Waveshare servo driver

Buy Waveshare Servo Driver HAT B Type with 16 Channel 12bit I2C Interface Right Angle Pinheader for Ras for R450.00

Buy Waveshare Servo Driver HAT B Type with 16 Channel 12bit I2C Interface R for R399.00

Buy 24-CHANNEL USB CONTROLLED SERVO DRIVER 62611 / 180695 for R934.39

Buy M5Stack Goplus2 DC Motor and Servo Driver Module STM32F0 IR Transmitter and Rec for R732.64

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Introduction: The IMX179-based USB camera module, 8 megapixels, has an image resolution of up to 3288x2512. Support UVC protocol, drive-free, ready to use. Parameter: Image: 8 million Resolution: 3288x2512 Photosensitive chip: IMX179 DSP: Automatic white balance Automatic exposure Automatic gain Camera: CCD size: 1/3.2 inch Aperture (F): 1.8 Focal Length: 2.8mm Diagonal angle: 145° Microphone parameters: Sensitivity: -26dB (1kHz 1Pa) Interface type: USB2.0 Supported image formats: MJPEG, YUY2 Working temperature: 0 ° C ~ 50 ° C Product size: 38mmx38mm Support system: Windows, Linux Package includes: 1 x IMX179 8MP USB Camera (A) 1 x USB to 4Pin line Waveshare IMX179 USB Camera Module 8 Megapixel 3288x2512 Built-in Microphone Free Driver Waveshare IMX179 USB Camera Module 8 Megapixel 3288x2512 Built-in Microphone Free Driver Waveshare IMX179 USB Camera Module 8 Megapixel 3288x2512 Built-in Microphone Free Driver

Buy Waveshare 2.7 Inch Bare e-Paper Screen + Driver Board Onboard ESP8266 Module Wi for R979.52

Buy Waveshare 2.7 Inch Bare e-Paper Screen + Driver Board Onboard ESP8266 Module Wireless for R955.20

Buy Waveshare 2.13 Inch Bare e-Paper Screen + Driver Board Onboard ESP8266 M for R669.00

Buy Waveshare e-ink Display Screen Driver Board SPI Interface Compatible for R354.38

Buy Waveshare 3.2 Inch Color Touch Display TFT LCD 320x240 Resolution Module Board ILI9325 Driver for R607.72

Buy Waveshare 3.2 Inch Color Touch Display TFT LCD 320x240 Resolution Module Board ILI9325 Driver for R551.00

FULL BRIDGE MOTOR DRIVER FOR DC SERVO MOTORS AND GEAR MOTORS; 36V; 30A; PWM INPUT FOR SPEED CONTROL - 5V ARDUINO BOARD COMPATIBLE

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot

Mini USB 24 Channel Servo Motor Driver Controller Module For Arduino Robot Specification: 32-bit CPU Power of servo and control board are separate Chip Power Supply: 6.5V ~ 12V or 4.5V ~ 5.5V (one is for USB) Servo Power Supply: Generally DC 5V (base on the servo you use) Channel: 24 (servo speed adjustable) Communication Input: USB or Serial Port(TTL) Signal Output: PWM (accuracy 1us) Servo Motor Resolution: 1us, 0.045 degrees Baud Rate: 9600, 19200, 28400, 57600, 115200, 128000 (recognized automatically) Dimensions: 51.0 x 43.5 x 1.6mm Control Mode: USB and UART (TTL) Flash Memory: 512K ROM Package included: 1 x 24 Channel USB Servo Motor Driver Controller Module

Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot