24v waterproof lcd lithium

Buy FOXSUR 12V 24V 11-Stage LCD Display Battery Charger Waterproof Truck Car Motorc for R1,410.60

Buy FOXSUR 12V 24V 11-Stage LCD Display Battery Charger Waterproof Truck Car Motorcycl... (PLUG: EUPLUG) for R1,197.00

24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For Package weight: 0.41 kg Description: 1. Moto controller and LCD display adapts waterproof design, you can use it Conveniently at your daily time. 2. LCD display can clearly show the state and data, backlight enables you to see screen clearly in dim environment, buttons for quick operation, easy to use. 3. Brushless type of controller, working silently and sensitive to the state of electric bike. 4.LCD display comes with mount,suitable for 22mm handlebar. 5. Suitable for electric bicycles, cars, scooters. 6. Easy to install and use, comes with mount for LCD display and suitable for 22mm handlebar. 7. Fit for different battery: lead-acid, Li-Fe battery, LNCMO battery {Li(NiCoMn)O2}, and so on. For different material there is different under voltage protecting point. 8. Fit for DC brushless gear motor lower than 350w, and gearless motor, and high speed motor and so on 9.Suitable for: 250W/350W brushless DC motor (include with hall sensor and without hall sensor) Specification: Brushless Motor Controller: Voltage:DC 24V/36V/48V/60V Power:250W/350W Low volts:DC 19V/30V/41V/52V Max current available: 10A-20A (default setting 13A) 60° / 120° (Automatically indentify) Operating Conditions: -40￢ﾄﾃ ~80￢ﾄﾃ Material: Plastic + Metal Controller Function: 1. 1:1 pas power 2. Brake and cut off power 3. Connect with lcd display 4. Throttle 5. Horn/light power port 6. Self learning 7. Hall linear ebs brake 8. Cruise 9. 6km/h boosting Controller Feature: 1. Automatically indentify motor phase and angle 2. Dual mode (When motor hall work normally, controller work with hall mode. When motor hall damaged, controller can intelligently test it and change to no-hall mode and keep on work. (other controller if not double mode, cannot work if motor hall damaged) 3. Can control and match with other electric parts 4. When battery voltage is not enough the controller will automatically lower current, this will protect your battery for longer life. LCD Display: Brief introduction to 6 mosfet controller dual mode type for lithium battery Rated working voltage: 24V/36V/48V/60V Power available:250W/350W Max current available: 10A-20A (default setting 13A) Battery Voltage Undervoltage Protection Point: DC 19V/30V/41V/52V LCD Display Function: Battery indicator, Motor power indicator, speed stage, bike speed indicator, single trip distance, total trip distance, single trip time, battery detailed voltage, cruise control, assis control. 1. Adjust the brightness of backlight 2. Unit Changing, kilometer to mile, or mile to kilometer 3. Automatically indentify the voltage of battery 4. Sleep Time and Time Display Setting 5. Gear Setting 6. Accurate speed parameters 7. Limit the speed, speeding will brake 8. Start Mode Setting 9.Drive Mode Setting 10.Adjust the boost sensitivity 11. Change the strength and weakness of boost 12. Compatible magnetic points 13. Current and low voltage of controller setting 14. Total mileage accumulation and clearing 15. Cruise 16. Power-on password setting 17. 6km/h boosting and boosting at current speed LCD Display Error Code: 002 brake error 003 pas sensor error 004 boosting, 6km/h cruise mode 005 timely cruise mode 006 battery level low 007 motor error 008 throttle error 009 controller error 010 communication receive error 011 c Click here for more deals 24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For 24V/36V/48/60V 250W/350W Brushless Controller Battery Speed LCD Instrument For

AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display Package weight: 1.25 kg Description: Safety efficient,energy saving Technology of pulse width modulation Intelligent pulse repair type Manual adjustment or full automatic charger optional Automatic identification of 12V or 24V Compatible with lithium battery Specification: Wattage: 400W Input voltage:AC110-250V 50HZ-60HZ Full conversion rate:90%±3 Working temperature range:-30￢ﾄﾃ+40￢ﾄﾃ Rated voltage:12V/24V Constant current:18A±10% Charging current:10A±10% Constant voltage:14V±0.3 Charging voltage:28V±0.3 Size:21*16*8.7cm DC output line:60cm Power input line:130cm Package Included: 1 X Battery Charger 1 X User Manual Click here for more deals AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display AC110V-250V to 12V/24V Automatic Motorcycle Battery Power Charger LCD Display

30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD Package weight: 0.22 kg Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:30A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 X 10A PWM Solar Charge Controller 1 X Screwdriver 1 X Manual Click here for more deals 30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD 30A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD

10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD Package weight: 0.21 kg Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:10A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 x 10A PWM Solar Charge Controller 1 x Screwdriver 1 x Manual Click here for more deals 10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD 10A 12V/24V Solar Panel Battery Regulator Charging Controller 3-Stage PWM LCD

12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter Package weight: 0.02 kg Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable Click here for more deals 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter 12V 6-63V LCD Acid Lead Lithium Battery Capacity Indicator Digital Voltmeter

Specification: Name:10A 12V/24V LCD Display PWM Solar Panel Charge Controller Rated voltage:12/24V AUTO Charge current:20A Discharge current:10A Max.PV input power:130W(12V),260W(24V) Max solar input: 12V battery,the highest 23V 24V battery when the highest 46V Equalization Ternary lithium battery(L1):12.0V Lithium iron phosphate battery(L2):13.8V Lead acid battery:13.7V Undervoltage protection Ternary lithium battery:10V(Adjustable range: 9.0-11.0V) Lithium iron phosphate battery:12V(Adjustable range:10.3-12.8V) Lead acid battery:10.7V (Adjustable range:9.5-11.5V) Disstarge reconnect: Ternary lithium battery:11.6V(Adjustable range:11.0-11.7V) Lithium iron phosphate battery:13.5V(Adjustable range:12.8-13.8V) Lead acid battery:12.6V (Adjustable range:11.5-13.0V) USB output:2 way USB output,5V/2A(Max.) Self-consume: Operationg temperature:-35-60￢ﾄﾃ Color:Black Size:133mmx70mmx33mm Features: Build-in industrial micro controller. Big LCD display,all adjustable parameter. Fully 3-stage PWM charge management. Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection. Dual mosfet reverse current protection,low heat production. There are lithium battery and lead-acid battery switching function (at the battery type interface,3second into the switch settings),the default is lithium battery. System Connection: 1.Connect he battery to the charge regulator-plus and minus. 2.Connect the photovoltaic module to the regulator-plus and minus. 3.Connect the consumer to the charge regulator-plus and minus. Package Included: 1 X 10A PWM Solar Charge Controller 1 X Screwdriver 1 X Manual

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X 12V Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm   Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds   Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid   Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals)   Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

Specification: Display: Power, Voltage, Close, the key for cycle. Voltage Range: 6-63V, products will display based on the voltage value, voltage fluctuations, power meter will be follow as the voltage fluctuation! (Comes with reverse polarity protection, can be guarantee use effectively) The product is suitable for lead-acid 12V, 24V, 36V, 48V (can be changes via key, specific please see setup instructions as below) The product is suitable for 3.7V lithium series multi-platform, 3 string, 4 string, 5 string, 6 string, 7 string and 8 string 9 string 10 string 11 string 12 string 13 string 14 string 15 string (can be changes via key, detail information please see as below) Cable Length: 30cm Instructions: 1. Press and hold switch on the product, power on, automatically select the interface (please follow as the code corresponds blow) 2. Select your battery type after corresponding, for example 3 series lithium battery, you need to enter the selection screen, press the key point to for L3 interface, then off, re-energized, choose success, such as the need to set 12V lead-acid batteries, the key point press to P12V interface, power, re-energized, both choose success 3. instruments can be used if you Select successful. Meter shows the power interface, tap switch, switch to voltage interface, click the switch, turn off the meter. cycle shown as the code corresponds Fitment: Code: Suitable for For L3: 3 string lithium L4: 4 string lithium L5: 5 string lithium L6: 6 string lithium L7: 7 string lithium L8: 8 string lithium L9: 9 string lithium L10: 10 string lithium L11: 11 string lithium L12: 12 string lithium L13: 13 string lithium L14: 14 string lithium P12V: 12V lead-acid P24V: 24V lead-acid P36V: 36V lead-acid P48V: 48V lead-acid Note: Special Function Setting (requires electric iron, you must power off setting, electric iron must be grounded) A point connection, the backlight will be automatically shut down if delay10 seconds, the voltage fluctuation will automatic wake-up exceeds 0.3V / 0.5 seconds. B point connection, lithium choose 3-4.1V curve (lithium professionals) Package Included: 1 X Battery Capacity&Volt Tester 1 X Cable

12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle Package weight: 0.64 kg Description - Microprocessor Control (CPU) - 3-STAGE AUTOMATIC CHARGING: - Automatic charging protects your battery from being overcharged. So you can leave the charger connected to the battery indefinitely. - Suitable for most battery types including Calcium, Gel and AGM, Wet batteries. They may also help restore drained and sulphated batteries. -Types of batteries: Most types of lead acid batteries including Calcium, GEL and AGM, Wet,EFB, etc.. - Switchmode technology - Polarity protection - Output short protection - Non battery link protection - Over voltage protection - Over temperature protection Specification: Input voltage: 100V-265V AC, 50-60Hz Rated output: 12V 8A / 24V 4A Color: Red Minimum start voltage: 2.0V Battery range: 2Ah-150Ah Thermal protect: 65'C+/-5'C Efficiency: App. 85% Output Line Length: 65cm Input Wire Length: 110cm Compliant standards: CB,CE, IEC60335, EN61000, EN55014 Dimension (L×W×H): 170×98×58mm Cooling: Fan Scope of application: 12V/24V 2Ah-150Ah lead-acid batteries/start-up and shutdown batteries(lithium batteries can not be charged.) Note: This Charger is for battery capacity between 2AH to 150AH Pls check the capacity (AH) of your battery before buying the charger! Thanks! Package Included: 1 X 12V/24V Pulse Repair LCD Batteru Charger Click here for more deals 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle 12V/24V 8A Touch Screen Pulse Repair LCD Battery Charger Red For Car Motorcycle

12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD Package weight: 0.93 kg Description: LCD display at a glance Intelligent heat radiation, long service life Square lamp, safe and reliable, more convenient to operate Portable and durable, lightweight, easy to carry Advanced pulse width modulation (PWM)technology is used to automatically charge batteries through a 4-stage charging cycle The battery life can be significantly improved by digital pulse repairing method for the power chips of microcomputers Automatic Mode Advantages: When using automatic mode directly connected to the power supply and the battery on it, the charge without artificial regulation, the current will be fully automatic adjustment according to the battery needs to charge to a voltage location and automatic shutdown, the use of smart and convenient. Manual mode advantages: When the old battery is encountered, the ambient temperature is relatively low (below 0 °), and the battery capacity is slightly smaller, because of the large internal resistance of this type of battery, the trickle charging of small current occurs when using the automatic mode. Manual charging mode is aimed at such a large battery resistance characteristics of the design of the charging process, there are auxiliary repair battery function, the battery effect to play better. However, the use of manual mode charging must be artificially monitored, the battery case has a slight temperature, stop charging. Highly recommended: winter in the 0 ° below the environment, the battery to play a good time with the automatic mode is full, then manual mode, more than half an hour to 1 hour to make the battery performance better -Automatic charging mode: 12V battery charging, full voltage 13.8V-14.3V; manual charging mode: the maximum voltage of about 16V. The actual output current of 12V battery charging about 10A, 24V battery charging actual output current of about 7.5A The actual current depends on the demand for battery constant current constant voltage charging When the charge is completed, it will stop automatically at constant pressure, convert to trickle float mode, the constant current is about 0.2A The following is about the intelligent charger 12V battery reference charging time: (Actual charging completion time, the actual capacity of the battery may be) 6AH battery ~ 1-3 hours,7AH battery ~ 2--4 hours 9AH battery ~ 3 - 5 hours,10AH battery ~ 4 - 6 hours 20AH battery ~ 5--8 hours,32AH battery ~ 6 - 10 hours 36AH battery ~ 8-11 hours,45AH battery ~ 9-13 hours 55AH battery ~ 11--16 hours,60AH battery ~ 13--18 hours 80AH battery ~ 15--20 hours,105AH battery ~ 16--25 hours 120AH battery above, then analogize Specification: Material: Metal Input Voltage: 130V-250V Output Voltage: 12V-12A 24V-10A Power: 220W Frequency: 50-60HZ Name: Battery Charger Battery Type: Lead-acid battery Size: 15*19*7cm Power Cord Length: 120cm Weight: 750g Charging range: For the market 12v, 24v, 6AH-200AH of various types of batteries (except lithium iron battery) Packaged Included: Click here for more deals 12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD 12V/24V 200AH Electric Auto Car Battery Charger Intellective Sphygmus Repair LCD

Buy HTRC 12V/24V 10A/5A 7-Stage Touch Screen Pulse Repair LCD Battery Charger For Lithium for R700.91

Buy 12V/24V 25A 6-400Ah 600W High-power Pulse Repair LCD Battery Charger For Car Motorcycle Lithium Lead for R1,940.00