10pcs 5v low control

Buy 10pcs 5V Low Level Trigger One 1 Channel Relay Module Interface Board Shield DC for R276.85

Functional Description: MOS FET electronic switch module, you can use low-voltage and small current to control high-power equipment, motors, light bulbs, high-power LED. For example: you want a device output 5V signal, control a 12V motor switch. This module can be achieved. Feature: Input control voltage 3.3V-12V Output control voltage: 5-36V Board using optocoupler isolation, 2-terminal voltage completely separate. Input control using 2 pins to control, one connect ground one connect control to direct control the switch. Control current: 1-5MA control voltage is different, the current difference is mainly the loss in the LED. Charged current: 0-22A, if greater than 5A need to add heat sink. Board comes with LED indicator Controlled input and output with screw terminal block 2.54MM pin control terminal, is easy wiring. Control can be directly connected to the microcontroller IO. You can use the microcontroller ARDUINO PWM motor speed control, lamp brightness and so on. High current attention to add heat sink. Board size: 4 x 3 cm Package includes: 10 x MOS Field Effect Transistor Module

Functional Description:   MOS FET electronic switch module, you can use low-voltage and small current to control high-power equipment, motors, light bulbs, high-power LED. For example: you want a device output 5V signal, control a 12V motor switch. This module can be achieved.   Feature:   Input control voltage 3.3V-12V Output control voltage: 5-36V Board using optocoupler isolation, 2-terminal voltage completely separate. Input control using 2 pins to control, one connect ground one connect control to direct control the switch. Control current: 1-5MA control voltage is different, the current difference is mainly the loss in the LED. Charged current: 0-22A, if greater than 5A need to add heat sink. Board comes with LED indicator Controlled input and output with screw terminal block 2.54MM pin control terminal, is easy wiring. Control can be directly connected to the microcontroller IO. You can use the microcontroller ARDUINO PWM motor speed control, lamp brightness and so on. High current attention to add heat sink. Board size: 4 x 3 cm   Package includes:   5 x MOS Field Effect Transistor Module

Buy 10pcs Low Voltage MOSFET Switch Module Electronic 3V 5V Low Control High Voltag for R714.43

10Pcs 5V 1 Channel Level Trigger Optocoupler Relay Module For Arduino Description: The module uses genuine quality relay, normally open interfaces Using SMD optocoupler isolation, driving ability, stable performance The module can be high or low by a jumper setting trigger Fault-tolerant design, even if the control line is broken, the relay will not operate The power indicator (green), the relay status indicator (red) The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient Specification: Maximum load:  AC 250V/10A, DC 30V/10A Trigger current: 5mA Working voltage: 5V Module size: 50 x 26 x 18.5mm (L x W x H) Four mounting bolts holes, diameter 3.1mm Module interface: DC+: positive power supply (VCC) DC-: negative power supply (GND) IN: can be high or low level control relay Relay outputs: NO: normally open relay interface COM: Common Interface Relays NC: normally closed relay interface High and low level trigger options: It is low level trigger when jumper connect to LOW pin It is high level trigger when jumper connect to HIGH pin Package included: 10 x 1 Channel H/L level trigger optocoupler relay module  

Buy 10pcs 1 Channel 5V Relay Control Module Low Level Trigger Optocoupler Isolation for R288.99

Buy 10pcs 1 Channel 5V Relay Control Module Low Level Trigger Optocoupler Isolation for R317.41

Buy 10pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with Shell for R1,393.90

Buy 10pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board with for R1,778.47

Buy 5pcs 1 Channel 5V Relay Control Module Low Level Trigger Optocoupler Isolation for R256.00

5V 1 Channel Low Level Trigger Solid State Relay SSR for Arduino ARM DSP PIC with Resistive Fuse Input control signal voltage: 0V – 0.5V Low stage (SSR is OFF), 0.5V – 2.5V (unknown state). 2.5V – 20V High state (SSR is ON). SSR Output (each channel): Load voltage range:  75 to 264V AC (50/60Hz). Load current: 0.1A to 2A Power supply:  5VDC / 160mA all 8x channel ON. (20mA each) PCB thickness: 1.6mm. Size:  34 mm x 25 mm x 25 mm (L x W x H) SSR Specifications: Manufacturer: OMRON Part number: G3MB-202P, 5V version. Isolation: Phototriac. Zero cross: Yes. Rated output load: 2A at 100 to 240V AC.(50/60Hz). Pinouts Input section DC +: positive power supply (relay voltage power supply) DC-: connect power negative CH1: 1 signal to trigger the end of the relay module (low level trigger valid) Output Section A1: Relay Normally Open point A B1: Relay Common Power must be DC voltage, and voltage must be consistent with the relay voltage.     This item is available in stock and is not drop shipped. This avoids delays, customs charges and extra VAT.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 5V Omron solid state relays 240V / 2A, output with resistive fuse 240V / 2A. Dimensions: 25x34x25 (length x width x height) Input Power: 5VDC Control signal input voltage: (0-2.5V low state relay ON) (3-5V state high relay OFF) Feature: Voltage:5V Quiescent current: 0 mA Operating current: 12.5mA Trigger Voltage: 3.3-5V Trigger current: 2mA DC +: positive power supply (according to the relay voltage supply) DC-: negative power supply CH1: relay module signal triggering end (low to trigger active) Package included: 10 x One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino 10Pcs One way Solid State Relay Module For Arduino

Description:   For microcontrollers without an analog-to-digital converter or when you want a higher-precision ADC, the ADS1115 provides 16-bit precision at 860 samples/second over I2C. The chip can be configured as 4 single-ended input channels, or two differential channels. As a nice bonus, it even includes a programmable gain amplifier, up to x16, to help boost up smaller single/differential signals to the full range. We like this ADC because it can run from 2V to 5V power/logic, can measure a large range of signals and its super easy to use. It is a great general purpose 16 bit converter. The chip's fairly small so it comes on a breakout board with ferrites to keep the AVDD and AGND quiet. Interfacing is done via I2C. The address can be changed to one of four options (see the datasheet table 5) so you can have up to 4 ADS1115's connected on a single 2-wire I2C bus for 16 single ended inputs.   Feature:   Wide supply range: 2.0V to 5.5V Low current consumption: Continuous Mode: Only 150uA Single-Shot Mode: Auto Shut-Down Programmable data rate: 8SPS to 860SPS Internal Low-drift voltage reference Internal oscillator Internal PGA I2C interface: Pin-Selectable Addresses Four Single-ended or two differential inputs Programmable comparator This board/chip uses I2C 7-bit addresses between 0x48-0x4B, selectable with jumpers Package included: 10 x I2C ADS1115 16 Bit ADC 4 Channel Module

10pcs BESTEP 1 Channel 5v Relay Module High And Low Level Trigger For Arduino Package contains 1 X item of the smallest listed variant.

10Pcs Micro SD TF Card Memory Shield Module SPI Micro SD Adapter For Arduino Features: The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write Module features are as follows: Support Micro SD Card (The level conversion circuit board that can interface level is 5V or 3.3V Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board Communication interface is a standard SPI interface 4 M2 screw positioning holes for easy installation Size: 4.1 x 2.4cm Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal Micro SD card connector: Since the bomb deck for easy card insertion and removal. Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination Package included: 10 x Micro SD TF card module