24v lithium

24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For Package weight: 0.41 kg Description: 1. Moto controller and LCD display adapts waterproof design, you can use it Conveniently at your daily time. 2. LCD display can clearly show the state and data, backlight enables you to see screen clearly in dim environment, buttons for quick operation, easy to use. 3. Brushless type of controller, working silently and sensitive to the state of electric bike. 4.LCD display comes with mount,suitable for 22mm handlebar. 5. Suitable for electric bicycles, cars, scooters. 6. Easy to install and use, comes with mount for LCD display and suitable for 22mm handlebar. 7. Fit for different battery: lead-acid, Li-Fe battery, LNCMO battery {Li(NiCoMn)O2}, and so on. For different material there is different under voltage protecting point. 8. Fit for DC brushless gear motor lower than 350w, and gearless motor, and high speed motor and so on 9.Suitable for: 250W/350W brushless DC motor (include with hall sensor and without hall sensor) Specification: Brushless Motor Controller: Voltage:DC 24V/36V/48V/60V Power:250W/350W Low volts:DC 19V/30V/41V/52V Max current available: 10A-20A (default setting 13A) 60° / 120° (Automatically indentify) Operating Conditions: -40￢ﾄﾃ ~80￢ﾄﾃ Material: Plastic + Metal Controller Function: 1. 1:1 pas power 2. Brake and cut off power 3. Connect with lcd display 4. Throttle 5. Horn/light power port 6. Self learning 7. Hall linear ebs brake 8. Cruise 9. 6km/h boosting Controller Feature: 1. Automatically indentify motor phase and angle 2. Dual mode (When motor hall work normally, controller work with hall mode. When motor hall damaged, controller can intelligently test it and change to no-hall mode and keep on work. (other controller if not double mode, cannot work if motor hall damaged) 3. Can control and match with other electric parts 4. When battery voltage is not enough the controller will automatically lower current, this will protect your battery for longer life. LCD Display: Brief introduction to 6 mosfet controller dual mode type for lithium battery Rated working voltage: 24V/36V/48V/60V Power available:250W/350W Max current available: 10A-20A (default setting 13A) Battery Voltage Undervoltage Protection Point: DC 19V/30V/41V/52V LCD Display Function: Battery indicator, Motor power indicator, speed stage, bike speed indicator, single trip distance, total trip distance, single trip time, battery detailed voltage, cruise control, assis control. 1. Adjust the brightness of backlight 2. Unit Changing, kilometer to mile, or mile to kilometer 3. Automatically indentify the voltage of battery 4. Sleep Time and Time Display Setting 5. Gear Setting 6. Accurate speed parameters 7. Limit the speed, speeding will brake 8. Start Mode Setting 9.Drive Mode Setting 10.Adjust the boost sensitivity 11. Change the strength and weakness of boost 12. Compatible magnetic points 13. Current and low voltage of controller setting 14. Total mileage accumulation and clearing 15. Cruise 16. Power-on password setting 17. 6km/h boosting and boosting at current speed LCD Display Error Code: 002 brake error 003 pas sensor error 004 boosting, 6km/h cruise mode 005 timely cruise mode 006 battery level low 007 motor error 008 throttle error 009 controller error 010 communication receive error 011 c Click here for more deals 24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For 24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For

Buy 24V 30bar Cordless Lithium Battery Portable Power Cleaner for Car Cleaning Tool for R2,567.62

Buy 24V 30bar Cordless Lithium Battery Portable Power Cleaner for Car Cleaning Tool for R2,609.08

Buy 24V 2A Lithium Battery Car Electromobile Sprayer Lawn Mower Lighting Battery Charger, CN Plug for R462.24

Description: This twist grip using digital display battery voltage display the remaining battery power, regardless of lithium batteries, lead acid batteries, aqueous batteries, dry batteries, below 100V electric vehicles can be used, it can automatically identify the voltage, real-time display. Fit for 22.2mm diameter Handlebar Suitable for 24~48V E-bike Specification: Product Size: 115 x 33mm Cable Length: About 1.8m Yellow Wire: Power +  24V 36V 48V Red Wire: +5V Green Wire: signal Black Wire: - Blue Wire: I/O button,such as light,  horn White Wire: I/O button, such as light, horn Please do not contact wrong wire   Note: Maximum voltage indicates fully charged. Low voltage indicates the battery runs out. Before the minimum voltage necessary to charge the battery. 12V electric car, the maximum voltage of about 12V, about the minimum 9V (battery is runs out.) 24V electric car, the maximum voltage of about 29V, the lowest of about 21V (charge) 36V electric car, the maximum voltage of about 42V, the lowest of about 29V (charge) 48V electric car, the maximum voltage of about 54V, the lowest of about 39V (charge) 60V electric car, the maximum voltage of about 72V, the lowest of about 49V (charge) 72V electric car, the maximum voltage of about 84V, the lowest of about 60V (charge) Package Included: 2 X EBike Throttle Grip (With Wire) 2 X Keys

SELECTED OPTION: COLOR: SILVER CLICK HERE for more options in this item. Description: This twist grip using digital display battery voltage display the remaining battery power, regardless of lithium batteries, lead acid batteries, aqueous batteries, dry batteries, below 100V electric vehicles can be used, it can automatically identify the voltage, real-time display. Fit for 22.2mm diameter Handlebar Suitable for 24~48V E-bike Specification: Product Size: 115 x 33mm Cable Length: About 1.8m Yellow Wire: Power +  24V 36V 48V Red Wire: +5V Green Wire: signal Black Wire: - Blue Wire: I/O button,such as light,  horn White Wire: I/O button, such as light, horn Please do not contact wrong wire   Note: Maximum voltage indicates fully charged. Low voltage indicates the battery runs out. Before the minimum voltage necessary to charge the battery. 12V electric car, the maximum voltage of about 12V, about the minimum 9V (battery is runs out.) 24V electric car, the maximum voltage of about 29V, the lowest of about 21V (charge) 36V electric car, the maximum voltage of about 42V, the lowest of about 29V (charge) 48V electric car, the maximum voltage of about 54V, the lowest of about 39V (charge) 60V electric car, the maximum voltage of about 72V, the lowest of about 49V (charge) 72V electric car, the maximum voltage of about 84V, the lowest of about 60V (charge) Package Included: 2 X EBike Throttle Grip (With Wire) 2 X Keys

Options: Description: This twist grip using digital display battery voltage display the remaining battery power, regardless of lithium batteries, lead acid batteries, aqueous batteries, dry batteries, below 100V electric vehicles can be used, it can automatically identify the voltage, real-time display. Fit for 22.2mm diameter Handlebar Suitable for 24~48V E-bike Specification: Product Size: 115 x 33mm Cable Length: About 1.8m Yellow Wire: Power + 24V 36V 48V Red Wire: +5V Green Wire: signal Black Wire: - Blue Wire: I/O button,such as light, horn White Wire: I/O button, such as light, horn Please do not contact wrong wire Note: Maximum voltage indicates fully charged. Low voltage indicates the battery runs out. Before the minimum voltage necessary to charge the battery. 12V electric car, the maximum voltage of about 12V, about the minimum 9V (battery is runs out.) 24V electric car, the maximum voltage of about 29V, the lowest of about 21V (charge) 36V electric car, the maximum voltage of about 42V, the lowest of about 29V (charge) 48V electric car, the maximum voltage of about 54V, the lowest of about 39V (charge) 60V electric car, the maximum voltage of about 72V, the lowest of about 49V (charge) 72V electric car, the maximum voltage of about 84V, the lowest of about 60V (charge) Package Included: 2 X EBike Throttle Grip (With Wire) 2 X Keys

Description: This twist grip using digital display battery voltage display the remaining battery power, regardless of lithium batteries, lead acid batteries, aqueous batteries, dry batteries, below 100V electric vehicles can be used, it can automatically identify the voltage, real-time display. Fit for 22.2mm diameter Handlebar Suitable for 24~48V E-bike Specification: Product Size: 115 x 33mm Cable Length: About 1.8m Yellow Wire: Power + 24V 36V 48V Red Wire: +5V Green Wire: signal Black Wire: - Blue Wire: I/O button,such as light, horn White Wire: I/O button, such as light, horn Please do not contact wrong wire Note: Maximum voltage indicates fully charged. Low voltage indicates the battery runs out. Before the minimum voltage necessary to charge the battery. 12V electric car, the maximum voltage of about 12V, about the minimum 9V (battery is runs out.) 24V electric car, the maximum voltage of about 29V, the lowest of about 21V (charge) 36V electric car, the maximum voltage of about 42V, the lowest of about 29V (charge) 48V electric car, the maximum voltage of about 54V, the lowest of about 39V (charge) 60V electric car, the maximum voltage of about 72V, the lowest of about 49V (charge) 72V electric car, the maximum voltage of about 84V, the lowest of about 60V (charge) Package Included: 2 X EBike Throttle Grip (With Wire) 2 X Keys

30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD Package weight: 0.22 kg Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:30A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 X 10A PWM Solar Charge Controller 1 X Screwdriver 1 X Manual Click here for more deals 30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD 30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD

10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD Package weight: 0.21 kg Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:10A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 x 10A PWM Solar Charge Controller 1 x Screwdriver 1 x Manual Click here for more deals 10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD 10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD

Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:20A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 X 10A PWM Solar Charge Controller 1 X Screwdriver 1 X Manual

12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter Package weight: 0.02 kg Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable Click here for more deals 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X 12V Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm   Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds   Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid   Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals)   Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B Package weight: 0.88 kg Description: The difference between manual and automatic mode: 1. Manual: It can be used for small capacity, Low temperature(under 0 ° C) and large Internal resistancethe battery, charging current is bigger than automatic so it take less time than automatic, but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can’t more than 1 hour! 2. Automatic:pulg AC power first then connect battery with charger, it will recognize volgate automatic,telligent and convenient. Highly recommended: in the winter(under 0 ° C), use automatic mode to charge full first then use manual mode for 0.5-1 hours. 3. LED screen: it shows both charging voltage and current, 4. Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off 5. Red is anode,black is cathode Specification: Input Voltage: AC150-250V Output voltage: 12V/24V automatic Suitable capacity: 6AH-200AH Full load conversion efficiency: 93% Power: 220W Frequency: 50-60HZ Length of power cord wire:125cm Plug: US Plug Type: Charger Automatic, LED Light, Plug in, Portable, Reverse Polarity Protection, Safety Switch, Trickle Charging Stage: 1. Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; 2. Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger’s current and output voltage accurate,avoid overcharge; 3. Trickle charge mode: when the battery voltage and current is approaching the set voltage and current,it will turn to trickle floating charge from automatic mode, it means charge full,also can be charged with floating mode. Package Included: 1 X Charger 1 X User Manual 2 X Replace Clips Click here for more deals 12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B 12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium B

Buy 3.7V 4.2V 7.4V 12V 16.8V 24V 36V Lithium Battery Capacity Indicator 1S 2S 3S 5S for R163.74

Buy 2V 24V 100AH Battery Charger For Lead Acid Lithium Batteries for R946.39

Buy ANJING 600W 12V/24V 25A Pulse Repair Battery Charger Lithium Battery Lead-Acid for R2,364.13

SELECTED OPTION: ADAPTOR: US CLICK HERE for more options in this item. Description: The difference between manual and automatic mode: Manual: It can be used for small capacity,Low temperature(under 0 ° C) and large Internal resistancethe battery,charging current is bigger than automatic so it take less time than automatic,but there must has human monitoring to avoid damage battery, when the battery shell has temperature must stop charging!using manual mode can't more than 1 hour! Automatic:pulg AC power first then connect battery with charger,it will recognize volgate automatic,telligent and convenient. Highly recommended:in the winter(under 0 ° C),use automatic mode to charge full first then use manual mode for 0.5-1 hours. LED screen: it shows both charging voltage and current, Identify 12V/24V intelligent,the charging light will bright when charging,when charging full the light will off -Red is anode,black is cathode   Specification: Input Voltage: 110-250V Output voltage: 12V/24V automatic Current: 10A peak for 12V /7A peak for 24V Suitable Capacity: 10-100AH Power: 180W Frequency: 50-60HZ Length of Output Wire: 50-60cm Length of Input Wire: 120cm Type: Charger Features: Automatic, LED light, plug in, portable, reverse polarity protection, safety switch, trickle   Charging Stage: Constant current: means the battery voltage is lower than the set voltage of charger, then the charger supply constant charging current to maintenance both battery and battery charger; Constant Voltage: advanced pulse width modulation (PWM) technology, control the charger's current and output voltage accurate,avoid overcharge; Trickle charge mode: when the battery voltage and current is approaching the set voltage and current, it will turn to trickle floating charge from automatic mode,it means charge full,also can be charged with floating mode.   Package Included: 1 X Charger 1 X User Manual

12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium Battery

Buy 12V/24V 100AH Battery Charger Intelligent Acid Pulse Repair Type Lead Acid Lithium for R646.00

Buy HTRC 12V/24V 10A/5A 7-Stage Touch Screen Pulse Repair LCD Battery Charger For Lithium for R700.91

Buy 12V/24V 25A 6-400Ah 600W High-power Pulse Repair LCD Battery Charger For Car Motorcycle Lithium Lead for R1,940.00

Buy 12V 24V 200AH 220W Car Motorcycle Battery Charger Pulse For Lead Acid Lithium Battery for R763.00

Please take note: Images provided are for illustration purposes only and actual products might differ slightly. All product information is obtained directly from our suppliers. We cannot be held responsible for any errors or omissions (E&OE). If you would like to confirm details on any product please give us a call or pop us an email. Ultra-compact, rugged, and portable UltraSafe® Smart Charger. Features spark proof technology and reverse polarity protection. Charges 2X faster than ordinary chargers. Stay connected 24/7 with zero overcharge. NOCO 12V & 24V 7.2A Ultrasafe Smart Battery Charger features: Start-Stop: Counteracts increased cyclic energy demands placed on batteries in micro-hybrid vehicles. Memory: Returns to last-selected mode when restarted. Maintenance Plus: Keeps the battery fully charged without over-charging, indefinitely. Diagnostics: Intuitive visual diagnostic tool for detecting reverse polarity, low-voltage or damaged batteries. Load Tracking: Dynamically changes charge current when a load is placed on the battery. Energy Save: Minimizes energy consumption when full power is not needed. Thermal Monitor: Internal temperature sensors adjust charge based on ambient climate. CANBUS: Automatically enables the charging port to charge CANBUS systems. Safe: Protects against reverse polarity, sparks, over-charging, overcurrent, open-circuits and overheating. Firewall: Multi-level safety barrier prevents unsafe and abnormal conditions. Interactive: Alters the charging process based on organic battery feedback. Rugged: Dirt, water, UV, impact and crush resistant. Recovery: Applies a high-voltage pulse charge when low-voltage, sulphation, or lost capacity is detected. Optimization: Stabilizes internal battery chemistry for increased performance and longevity. Efficiency: 85% approx Low voltage detection: 2V (12V), 14V (24V) Back Current Drain: Ambient Temperature: 0°C to +40°C Charger Type: 8 Step, Smart Charger Type of Batteries: 12V & 24V Battery Chemistries: Wet, Gel, MF, CA, EFB, AGM, LIB Battery Capacity: Up To 230Ah (12V), Up To 115Ah (24V), maintains all battery sizes Housing Protection: IP65 Cooling: Natural Convection Dimensions (LxWxH): 224mm x 94mm x 58mm Weight: 0.78 kg Charging Modes: Standby, 12V normal, 12V cold/AGM, 12V Lithium, 12V AGM+, 12V repair, 13.6V supply, 24V normal, 24V cold/AGM

12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle Package weight: 0.64 kg Description - Microprocessor Control (CPU) - 3-STAGE AUTOMATIC CHARGING: - Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. - Suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. -Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. - Switchmode technology - Polarity protection - Output short protection - Non battery link protection - Over voltage protection - Over temperature protection Specification: Input voltage: 100V-265V AC, 50-60Hz Rated output: 12V 8A / 24V 4A Color: Red Minimum start voltage: 2.0V Battery range: 2Ah-150Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85% Output Line Length: 65cm Input Wire Length: 110cm Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 170×98×58mm Cooling: Fan Scope of application: 12V/24V 2Ah-150Ah lead-acid batteries/start-up and shutdown batteries(lithium batteries can not be charged.) Note: This Charger is for battery capacity between 2AH to 150AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X 12V/24V Pulse Repair LCD Batteru Charger Click here for more deals 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle

12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD Package weight: 0.93 kg Description: LCD display at a glance Intelligent heat radiation, long service life Square lamp, safe and reliable, more convenient to operate Portable and durable, lightweight, easy to carry Advanced pulse width modulation (PWM)technology is used to automatically charge batteries through a 4-stage charging cycle The battery life can be significantly improved by digital pulse repairing method for the power chips of microcomputers Automatic Mode Advantages: When using automatic mode directly connected to the power supply and the battery on it, the charge without artificial regulation, the current will be fully automatic adjustment according to the battery needs to charge to a voltage location and automatic shutdown, the use of smart and convenient. Manual mode advantages: When the old battery is encountered, the ambient temperature is relatively low (below 0 °), and the battery capacity is slightly smaller, because of the large internal resistance of this type of battery, the trickle charging of small current occurs when using the automatic mode. Manual charging mode is aimed at such a large battery resistance characteristics of the design of the charging process, there are auxiliary repair battery function, the battery effect to play better. However, the use of manual mode charging must be artificially monitored, the battery case has a slight temperature, stop charging. Highly recommended: winter in the 0 ° below the environment, the battery to play a good time with the automatic mode is full, then manual mode, more than half an hour to 1 hour to make the battery performance better -Automatic charging mode: 12V battery charging, full voltage 13.8V-14.3V; manual charging mode: the maximum voltage of about 16V. The actual output current of 12V battery charging about 10A, 24V battery charging actual output current of about 7.5A The actual current depends on the demand for battery constant current constant voltage charging When the charge is completed, it will stop automatically at constant pressure, convert to trickle float mode, the constant current is about 0.2A The following is about the intelligent charger 12V battery reference charging time: (Actual charging completion time, the actual capacity of the battery may be) 6AH battery ~ 1-3 hours,7AH battery ~ 2--4 hours 9AH battery ~ 3 - 5 hours,10AH battery ~ 4 - 6 hours 20AH battery ~ 5--8 hours,32AH battery ~ 6 - 10 hours 36AH battery ~ 8-11 hours,45AH battery ~ 9-13 hours 55AH battery ~ 11--16 hours,60AH battery ~ 13--18 hours 80AH battery ~ 15--20 hours,105AH battery ~ 16--25 hours 120AH battery above, then analogize Specification: Material: Metal Input Voltage: 130V-250V Output Voltage: 12V-12A 24V-10A Power: 220W Frequency: 50-60HZ Name: Battery Charger Battery Type: Lead-acid battery Size: 15*19*7cm Power Cord Length: 120cm Weight: 750g Charging range: For the market 12v, 24v, 6AH-200AH of various types of batteries (except lithium iron battery) Packaged Included: Click here for more deals 12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD 12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD

AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display Package weight: 1.25 kg Description: Safety efficient,energy saving Technology of pulse width modulation Intelligent pulse repair type Manual adjustment or full automatic charger optional Automatic identification of 12V or 24V Compatible with lithium battery Specification: Wattage: 400W Input voltage:AC110-250V 50HZ-60HZ Full conversion rate:90%±3 Working temperature range:-30￢ﾄﾃ+40￢ﾄﾃ Rated voltage:12V/24V Constant current:18A±10% Charging current:10A±10% Constant voltage:14V±0.3 Charging voltage:28V±0.3 Size:21*16*8.7cm DC output line:60cm Power input line:130cm Package Included: 1 X Battery Charger 1 X User Manual Click here for more deals AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display

12V/24V 2-200ah Intelligent Pulse Repair Battery Charger Lead-acid For Motorcyc Package weight: 1.23 kg Description: 1. Protection function: reverse connection, low voltage, overheating, over current, short circuit, fire prevention, over voltage, electric shock. 2. The current can be manually selected 3A, 6A, 10A, or you can adjust the automatic default charging without adjusting. 3. 12V/24V automatic intelligent identification, suitable for 2-200AH lead-acid batteries.(Lithium battery disabled) 4. High-power dual-screen digital display, one-button charging, you will stop charging when you are fully charged. 5. This product is small and light, comes with a storage box, and the thread is not messy. 6. ABS insulated housing to prevent electric shock, shock, fall, and flame retardant. Specification: Name: Intelligent Battery Charger Fit For: 2-200AH lead-acid battery Color: black+orange Input: 110V-220V Output: 12V/24V Input Power: AC 200W Output Current: DC 10A 6A 3A Type Of Battery: lead-acid battery Size: 220*185*140mm/8.7*7.3*5.5in Note: 1. Please allow a bit error due to manual measurement. please make sure you do not mind before you bid. 2. The color may have different as the difference display, please understand. Package Included: 1 X Battery Charger (Distribute the adapter according to the country of order) Click here for more deals 12V/24V 2-200ah Intelligent Pulse Repair Battery Charger Lead-acid For Motorcyc 12V/24V 2-200ah Intelligent Pulse Repair Battery Charger Lead-acid For Motorcyc