10pcs 5v
Top sales list 10pcs 5v
South Africa
10Pcs 5V 16M ATmega328P Arduino Compatible Version LilyPad 328 Main Board Description: The Arduino Compatible LilyPad is a microcontroller board designed for wearables and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The board is based on the ATmega328 with the Arduino bootloader. The main board has a minimum number of external components to keep it as small (and as simple) as possible. The latest version supports automatic reset for even easier programming. The back side of the LilyPad is completely flat. It uses a surface mount programming connector, which keep the header from poking through. Specification: Microcontroller: ATmega328P Operating voltage: 2.7V ~ 5.5V (recommended 5V) Input voltage: 2.7V ~ 5.5V (recommended 5V) Digital I/O pins: 14 (of which 6 provide PWM output) Analog input pins: 6 DC current per I/O pin: 40mA Flash memory: 16KB (of which 2KB used by bootloader) SRAM: 1KB EEPROM: 512bytes Clock speed: 16MHz Note: Don't power the LilyPad Arduino with more than 5.5V, or plug the power in backwards: you'll kill it. Package included: 10 x Arduino compatible LilyPad ATmega328P
R 632
See product
South Africa (All cities)
10Pcs 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module Feature: Input voltage: AC 85 ~ 265v 50 / 60HZ or DC100v-370v Output voltage: DC5V (± 0.2V) Output Current: 700mA Power: 3.5W Package included: 10 x 5V 700mA 3.5W AC-DC Step Down Isolated Switching Power Supply Module
R 330
See product
South Africa (All cities)
10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load: AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module
R 346
See product
South Africa (All cities)
Buy 10pcs 5V 1A DC5521 Interface DC Charging Line Solar Panel Parallel Electronic C for R357.27
R 357
See product
South Africa (All cities)
Buy 10pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with Shell for R1,393.90
R 1.393
See product
South Africa (All cities)
Buy 10pcs 5V Low Level Trigger One 1 Channel Relay Module Interface Board Shield DC for R276.85
R 276
See product
South Africa (All cities)
Buy 10pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with for R1,778.47
R 1.778
See product
South Africa (All cities)
Buy 10PCS 5V Electric Magnetic Active Buzzer Continuous Beep Continuously 9*11.8mm ABS Black... for R209.00
R 209
See product
South Africa (All cities)
Buy 10pcs 5V PAM8403 3W*2 Dual Channel Audio Amplifier Module Class D Power Volume for R531.07
R 531
See product
South Africa (All cities)
Buy 10Pcs 5V Relay Module 5-12V TTL Signal 1 Channel High Level Expansion Board for R299.00
R 299
See product
South Africa (All cities)
Buy 10pcs 5V Lithium Battery Charger Step Up Protection Board Boost Power Module Micro USB Li-Po Li-ion for R502.00
R 502
See product
South Africa (All cities)
Buy 10Pcs 5V 30A ACS712 Ranging Current Sensor Module Board Geekcreit for Arduino - products that work w for R519.00
R 519
See product
South Africa (All cities)
Features: Automatic identification for iPhone and other smartphone 5V constant voltage output Automatic restart (after the sun weaker, stop charging, automatic recovery after discharge to strong sunlight) Compatible with most smart phones, tablet, for iPad, digital cameras, etc. Specification: Input voltage:6V-20V Output voltage: 5V Maximum output current: 2000mA conversion efficiency:95% Product size: 35x40x15mm Package Includes: 10 x Solar Panel Module
R 282
See product
South Africa (All cities)
Description: This Power Source For The Isolation Industrial-grade Built-in Power Supply Module, Temperature Protection, And Short Circuit Protection, AC85 - 265V Input Voltage, Wide 431 Precision Voltage Stability DC5V Output, With Mounting Holes, With Input And Output EMI Filter circuit Feature: Size: 5.1 x 2.4 x 2.0cm (L x W x H) Working Temperature: -20 - 60℃ Relative Humidity: 40 - 90%RH Input Voltage Range: 85- 265V Input Current: 0.054A(AC110V) 0.027A(AC220V) Input Inrush Current: 20A Output Voltage Range: 4.80-5.2V 0-1000mA Output Power: 0 - 5.5 W Output Efficiency: 80% Input Voltage of AC 85 - 265v 50/60 HZ Output Voltage DC5V (±0.2V) Output Current 1000MA Power: 5W Note: The End of the Step Down Module Can Be Conductive, Do Not Touch The Bottom of Template when you Test or to Use, Need Mattress Insulator Pad, Clean Cardboard Conductive things, Avoid Power Board contact to conductive objects such as Wire, so as to Avoid Electric Shock And Burn Out The Power Supply Board Package included: 10 x 5V 1A AC-DC Power Supply Step Down Module Bare board
R 525
See product
South Africa
10Pcs MB102 Breadboard Module Adapter Shield 3.3V/5V For Arduino Board Description: Breadboard power supply module, compatible with 5 V, 3.3 V Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient external lead use. Size: 5.3*3.2*2.5cm Weight: 12g Please notice: this item only a Power Supply Module, Breadboard is not included. Package included: 10 x Power supply module Breadboard power supply module, compatible with 5 V, 3.3 V.
R 229
See product
South Africa
10Pcs DC 5V 4 Phase 5 Wire Stepper Motor With ULN2003 Driver Board Description: This is 28YBJ-48 DC 5V 4 phase 5 wire stepper motor with ULN2003 driver board 5-wire phase can drive ordinary uln2003 chip can also be connected as phase 2 may be supporting the development board, direct plug, easy to use stepper motor used in the development board Motor: Diameter: 28mm Voltage: 5V Step angle: 5.625 x 1/64 Reduction ratio: 1/64 ULN2003 driver board: A, B, C, D LED indication Four-phase stepper motor work status Size: 31mm x 35mm Package included: 10 x ULN2003 driver board 10 x 28BYJ-48 stepper motor
R 504
See product
South Africa (All cities)
10Pcs DC-DC 12V to 3.3V/5V/12V Voltage Converter Power Supply Module Feature:One channel input: DC 6V - 12V (the input voltage must be higher than the output voltage to 1V or more.)Triple output: 3.3V (ﾱ 0.05v error), 5V (ﾱ 0.05v error), 800mA (load current can not exceed 800ma), 12V (12V input directly to the output)Specially designed two rows of needle fixing hole, can be directly fixing on the plate to extend the experiment;Using multiple input and output pin, easy to use and connect;PCB board size: 4.5 x 4.5cmWith power indicator (red)Package includes:10 x Multi-output Power Supply Module
R 310
See product
South Africa
10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module
See product
South Africa (All cities)
10pcs DC 5V DIY Electronic Windmill Training Kit Speed Adjustable MCU Course Design For Soldering
R 670
See product
South Africa (All cities)
10Pcs Geekcreit DC 5V 3MM x 10MM WS2812B SMD LED Board Built-in IC-WS2812
R 170
See product
South Africa (All cities)
10PCS Mini 0.5V 100mA DIY Polycrystalline Silicon Solar Panel
R 260
See product
South Africa (All cities)
10pcs BESTEP 1 Channel 5v Relay Module High And Low Level Trigger For Arduino Package contains 1 X item of the smallest listed variant.
R 440
See product
South Africa (All cities)
10Pcs ATMEGA328 328p 5V 16MHz Arduino Compatible Nano Size Module Board Package contains 1 X item of the smallest listed variant.
R 900
See product
South Africa (All cities)
10Pcs DS18B20 DC 5V Digital Temperature Sensor Module For Arduino Features: It's easy to install with mounting holes, diameter of the hole is 2.5m. Digital signal output 18B20 Temperature Sensor Chip Resolution adjustment ranges from 9-12 bytes. Operating current: DC5V. Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C. Size: 28 x 12 x 10 mm Weight: 2g Package included: 10 x DS18B20 digital temperature sensor module
R 378
See product
South Africa (All cities)
10Pcs HY-SRF05 Ultrasonic Distance Sensor Module Measuring Sensor Module Description: This module performance is stable, measure the distance accurately. Module precision, blind spots (2cm) super close. Specification: Input voltage: 5V DC Quiescent current: Output level(high): 5V Output level(low): 0V Induction angle: Detection distance: 2cm - 450cm Accuracy: up to 0.3cm Blind spots: 2cm Package included: 10 x HY-SRF05 ultrasonic distance sensor module
R 346
See product
South Africa (All cities)
10Pcs Mini 1A Lithium Battery Charging Module Board With USB Interface Description: Charging method: linear charge 1% Charging current: 1A adjustable Charge accuracy: 1.5% Input voltage: 4.5V-5.5V Full charge voltage: 4.2V Charging indicator: Red charging green full charge Charging input interface: Mini USB Working temperature: -10C to +85C Reverse: NO Size: 25 x 19 x 10mm Note: Ampere meter can only be connected to 5V input end of the module. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough. The connection wire should not be too long. Make sure the connect point is good. If the input voltage is too high, like 5.2V, the current will be less than 1000mA, it is normal. It is protection function, Auto-substract the charging current to avoid burn damage to chip. Input reverse has no effect on the chip, but the output (battery terminals) reverse will burn chips. Applications: This module is used for single-or multi-section parallel lithium lithium rechargeable battery, charging from the USB port to take power. Package included: 10 x 1A lithium battery charging module
R 288
See product
South Africa
10Pcs CJMCU 1 Bit WS2812 5050 RGB LED Driver Development Board Feature: Votalge: DC 5V Color: RGB Package included: 10 x 1 Bit WS2812 5050 RGB LED Driver Development Board
R 280
See product
South Africa
10Pcs Orinigal M27C322-100F1 DIP-42 Mbit 32M EPROMs EPROM Feature: Suitable for microprocessor systems requiring large data or program storage. It is organised as 2 M Words of 16 bit. The pin-out is compatible with a 32 Mbit Mask ROM. The FDIP42W has a transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be written rapidly to the device by following the programming procedure. For applications where the content is programmed only one time and erasure is not required. Specification: Power supply voltage: 5V ± 10% Programming voltage: 12V ± 0.25V Programming practice: 50μs / word Operation access time: 80ns Word width can be configured to 32 mbit mask rom replacement Stand-by current: 100μA Active current: 50mA at 5MHz Package includes: 10 x M27C322-100F1 DIP-42 Mbit EPROM
R 230
See product
South Africa (All cities)
10Pcs ATTINY85 Mini Usb MCU Development Board For Arduino Feature: 8K Byte of In-System Programmable Program Memory Flash 512 Bytes In-System Programmable EEPROM 512 Bytes Internal SRAM 1.8-5.5V work voltage Support SPI/TWI communication Low power consumption Package included: 10 x ATTINY85 Mini Usb MCU Development Board For Arduino
R 566
See product
South Africa (All cities)
10Pcs CJMCU-MCP4725 I2C DAC Breakout Development Board Module Description: You’ve always wanted to output analog voltages from a microcontroller, the MCP4725 is the DAC that will let you do it! The CJMCU-MCP4725 is an I2C controlled Digital-to-Analog converter (DAC). A DAC allows you to send analog signal, such as a sine wave, from a digital source, such as the I2C interface on the Arduino microcontroller. Digital to analog converters are great for sound generation, musical instruments, and many other creative projects! This version of the CJMCU-MCP4725 Breakout fixes a few issues with the board including the IC footprint, the I2C pinout, changes the overall board dimensions to better fit your projects, and a few more minor tweaks. This board breaks out each pin you will need to access and use the MCP4725 including GND and Signal OUT pins for connecting to an oscilloscope or any other device you need to hook up to the board. Also on board are SCL, SDA, VCC, and another GND for your basic I2C pinout. Additionally, if you are looking to have more than one MCP4725 on a bus, the pull-up resistors on this board can be disabled just check the Hookup Guide in the Documents section below for instructions and tips on doing this. Feature: 12-bit resolution I2C Interface (Standard, Fast, and High-Speed supported) Small package 2.7V to 5.5V supply Internal EEPROM to store settings Package included: 10 x CJMCU-MCP4725 I2C DAC Breakout Development Board Module
R 260
See product
-
Next →
Visit our blog
Share on Facebook
Share on Twitter