20pcs a4988 driver

Buy 20pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R449.05

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 3 x CNC Shield + UNO R3 Board + 4x A4988 Driver Kit

Buy 30pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R864.40

Buy 10pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink... for R299.00

Buy 5pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R266.26

Buy 10pcs A4988 Driver Module Stepper Motor Driver Board with Heatsink for R351.35

Buy 20pcs 1/4 Inch Hex Shank Drill Screwdriver Bit Driver Swivel Head Quick Change for R388.79

Buy 20pcs 4W 5W 6W 4-6W LED Driver Input AC 85-265V to DC 12V-24V Built-in Drive Power for R452.40

Buy 20pcs Dual Channel L298N DC Motor Driver Board PWM Speed Dual H Bridge Stepper for R656.82

Buy 20pcs ULN2003 Stepper Motor Driver Board Module for 5V 4-phase 5 line 28BYJ-48 Motor for R344.71

Buy 20pcs CJMCU-1308 TDA1308 Class AB Audio Module Stereo Headphone Driver Low Power Board for R690.46

Buy 20Pcs L293D L293 L293B DIP SOP Push Pull Four Channel Motor Driver IC... for R339.00

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: It is a self-drilling card holder for easy insertion and removal of the card. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 20 x Micro SD TF card module

Buy cnc shield v3 engraving machine 3D Printer board 4pcs A4988 driver expansion board for Arduino UNO for R482.88