5 x 3.2 x 1.5 cm (L x W x H) LED color: Red With four screws hole, aperture 3mm With input and output interfaces, supports multiple modules cascade Wiring instructions: 1. The module left side as an input port and the output port on the right 2. To control a single module, just connect the input port to the CPU 3. When cascading multiple modules, the input port of the first module connect to the CPU, the output port connect to the input port of the second one, and so on. In the case of 51 MCU: VCC → 5V GND → GND DIN → P22 CS → P21 CLK → P20 Note: 1. VCC and GND is not reversed, it would burn the chip! 2. When the 51 microcontroller P0 port controlling, must be connected to the pull-up resistor, it is recommended that the resistance of 4.7K--10K 3. Please install lattice into the round hole first, and then insert the round hole to PCB board and weld. Face the side of lattice with words, from left to right pin order is 123456. PCB board 1st pin is square pad! 4. Electrolytic capacitors long-pin as positive, short-pin as negative; ceramic capacitor hsa no positive and negative points Package included: 3 x LED module 3 x Dupont line (5P-20cm)

3Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 3 x Micro SD TF card module

3Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 3 x 1 Channel H/L level trigger optocoupler relay module

3Pcs Soil Hygrometer Humidity Detection Moisture Sensor For Arduino Description: This is a summary of the soil moisture sensor can be used to detect moisture, when the soil is dry, the module outputs a high level, whereas output low. Using this sensor make an automatic watering system, so that your garden plants without people to manage. Operating voltage: 3.3V~5V. Adjustable sensitivity (shown in blue digital potentiometer adjustment) Dual output mode,analog output more accurate. A fixed bolt hole for easy installation. With power indicator (red) and digital switching output indicator (green). Having LM393 comparator chip, stable. Panel PCB Dimension: 3cm x 1.5cm. Soil Probe Dimension: 6cm x 2cm. Cable Length: 21cm. VCC: 3.3V-5V. GND: GND. DO: digital output interface(0 and 1). AO: analog output interface. Instructions for Use: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. 2. Module to reach the threshold value is set in the soil moisture, DO port output high, when the the soil humidity exceeds a set threshold value, the module D0 output low. 3. The digital output D0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. 4. The digital outputs DO shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. 5. Analog output AO and AD module connected through the AD converter, you can get more precise values of soil moisture. Package Included: 3 x Soil moisture detector module 3 x Probe 3 x 2P Jumper Cable

3Pcs 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module With Antenna Desription: NRF24L01P + PA + LNA Division for the ultra-long-distance data transmission, specially developed high-power and high sensitivity wireless module 2.4G ISM band NRF24L01P + PA + LNA wireless module to work in the license-free that can be point-to-point applications or be composed of a star network. Digital transmission chip NRF24L01+ with the Division of Professional Design professional full two-way RF power amplifier high power PA and LNA chip, RF switches and band pass filters, makes effective communication distance greatly expand.   RF part, it has been done a lot of optimization matching debugging. The emission efficiency to achieve the highest harmonic minimum and make NRF24L01P + PA + LNA wireless module of RF interference to the external equipment reaches minimum, while not susceptible to interference from other devices. NRF24L01P + PA + LNA wireless module integration is extremely high, the size is 41mm x 15.5mm to make conveniently embedded. Package included: 3 x 1100 Meter Long Distance NRF24L01+PA+LNA Wireless Module With Antenna