Variety board

SIM808 GSM GPRS GPS BT Development Board Module For Arduino Description: SIM808 a new generation of GSM, GPRS, GPS, bluetooth (optional) SIM808 GSM GPRS module is a four frequency for the castle hole encapsulation. Its performance is stable, compact appearance, high cost performance, which can meet the various needs of customers. SIM808: SIM808 working frequency for GSM/GPRS / 1800/1900 850/900 MHZ, can realize low-power transmission of voice, SMS and data information. Features: The four frequency MHZ 850/900/850/900 SMS FTP/HTTP, embedded TCP/UDP protocol DTMF detection, bluetooth 3.0 (optional), USB interface Arduino SIM808 shields hardware: Power interface support 5-20V voltage input, pay attention to the voltage of 5-9V, can provide not less than 2 a power adapter current. 1. Can choose to use through the jumper cap hardware serial port (D0 D1) or software serial port (D7 D8). 2. Support the MICRO SIMCARD. 3. Support four headphone jack (I type). 4. Update SIM800C firmware support via USB or serial port. 5. Can be upgraded to a bluetooth version of the development board. 6. On board TVS diode, SIM card protection IC, two 100 uf tantalum capacitors and so on a variety of ways to make the stable development board performance. 7. Support the lithium battery (3.6-4.2 V) For TTL level serial communication interface. Fully compatible with the Arduino and compatible with other 5 V, 3.3 V, 2.85 V system. Arduino SIM808 shields software: By TTL level a serial port communication with external systems, the default is communicated with 5 v system directly. Communicated 3.3 V and 2.85 V, it needs to do a bit of hardware processing. Communication interface (command) for the AT command, which is control module function to realize the AT command, such as: control module to make calls using ATD * * * * * * *; (* phone number) for each other. Package included: 1 x SIM808 GSM GPRS GPS BT Development Board Module For Arduino

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features Can play a variety of music formats, support for OGG encoding real-time recording SPI interface, the control signal lines are led out A headphone and stereo output A microphone for recording A line_in input interface Power indicator 3.3V and 2.8V of LDO chip AMS-1117 on board, provides up to 800mA current A single power supply: +5 VDC 12.288 MHz crystal TF card slot Package included: 1 x MP3 Music VS1053B Shield Board With TF Card Slot MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA MP3 Music VS1053B Shield Board With TF Card Slot Work With Arduino UNO MEGA

Features: 1. Black plate-making process, beautiful, high-quality 2. Configure the STM32 chip, LQFP48 package, 72M frequency, 64K-FLASH, 20K-RAM 3. With power indicator, onboard programmable LED lights 4. The board has 8M crystal, ST recommended brand RTC Crystal 5. Standard 20P-JTAG / SWD interface that used for a variety of common emulator 6. The board has 24C04- data parameter memory for easy application development, data access parameters 7. All GPIO independent leads, pin can be up and down welding, soldering default down 8. Size: 41.7 x 53.9 mm Package included: 5 x Stm32f103c8t6 development board

Description:   ESP32 is already integrated antenna and RF balun, power amplifier, low-noise amplifiers, filters,  and power management module. The entire solution takes up the least amount of printed circuit board area. This board is used with 2.4 GHz dual-mode Wi-Fi and Bluetooth chips by TSMC 40nm low power technology, power and RF properties best, which is safe, reliable, and scalable to a variety of applications.   Features:   High performance-price ratio Small volume, easily embeded to other products Strong function with support LWIP protocol, Freertos Supporting three modes: AP, STA, and AP+STA Supporting Lua program, easily to develop Development Board:  Package included: 1 x ESP32 Development Board(unsoldered)      

Funduino Nano Expansion Board + ATmega328P Nano V3 Improved Version For Arduino Description: Funduino Nano Expansion Board This Nano Mult-Function expansion board is designed specially for Arduino Nano, solve the problem of wiring confusing when a variety of sensors connected. Lead out all digital IO port and analog IO port, each one with standard positive and negative power interface. Lead out the I2C interface of mainboard for convenient connection. Increasing the DC power supply interface. Nano USB interface supply current is actually only 50MA, to bring high-current devices, such as the steering, is obviously insufficient. So in the DC power connector provide external power supply to ensure the stability of equipment operation. ATmega328P Nano V3 Improved Version Microcontroller Atmel ATmega328 Operating Voltage (logic level): 5V Input Voltage (recommended): 7V ~ 12V Input Voltage (limits): 6V ~ 20 V Digital I/O Pins: 14 (of which 6 provide PWM output) Analog Input Pins: 8 DC Current per I/O Pin: 40mA Flash Memory: 32KB (ATmega328) (of which 2 KB used by bootloader) SRAM: 2KB (ATmega328) EEPROM: 1KB (ATmega328) Clock Speed: 16MHz Note: This version is not included the USB cable. Had change the USB chip, improve the download speed and stability of WIN7/WIN8 Package included: 1 x Funduino Nano Expansion Board 1 x Arduino Compatible Improved Version Nano V3.0  

Description: Large output power, energy sufficient, good quality, can directly drive 4 Ω or 8 Ω small speakers Good noise suppression you will hear nothing from the loudspeaker if there is no audio input Your can charge this board directly with your computer or mobile phone USB Super mini design can be easily placed in a variety of digital products The whole board adopts machine welding with high quality stand The eft and right channels output end cannot connect together! Specifications: Unit size: 1.85 x 2.11cm Material: FR4 Input Voltage: 2.5 - 5V USB power supply is available Package included: 20 x 3W D-Type PAM8403 amplifier board

TB6560 3A CNC Router 1 Axis Driver Board Stepper Motor Drivers   is available now from our US   warehouse Free shipping to US  in 3-6 business days ship to Canada, Brazil in 7-10 days TB6560 3A CNC Router 1 Axis Driver Board Stepper Motor Drivers Specification: Size: 75 x 50 x 35mm / 2.95 x 1.96 x 1.37inch (L x W x H) Rated maximum output: ± 3A, peak 3.5A Working voltage: DC 10V-35V Recommended to use a switching power supply: DC24V power supply Subdivision: whole step, half-step, step 1/8, 1/16 step, a maximum of 16 Subdivisions. Feature: Using the Toshiba TB6560AHQ new original chip with low voltage shutdown, overheating stop and over current protection circuit to ensure optimal performance. For two-phase within 42, 57 stepping 3A / four-phase / of line four / six-wire stepper motor, and is not suitable for more than 3A stepper motor. Automatic half current function. 6N137 high-speed optical coupling, guarantee high speed without losing step. Features similar products: 1. Current grade-by-adjustable to meet your demand for a variety of applications. 2. Semi-automatic flow adjustable. 3. 6N137 high-speed optical coupling, guarantee high speed without losing step. 4. Plate printed setup instructions operation without manual also. 5. Thick teeth radiator, good heat dissipation. Package included: 1 x TB6560 1 axis driver board  

Description:   ESP32 integrates antenna switches, RF balun, power amplifiers, low noise amplifiers, filters and power management modules, and the entire solution occupies the least printed circuit board area. 2.4 GHz Wi-Fi plus Bluetooth dual-mode chip Using TSMC low-power 40nm technology, power performance and RF performance is the best, safe and reliable, easy to expand to a variety of applications. Use the documentation to download: https: //github.com/Nicholas3388/LuaNode User manual: https: //github.com/SmartArduino/SZDOITWiKi/wiki/ESP8266---ESP32   Feature:   Cost-effective small volume. Easy to embed into any product Powerful, support LWIP protocol, freertos Supports three modes: AP, STA, AP + STA coexistence mode Lua programming makes your development easier For more details click on the link: https: //github.com/espressif/arduino-esp32/blob/master/doc/windows.md Package included: 1 x WeMos® ESP32 WiFi + Bluetooth Development Board 2 x normal pin

Introduction:   CC3D flight controller board is an open source UAV flight control board, is easy installation. At the same time, it contains a variety of interfaces to support more remote control and equipment. The CC3D and Atom boards are the stable hardware for all the functions of the firmware that it runs in OpenPilot. It can fly any body from fixed wing to octocopter, and is configured and monitored with OpenPilot Ground Control Station (GCS) software.   Specification:   Size: 37 * 36 * 13mm Weight: 7.1g   Package includes:   1 x CC3D Flight Controller

Description:   This is a Colorful LED USB lamp, can work with a variety of modes:Always flashing, Colorful discoloration, White, Yellow, pink, ice blue, violet, red, green, blue.   Package included:   1 x Mini USB LED board

Description: LCD screen tester (Sixth Edition) using a new hardware-driven solutions and software programs, the new white-green word panel, screen printing clear and beautiful. Features: 1. Easy to use, the sixth edition built-in 55 kinds of LVDS LCD resolution program; 2. Through the button to switch the digital display corresponding to the resolution of the value, you can point screen; 3. Increase the LCD screen power supply short circuit protection, to prevent the screen line inserted into the dislocation or LCD screen power supply circuit board damage to the driver board, short circuit after the digital display screen display flashing "00", buzzer long ringing, short circuit removed to restore normal Prohibit more than ten minutes long short-circuit); 4. Built a variety of standard test chart, test chart function and the role of the following description; 5. Test panel comes with operating instructions, use at a glance; 6. With a key automatic baking machine mode, easy maintenance, factory assembled roasted machine; 7. Plug in the external VGA cable automatically switches to an external VGA input signal display; 8. Almost compatible with 95% of the 7-inch -84 inch LVDS interface LCD / LED LCD screen test; 9. General 12V LCD power supply, the current size of the screen according to the actual needs of the test; 10. To support the development of our eDP interface LCD screen adapter board to support a variety of resolution eDP interface LCD screen test. Specifications: Panel Tester voltage selction: 3V/ 5V / 12V 1/2/4 Lamps CCFL inverter. Input: 10V-30V Support: 10-22inches Power adapter: Input: 100-240V 50/60HZ Output: 12V 4A Tester size: 130 x 80 x18mm Inverter size: 120 X 40mm Power adapter size: 110 x 50 x 30mm How to use: LCD screen test support standard, high-definition full-resolution LVDS signal, built-in 12 test screen, convenient and practical. Screen switching: can switch cycle test tool built-in 12 kinds of test screen. Quality switch: according to the actual display screen effect, switch to the appropriate quality. Automatic switching: 12 kinds of test screen automatically cycle display. VGA input interface: insert the computer VGA signal, that is displayed on the LCD screen, the tester without any switch. VGA output interface: the tester can be 12 kinds of internal test screen signal through the VGA cable to another display, to determine whether the display does not light, the equivalent of a VGA signal source. Package included: 1 x LCD LED Panel Tester 14 x most common used Lvds screen cables 1 x High-voltage line 1 x CCFL backlight lamp inverter 1 x 12V AC power adapter (According to the delivery countries distribute adapter.) Detail Pictures:

The MM6 Music Synthesizer delivers all that power and more. Drawing on the same sounds of the popular pro-level MOTIF series instruments, the MM6 has a wide variety of dynamic, realistic and just plain powerful Voices to help you create amazing music. The MM6 also gives you total control over your sound, with real-time tweakable knobs, and features special Patterns that provide full backing - drums, bass and chords - for your live performance and song creation. And since the MM6 is exceptionally light and portable, you can bring it anywhere and everywhere your music takes you. The MM6 gives you: - Super-high-quality sounds - Tons of real-time control - Dynamic music creation tools-including automatic Pattern and Arpeggiator generators - Performance Memory for instantfull-panel setting changes - Versatile song recording features -with eight normal tracks and one Pattern track - Convenient, easy-to-use data storage solutions Features Power to Make You Move Tap into the Power to perform, Power to create, Power to make you move. The MM6 Music Synthesizer delivers all that power and more. Drawing on the same sounds of the popular pro-level MOTIF series instruments, the MM6 has a wide variety of dynamic, realistic and just plain powerful Voices to help you create amazing music. The MM6 also gives you total control over your sound, with real-time tweakable knobs, and features special Patterns that provide full backing—drums, bass and chords—for your live performance and song creation. And since the MM6 is exceptionally light and portable, you can bring it anywhere and everywhere your music takes you. The MM6 gives you: Super high quality sounds Tons of real-time control Dynamic music creation tools – Authentic Pattern and Apreggiator generators Performance Memory for instant full panel setting changes Versatile song recording features – with eight normal tracks and one Pattern track Convenient, easy to use data storage solutions Play Sounds from the Legendary MOTIF That's the first and most important thing you look – and listen – for in a synthesizer. Rest assured, this synthesizer delivers. The MM6 has 418 Voices and 22 Drum Kits on board, based on the sounds of the famed pro-level MOTIF series synthesizers. These exceptionally high-quality sounds range from authentic and natural acoustic instruments to wild, unique and in-your-face synth Voices. An extra set of GM Voices (128 Normal, 1 Drum Kit) is built into the instrument as well, giving you all you need to play back songs recorded in that popular format. So many Voices, so little time…That's why we've also included a convenient Category Search function. Just select the type of instrument you want to play—organ, guitar, synth lead, strings, whatever—then select the specific Voice. All your favorite sounds are right at your fingertips. The Power to Control Tweak - Your Sounds the way you want Take control. Twist some knobs and tweak the sound. Make it sing and make it scream. The MM6 puts some serious control in your hands. Change the filter cutoff and resonance settings as well as the EG attack and release with the four knobs – in real time as you play. Jam - Patterns to Groove on The MM6 has a full set of Patterns that give you rhythmic backing in a wide variety of music styles – including Hip Hop, Rap, R&B, Dance, Ambient, Pop, Rock, Jazz and even World styles. These Patterns are just what you need to shake up the dance floor. All dynamic, all powerful – the MM6 gives you the real thing. Patterns that stay in the groove, but never sound mechanical. Drum loops with a truly human feel that dance and float around the beat, yet remain firmly in the pocket. Riffs and licks that get you inspired, get you moving, and get you creating some serious music. Arpeggiate Yourself Generate some excitement. The powerful Arpeggiator feature lets you automatically create repeating rhythmic phrases and note patterns. A full 213 Arpeggiator types are built in, letting you trigger a variety of musically useful and exciting patterns to get the house jumping. Many of these Arpeggiator types use synth lead, piano and guitar Voices to generate melodic and broken chord patterns based on the chords you play with your left hand. Bass arpeggios and Drum Voice rhythm loops are also included, letting you easily set up dynamic riffs and beats to jam over. Create - Your Music, Your Way When you play live, you want to be able to make sound changes quickly – not just between songs, but in the middle of a song too. The Performance Memory feature is just the tool you need to smoothly switch gears and take things up a notch or two. Each Performance can store combined settings for the Voices you want to use (including special keyboard splits and layers), the Patterns you want as backing tracks, and any other crucial settings for your live work. Then, simply call up each Performance by pressing a single button. Save and Swap Share the wealth. With the rear panel USB connection, the MM6 makes it easier than ever before to transfer your valuable data between devices. Plug in a USB thumb drive or memory stick and store the important MIDI songs, Pattern files, Performance settings and all other data you've created, and then bring it to a computer for archiving and organizing. You can also save your recorded songs in the universal SMF (Standard MIDI File) format, then transfer and use those on any another SMF-compatible device, including computers running MIDI music sequencing software. Produce - Studio Smart, too The MM6 is all about making music. And since much of today's music is being made on computers, the MM6 is built to fit right into any computer music system. Just connect the USB To Host terminal on the instrument to your computer with a standard USB cable, and you've got the makings of a sophisticated recording setup. And just to make sure you get a head start, we've included a free copy of Cubase LE – a full-featured music production software that has all you need to record your performance data from the MM6 via MIDI (and even use plug-in synthesizers in the software), edit the data, process the sounds with effects, arrange it in multiple tracks and perform final mixdown.

Raindrops Detection sensor modue rain module weather module Humidity For Arduino is available now from our US and UK warehouse Free shipping to US and UK in 3-6 business days ship to Canada, Brazil in 7-10 days in US warehouse ship to European countries in 7-10 days in UK warehouse Snow Raindrops Humidity Rain Weather Detect Sensor Module For Arduino Description: The item is for Arduino robot kit, raindrops, rain sensor, monitoring can be used for a variety of weather conditions, and converted into the number of the reference signal and the AO output. The sensor uses the FR-04 high-quality double-sided materials, King Size 5.0 * 4.0CM, and with the surface of the nickel plating treatment, against oxidative, conductivity, superior performance and longevity; The output in the form: digital switching outputs (0 and 1) and analog AO voltage output; TTL-level output, TTL output valid signal is low. Driving capability 100MA so, can directly drive relays, buzzer, a small fan, and so on. Sensitivity can be adjusted via potentiometer LED lights up when there is no rain output is high, raindrop up, the output ground level, LED light. Feature: Distribution bit to adjust sensitivity A fixed bolt hole for easy installation Power indicator, the output signal LED indicator The comparator output, the signal is clean, waveform, driving ability over 15mA Wide voltage LM393 comparator A large area of ?ﾋ￢ﾀﾋrain board, more conducive to detect rain Board with positioning holes to facilitate installation Raindrops and control panels are separate, easy to wire leads Specification: Small board PCB size: 3.2cm x 1.4cm Operating voltage: 3.3V-5V Voltage: 5V How to use: Connected to 5V power supply, the power indicator light, sensor board is not water droplets, DO output is high, the switch lights off, dropping on a drop of water, DO output is low, the indicator light switch, Brush off the the above water droplets, has returned to output high state.... AO analog output can be connected to the microcontroller AD port to detect the size of the drops in the above rainfall. DO TTL digital outputs can also be connected to the microcontroller detects whether there is rain. Connection mode: 1, VCC: positive power supply (3-5V) 2, GND: negative one. 3, DO: TTL switching signal output 4, AO: Analog signal output Package included: 1 x Rain sensing board 1 x Control board 5 x 20cm Dupont Line '

POWER AND CONTROL. TWO ELEMENTS THAT CAN MAKE ALL THE DIFFERENCE... Power and control. Two elements that can make all the difference in your music, whether you compose, create or perform. The MM8 and MM6 Music Synthesizers deliver all the musical power and creative control you need - and a whole lot more. Taking their sounds from the highly popular pro-level MOTIF series instruments, the MM8 and MM6 have an enormous variety of dynamic, authentic Voices to help you create and perform in virtually any style of music. These powerful instruments also give you total control over your sound, letting you dynamically change sonic textures as you play with real-time tweakable knobs. Also built-in are special Patterns that provide full instrumental backing - drums, bass and chords - to accompany your live performance and song creation. With its exceptional light weight and portability, the MM6 is the perfect choice for musicians on the go, while the full length 88-key keyboard of the MM8 delivers natural touch and expressive control over the complete piano range. Super-high-quality sounds Tons of real-time control Dynamic music creation tools—including automatic Pattern and Arpeggiator generators Performance Memory for instantfull-panel setting changes Versatile song recording features —with eight normal tracks and one Pattern track Convenient, easy-to-use data storage solutions PLAYABILITY The MM8 and MM6 have 418 Voices and 22 Drum Kits on board, all based on the dynamic, realistic sounds of the advanced MOTIF series synthesizers. These exceptionally high-quality sounds range from authentic acoustic instruments to wild, unique and in-your-face synth Voices. An extra set of GM Voices is built into the instrument as well, giving you all you need to play back songs recorded in that popular format. With so many Voices to choose from, you might think it's difficult to select the ones you need. Not so. The convenient Category Search function lets you choose the type of instrument you want to play - organ, guitar, synth, lead, strings, whatever - then select the specific Voice. All your favorite sounds are right at your fingertips, ready to play when you are. Comprehensive Control The MM series is all about control. Take a look at some of the ways you can use it to power your performance and make your songs really stand out. Arpeggiator Madness Generate some excitement, and tap into even more inspiration while you play with the Arpeggio feature. This lets you automatically trigger repeating rhythmic phrases, riffs, broken chords and melodic patterns - and even change them harmonically by the notes or chords you play with your left hand. The MM8 and MM6 come with 213 different Arpeggio types built in, providing a variety of musically useful and exciting patterns to get the house jumping or to jump start your song writing. Bass arpeggios and Drum Voice rhythm loops are included as well for setting up dynamic riffs and beats to jam over. Arpeggio, Tweak Your Sound Once you've called up a synth Voice, you can simply play it as a static sound by pressing the keys - or you can take it another level up, and tweak the sound while you play with the four control knobs. Make it sing and weep or make it scream and holler. Change the filter cutoff and resonance settings for real-time texture shifts, and tweak the EG attack and release to completely alter the dynamic feel of the Voice as you play. Want some instant inspiration? The MM8 and MM6 have a full set of Patterns that give you powerful rhythmic backing in a wide variety of music styles - including Hip Hop, Rap, R&B, Dance, Ambient, Pop, Rock, Jazz and even World styles. These Patterns are just what you need to get your music moving in the right direction. What's more, these Patterns are as close to the real thing as you can get. Patterns that stay solidly in the groove, but never sound mechanical. Drum loops with a truly human feel that dance and float around the beat, yet remain firmly in the pocket. Riffs and licks that get you inspired, make you move, and help you create some serious music. Piano-like Expressiveness - Graded Hammer Keyboard Drawing on its long experience (over 100 years!) in crafting fine acoustic pianos, Yamaha has equipped the MM8 with a remarkably expressive GHS (Graded Hammer Standard) keyboard. If you're a piano player, you'll notice and appreciate the difference as soon as you touch the keys - the instrument feels and responds like a grand piano! The GHS keys are weighted heavier on the lower notes and gradually become lighter as you play up the keyboard, giving you detailed expressive control over the sound. GHS (Graded Hammer Standard) keyboard PERFORM AND CREATE Performance Memory When you play live, you want to be able to make sound changes quickly - not just between songs, but right in the middle as well. The Performance Memory feature is the perfect tool for doing this, letting you seamlessly switch gears in the middle of a performance (or recording) and take things up a notch, or bring the dynamics down instantly. Each Performance can store combined settings for the Voices you want to use (including keyboard splits and layers), the Patterns you'll use for backing, and any other crucial settings you may need - then select them simply by pressing a single button. Up to 64 Performances (eight banks of eight each) can be saved to the instrument, and you can save even more to USB memory stick. Song Creation and More The MM8 and MM6 are also ideal tools for song writing and demo making. The powerful, authentic sounds of the MM series as well as its dynamic Patterns and Arpeggios ensure that your tracks sound completely professional. Up to five User Songs can be recorded to the instrument, and with the built-in rear panel USB terminal, you can store up to 400 Songs to a USB memory stick or thumb drive. In fact, the USB connection lets you store Pattern files, Performance settings and all other important data you've created, and then bring it to a computer for archiving and organizing. Songs can also be saved in the universal SMF (Standard MIDI File) format for use on any SMF-compatible device, including DAW software At home or in the studio, the MM8 and MM6 can serve as the center of your music production system. Most of today's music is being made on computers and the MM series fits right into any computer music system. Just connect the USB To Host terminal on the instrument to your computer with a standard USB cable, and you've got a compact, yet full-featured recording setup. And just to make sure you get a head start, we've included a free copy of Cubase AI 4 - a sophisticated music production software that has all you need to record your performance data from the MM8 or MM6 via MIDI (and even use plug-in synthesizers in the software), edit the data, process the sounds with effects, arrange it in multiple tracks and perform final mixdown.

Description: The item is for Arduino robot kit, raindrops, rain sensor, monitoring can be used for a variety of weather conditions, and converted into the number of the reference signal and the AO output. The sensor uses the FR-04 high-quality double-sided materials, King Size 5.0 * 4.0CM, and with the surface of the nickel plating treatment, against oxidative, conductivity, superior performance and longevity; The output in the form: digital switching outputs (0 and 1) and analog AO voltage output; TTL-level output, TTL output valid signal is low. Driving capability 100MA so, can directly drive relays, buzzer, a small fan, and so on. Sensitivity can be adjusted via potentiometer LED lights up when there is no rain output is high, raindrop up, the output ground level, LED light. Feature: Distribution bit to adjust sensitivity A fixed bolt hole for easy installation Power indicator, the output signal LED indicator The comparator output, the signal is clean, waveform, driving ability over 15mA Wide voltage LM393 comparator A large area of ??rain board, more conducive to detect rain Board with positioning holes to facilitate installation Raindrops and control panels are separate, easy to wire leads Specification: Small board PCB size: 3.2cm x 1.4cm Operating voltage: 3.3V-5V Voltage: 5V How to use: Connected to 5V power supply, the power indicator light, sensor board is not water droplets, DO output is high, the switch lights off, dropping on a drop of water, DO output is low, the indicator light switch, Brush off the the above water droplets, has returned to output high state.... AO analog output can be connected to the microcontroller AD port to detect the size of the drops in the above rainfall. DO TTL digital outputs can also be connected to the microcontroller detects whether there is rain. Connection mode: 1, VCC: positive power supply (3-5V) 2, GND: negative one. 3, DO: TTL switching signal output 4, AO: Analog signal output Package included:

MKS-Gen L Overview: Aiming at the problems exist on the open sourced controller board such as Ramps 1.4, the developers in Makerbase specially optimize and develop a new product, MKS-Gen L, which provides more flexible choices for users. Features: 1. 2560 and Ramps 1.4 are integrated in the board, which avoids the complicated connectors. 2. Support a variety of stepper drivers such as A4988, DRV8825, TMC2100 and LV8729, available to change the stepper drivers and motors as users like. 3. Reserve external driver signal, available to connect external high-current driver to drive the 57 and 86 stepper motors. 4. Use high-quality MOSFET, better cooling and more stable. 5. Use specific power chip, support 12V-24V power input, and resolve the problems of chip heating and power shortage. 6. Stable and reliable filter circuit greatly reduces interference and avoids crashes as possible in the process of printing. 7. Use CH340 serial port chip, more easily install the drive than 16U2. 8. Run Marlin firmware, the configuration is completely same as Ramps 1.4, and available to directly replace the Ramps 1.4. 9. Support Ramps 1.4, 2004LCD,12864LCD, TFT28 and TFT32. 10. Available to input 24V, the heated bed current can be reduced to 1/4 at the same system power which effectively resolves the problem that the MOSFET of heated bed heats. 11. X axis, Y axis and Z axis with different color terminal controls the stepper motors and endstops, which is convenient to wire. 12. Plug the stepper drivers according to the different color terminals which decreases the probability of reverse and prevents the controller board damage. TMC2208 TMC2208 single-axis stepper motor drive chip, power tube built-in drive current 1.4A peak current 2A, voltage range 4.75V-36V, 256 subdivision; Flexible microPlyer interpolation unit, the component can provide up to 256 microstep / step resolution, even in the pulse rate is limited system can still be perfect to achieve sinusoidal control; Both components have pulse / direction input, can be completely independent operation. The configuration is implemented via digital input. More Info. about TMC2208 (Please click here) Package Included: 1x MKS-Gen L V1.0 board 1x 50cm USB cable 5x TMC2208 V1.0 Stepper Motor Driver 5x Heatsink 1x Screwdriver

Features: The processor uses high performance MCU ATmega328, and uses external 8MHz crystal oscillator as the system clock. Using 1.8 Inch LCD display, resolution of 128X160, support 65536 colors. Single button operation, support automatic shutdown for reducing power consumption. Support battery power supply, shutdown current less than 20nA. Each measurement time is about 2S, and only when measuring capacitance or inductance, the measurement time becomes longer. Automatic detection of NPN, PNP bipolar transistor, N channel, P channel MOSFET and JFET, diode, double diode, P-IGPT, thyristor, double thyristor and so on. For some thyristors and double thyristors, the transistor tester can not be tested when the current and current can not be satisfied. For some IGPT with a driving voltage of more than 5V, the transistor tester can not test it. Support the identification of the pins of test elements. Supports the measurement of current amplification factor and base emitter turn-on voltage of bipolar transistors. The Darlington transistor can be distinguished by the turn-on voltage and the current amplification factor. The gate threshold voltage, gate capacitance and drain to drain source resistance of the RDSon under the 5V gate voltage are tested to test the MOSFET. Supports simultaneous measurement of two resistors, and data is displayed in four bit decimal format. Support potentiometer test, but when the potentiometer is adjusted to one end, at this time can not distinguish between the intermediate pin and the end pin. The minimum resistance resolution is 0.01 ohms, and the maximum resistance is 50M ohm. A capacitor can be measured with a capacitance range of 25pf~100mF and a resolution of 1pF. The capacitance less than 25pF can be measured by parallel with another known capacitance greater than or equal to 25pF, and the measured capacitance value can be obtained by subtracting the known capacitance value. When the capacitance greater than 90nF is tested, the series equivalent resistance is also displayed, with a resolution of 0.01 ohms. When the capacitance greater than 5000pF is tested, the voltage loss after the test pulse can be measured, and the quality factor of the capacitor can be estimated by this parameter. Supports simultaneous measurement of two diodes with additional display diode voltage drop. LEDs are identified as diodes, and the test voltage drop is much larger than that of conventional diodes. The two-color diode is identified as two diodes. The equivalent inductance of the resistor less than 2100 ohms is also measured at the same time, with a range of 0.01mH~20H, but the measurement accuracy is not very good. Program with self-test function, support a variety of parameters calibration. Support frequency generator function, output by TP2, output frequency range from 1Hz to 2MHz. Support a fixed frequency signal output from the TP2, you can adjust the duty cycle by the button. Special attention: The capacitor must be discharged before testing the capacitor, otherwise it may damage the test pin. When testing the components on the circuit board, it is necessary to disconnect the power supply on the circuit board, and the residual voltage is not allowed on the test equipment. Hardware circuit: Each interface is illustrated as follows: J1: 2.54-2PIN white seat is used to input DC 7~12V voltage; S1: red button, reset button; S2: green button, operation button, used for one button operation of the entire circuit board; Instructions: 1. Components placed The transistor tester is very simple, and the test pins TP1, TP2 and TP3 are all in sequence. For only two pins, the components only need to be placed to any two test pins. For three pins of the components, randomly placed three test pins. Two resistors and two diodes can be tested at the same time. 2. Press the S1 reset button to shut down, and then press the S2 boot key to start a new measurement. 3. After the start of the long press S2 (more than 1S), enter the additional function selection interface, after a short press for moving the cursor on the attachment, long into the function interface button corresponding to the cursor interface, the various functions are as follows: Package included: 1 x ATmega328 digital transistor tester kits with shell

Description: The SAMD21 M0 represents a powerful, 32-bit extension of the Arduino UNO platform. The board is powered by SAMD21 MCU, featuring a 32-bit ARM Cortex M0 core. Compatible with Arduino Zero and Arduino M0. The SAMD21 M0 board expands the family by providing increased performance, enabling a variety of project opportunities for devices, and acts as a great educational tool for learning about 32-bit application development. The Zero applications span from smart IoT devices, wearable technology, high tech automation, to crazy robotics. The board is powered by SAMD21 MCU, which features a 32-bit ARM Cortex M0+ core. One of its most important features is Atmel’s Embedded Debugger (EDBG), which provides a full debug interface without the need for additional hardware, significantly increasing the ease-of-use for software debugging. EDBG also supports a virtual COM port that can be used for device and bootloader programming. Package included: 1 x Wemos® SAMD21 M0 32-bit ARM Cortex M0 Core

SELECTED OPTION: DESIGN: BLUEDIGITALTUBERED&GREENLEDWITHHOUSING CLICK HERE for more options in this item. Here is the case link for this clock  ID: 1053594 Product ID 1013812: Date, time, temperature by turns display and. Alarm clock function, the whole point timekeeping and music alarm function. Pioneered light control, There are eight options for the Chime ringtone and Alarm clock Alarm. A variety of colors LED optional. There are 8 kinds of LED: Blue digital tube+ Red & Blue LED with housing Blue digital tube+ Red & Green LED with housing Blue digital tube+ Red & Blue LED without housing Blue digital tube+ Red & Green LED without housing Red digital tube+ Red & Blue LED with housing Red digital tube+ Red & Green LED with housing Red digital tube+ Red & Blue LED without housing Red digital tube+ Red & Green LED without housing Green digital tube+ Red & Blue LED with housing        Green digital tube+ Red & Green LED with housing      Green digital tube+ Red & Blue LED without housing     Green digital tube+ Red & Green LED without housing Description:   Size: With       housing: 93 x 93 x 26 mm Without housing:   81 x 81 x 2 mm PCB thickness: 1.6 mm Materials: FR4 military level Operating voltage: DC5V Note: The color of the new case is blue as follwing picture, which is not affect the function.   Function:    Alarm clock: You can set the alarm for the length of time, and the music The whole point timekeeping: You can set the whole point of timekeeping, and the music   There are 7 kinds of music you can set:   A. "D""D""D""D" (Default alarm tone)  B. Broadcast timekeeping (The whole point timekeeping default ringtone) C. Jasmine (Chinese music) D. For Elise  E. Canon F. Give a little Time to Your Love (Richard Clayderman) G. BBK  (Chinese music)   Welding note:   1, P1 for the development of the interface, not welding. 2, component identification: Components with no positive or negative polarity: Resistance (R1~R15), Thermistor(RT1), Ceramic capacitors (C4, C5), Monolithic capacitor (C2, C3), Crystal oscillator (Y1), Keys (S1, S2). Distinguishing positive and negative elements:LED(D1~D60),Battery seat(BT1),Electrolytic capacitor(C1), Buzzer(LS1),These elements should be noted that the positive and negative poles of the circuit board are to be noted. Other multi pin element:IAP15W413AS (U1), DS1302(U2), S8550(Q1), Block USB (USB1), These  elements should be noted in the same direction as the circuit board. 3,Positive welding LED, digital tube, Thermistor, and other components of the welding in the back. 4,LED has two colors, the less number of color welding in a large number of corresponding position, and the rest of the  location of a number of more than one color. 5,U2, C4, C5, Y1, BT1 must be welded before the digital tube, pay attention to the points on the digital tube. 6,The working voltage of the kit is 5V, the battery on back is only for the power down save time. Schematic circuit:   Package included:   1 x Upgrade DIY EC1515A DS1302B Rotation LED Electronic Clock Kit 51 SCM Learning Board  

    Features: Integrated image collecting and algorithm chip together, ALL-in-One Fingerprint reader can conduct secondary development, can be embedded into a variety of end products Users can conduct secondary development, can be embedded into a variety of end products, such as: access control, attendance, safety deposit box, car door locks Low power consumption, low cost, small size, excellent performance Professional optical technology, precise module manufacturing technics Good image processing capabilities, can successfully capture image up to resolution 500 dpi Finger  detection function.   Specification: Type: Optical  Sensor Life: 100 million times Static indicators: 15KV Backlight: Blue Interface: USB2.0/UART(TTL logical level) RS232 communication baud rate: 9600BPS~115200BPS changeable Image Capture Surface 15×11(mm) Verification Speed:  0.2 sec Scanning Speed: 0.3 sec Character file size:  256 bytes Template size:  512 bytes Storage capacity: 1000 Security level: 3 (1,2,3,4,5(highest)) False Acceptance Rate (FAR):≤0.0001% False Rejection Rate (FRR): ≤0.1% Resolution 500 DPI Voltage:4.2--6VDC (or 3.3V) Working current: Typical ≤75mA Matching Method:  1: N Operating Envirement Temperature: -20 to 50 degrees R307 fingerprint module size chart   R307 fingerprint module circuit board diagram     3.3VDC power may be selected to supply when short ciucuit as the following drawing. Caution: Operating carefully, and R307 will be damaged when wong connection.

Instruction: Click to open We will default sending carton package, please note about this before you buy it. Introduce: 1. This kit is easy to use, powerful, able to meet the needs of the vast majority of DIY enthusiasts. 2. If you feel this basic kit can not meet your demand for electronic DIY fanatic, then the Deluxe kit is definitely your best choice, both kit contains all the learning, but also contains a part of electronic building blocks module! 3. We carefully selected a variety of DIY components, sensors, etc., as many as 40 kinds of species, so having all the fun you can want to achieve their own DIY electronic products. Features: Arduino Uno R3 module expansion boards, bread boards, flexible connection to your module 4x4 keyboard and driver board Digital control module Bluetooth module can achieve data transmission with mobile phone 125KHz RFID, can achieve credit card, access control, etc Wireless Remote Control Servos, stepper motors, DC brush motor, play a variety of motor control Package included:

New from TASCAM, the MD-CD1 combines CD playback and MiniDisc recording in a single rackmount unit designed to save rack space and installation budgets. Like all of TASCAM's products designed for fixed installation, the MD-CD1 is a reliable player designed for years of trouble-free use. The unit is stocked with features, such as 12% pitch control, MP3 CD playback, RS-232 control and an optional balanced I/O board that allow it to be spec'd into a wide variety of applications. The TASCAM MD-CD1 has a host of professional features like RS-232 control, digital I/O and an optional I/O board for balanced interfacing. CDs can be played back at up to 12% higher or lower, and can even be played back faster without changing the pitch for a "chipmunk" effect. Discs can be duplicated from CD to MiniDisc at up to 4x speed, and a wireless IR remote is included.

An amazing Buy for just R, has all the features of the top of the range Go Pro, with High-definition digital motion video recording device tailored to market demand. It has a variety of industry-leading features including digital video recording, photo shooting, audio recording, video display and detachable battery, which makes it perfect for vehicle data recording, photo-shooting, outdoor sports, home security, deep-water probing, etc., allowing you to film at anytime, anywhere. Water-resistant casing that allows you to film fascinating water sports; water-resistant up to 30 meters under water High definition screen that displays and replays fascinating videos recorded. Detachable battery that is easy to replace and prolongs your camera’s service life. Video recording while charging. Video recording with battery. 12-megapixel HD wide-angle lens. HDMI HD output. Web camera. Multiple video recording formats: P 720P WVGA Recorded in MOV format Multiple photo shooting modes: Single shot, Snapper SD card Excluded (can take SD cards up to 32 gigs) I currently use a 2 gig in mine and storage wise works great ! · This Camera comes complete with ALL attachment’s as seen in the Pics: Charger – also includes USB charging J Helmet Mounts Handle Bar mounts – for Bicycle & Motorbike Surf Board / Flat Mounts Industrial Double sided tape – works great I have mine attached to my Body Board Car windscreen mount Camera Sj & Protective Casing

This Camera is an amazing Buy for just R, has all the features of the top of the range Go Pro, with Wifi built in along with High-definition digital motion video recording device tailored to market demand. It has a variety of industry-leading features including digital video recording, photo shooting, audio recording, video display and detachable battery, which makes it perfect for vehicle data recording, photo-shooting, outdoor sports, home security, deep-water probing, etc., allowing you to film at anytime, anywhere. Water-resistant casing that allows you to film fascinating water sports; water-resistant up to 30 meters under water High definition screen that displays and replays fascinating videos recorded. Detachable battery that is easy to replace and prolongs your camera’s service life. Video recording while charging. Video recording with battery. 12-megapixel HD wide-angle lens. HDMI HD output. Web camera. Multiple video recording formats: P 720P WVGA Recorded in MOV format Multiple photo shooting modes: Single shot, Snapper SD card Excluded (can take SD cards up to 32 gigs) I currently use a 2 gig in mine and storage wise works great ! · This Camera comes complete with ALL attachment’s as seen in the Pics: Charger – also includes USB charging J Helmet Mounts Handle Bar mounts – for Bicycle & Motorbike Surf Board / Flat Mounts Industrial Double sided tape – works great I have mine attached to my Body Board Car windscreen mount Camera Sj & Protective Casing

DC-DC Adjustable Step Up Power Module Description: Show some use more advanced microprocessor voltmeter, boost part by the United States imported boost controller, by utilizing the power MOSFET's on-resistance and eliminates the need for a current sense resistor, maximizing efficiency, efficiency up 96.4%. Imports of high-power low-impedance MOS, big package, high current, high efficiency Schottky, wide thick PCB traces, power efficiency and low temperature rise is guaranteed. Wide voltage, output voltage when the input can be achieved in more than 20V 128W output power. Long-life high-frequency switching power supply for high-capacity low resistance (low ESR) electrolytic capacitor, so that the lower output ripple. Parameters:   Input voltage: 3 ~ 35V DC (Note: The input voltage is less than 4V, onboard voltmeter failure) Input Current: 9A (max) Output voltage: 3.5 ~ 35V DC (This board is a step-up board, the output voltage to be> = input voltage) Output Current: 6A (max) Output Power: 75W, (when the input voltage is greater than 20V output can reach 128W) Conversion efficiency: 96.7% (maximum) Output ripple: 24mV (TYP) Onboard voltage meter range: 4 ~ 40V, error + -0.1V Short circuit protection: (limit current 14A). Tips: When access to high-power load, due to the impact of current are just machines Assembly limiting self-locking protection, it is recommended to boot, then access to the load. Input Reverse Polarity Protection: None (if necessary, please enter the string into the high current diode) A key switch digital tube light off, a key switch input and output voltage measurements. (On-board voltage indicator "IN" highlight the input voltage, "OUT" highlight the output voltage). Applications:   DIY a power supply, 5V input can be output can be 5-35V adjustable. Power supply for your electronic device, according to your system can set the output voltage value. For example 3.7V Lithium Mobile Power l do 5V, 7.4V or 12V 19 liters to the laptop power supply. As car power supply for your laptop, PDA or a variety of digital products supply. Package included: 1 x DC-DC Adjustable Step Up Power Module  

Introduction: New version of Biaxial Spherical Rotating. Part of rotary plate are using high-power wireless power supply, rotating noise greatly reduced. System power supply voltage 12V2A (please use your own power), rotating motherboard using STM8S105K4T6 single-chip control, plug-in 8 Mbit flash storage text, pictures, animation! Through the host computer software to send text, pictures, animation, calibration time, PC software support Chinese and English input. Clock chip using DS1302 with backup battery, support the remote control to adjust the time. Remote control switch a variety of display modes, to provide some open source C program, suitable for learning purposes. Note: This is a DIY kit, you need to have some electronic knowledge and ability. SMD is unsoldered!! The kit has certain difficulty, please buy according to your own situation. Don't comes with TTL serial downloader. Dual axis of each 56 LEDs display. Motor speed is high, no shell, please be careful to use! Red light / blue light can be soldered according to personal preferences in the inner and outer ring. Hardware parameters (error 2mm): Acrylic board: 16.2 * 16.2cm Main control board: 12.5 * 4.8cm Side panel: 9cm high / 7.5cm high Finished product reference height: 11cm Package includes: 1 x DIY Spherical Rotating LED Kit

Description: This Nano Mult-Function expansion board is designed specially for Arduino Nano, solve the problem of wiring confusing when a variety of sensors connected. Lead out all digital IO port and analog IO port, each one with standard positive and negative power interface. Lead out the I2C interface of mainboard for convenient connection. Increasing the DC power supply interface. Nano USB interface supply current is actually only 50MA, to bring high-current devices, such as the steering, is obviously insufficient. So in the DC power connector provide external power supply to ensure the stability of equipment operation. Package included: 3 x Nano shield

Description VS1053 MP3 Shield The VS1053 is a great MP3 decoder, it is capable of decoding Ogg Vorbis/MP3/AAC/WMA/MIDI audio and encoding IMA ADPCM and user-loadable Ogg Vorbis, can drive 30 ohm headphones with no additional power supply. This VS1053 MP3 Shield is designed based on VS1053B from VLSI. For the best headphone listening experience, the VS1053 includes EarSpeaker spatial processing which accurately simulates how a room with stereo loudspeakers would sound. In addition to being able to decode all major formats, VS1053 is capable of recording in Ogg Vobis files. With the SD card slot on the other side of the board, you can play mp3 files from SD card using this shield. It is easily to drop it in your project or make a mp3 player using your Arduino Quick Spec Can play a variety of music formats, support for OGG encoding real-time recording SPI interface, the control signal lines are led out A headphone and stereo output A microphone for recording A line_in input interface Power indicator 3.3V and 2.8V of LDO chip AMS-1117 on board, provides up to 800mA current A single power supply: +5 VDC 12.288 Mhz crystal SD card slot Audio Sample Listen to an audio sample recorded with a VS1053 using the Wideband Voice profile Resources Mp3 Shield Detailed Introduction VS1053 Datasheet Wiki Shipping List 1 X VS1053 MP3 Shield More Products View More Products

If you're looking for old-school analog handling in a package armed to the teeth with modern reliability, the search is over. This mixer's British EQ, 24 mic inputs (each with its own built-in studiograde XENYX preamp), 8 stereo inputs and 8 buses give you enough leeway to craft the recording of your dreams or create the perfect mix for a live show. What the Heck is "British EQ"? British EQ is a smashing thing to have on your side when you start reaching for those channel equalization knobs at a live concert or in the studio. The EQ's on British consoles from the 60s and 70s are what many engineers believe does their sound the best justice. When it comes to tweaking your sound, they're kind, gentle and above all, musical. It's like drinking a fine scotch instead of fortified wineor maybe receiving a warm hug instead of a kick to the crotch. British EQ's distinct configuration of wider curves/lower Q and harmonic phase characteristics allows you to add or subtract EQ more generously than you can with conventional EQ circuit designs. When you add low midrange, you get a firmer sound instead of a nasty bonk. When you back high frequencies off a bit, treble backs off just a hair instead of turning muffled. The Ins and Outs Some manufacturers make what they call 32-input mixers that count features like CD/TAPE IN as an input. But the SX really gives you 24 mono channels and four stereo channels (with two 1/4" inputs apiecean additional 8 inputs), making it easy to accommodate a wide variety of studio or live performance configurations. That means you can connect up to 24 microphones or other mono instruments and up to four stereo instruments (keyboards, for example). You also get eight buses, allowing you to assign multiple channelssay all the mics on a drum kit or all the backup singers' micsto a single fader. Best of all, you don't need a black belt in engineering to operate the SX. The mono channels are grouped along two-thirds of the board, featuring dials in uniform primary colors (Gain in white; EQ in blue; AUX in red; Pan in black). Sub groups are located next door to the Main and Mono faders in the bottom right corner. Directly above, there's a handy built-in talkback mic that sends signal to your AUX 1-2 monitors via a push button, as well as a multi-purpose 13-LED master level meter to give you a dynamic visual gauge of the selected output. The SX's intuitive patch bay makes it equally at home in the club or studio. You get two balanced XLR MAIN outputs as well as a two 1/4" TRS MAIN outs. There's also a 1/4" MONO OUT (perfect for a subwoofer output). Eight SUBGROUP OUT jacks allow you to send your buses to an external recording device. This section also includes AUX SEND jacks for connection to monitors, CD/ TAPE input and output jacks, and FX send/return jacks for use with outboard effects processors. Directly below, you'll fi nd the 1/4" headphone/ control room out jack. A Million Ways To Change The Channel At the top of each mono channel, you'll find both a balanced XLR input with a XENYX mic preamp and a 1/4" input. A phantom power switch located on the back near the main power switch accommodates condenser mics. Each mono channel has a 3-band EQ with semi-parametric mids (giving you control of the Mid level and a sweepable frequency with a boost or cut of 15dB) and a Trim control for adjusting input gain via a Level Set LED. A Low Cut button eliminates the frequencies where unwanted infrasonics such as mic handling noise occur. The eight AUX dials control the volume of the AUX SEND 1/4" output signals (more on that below). Stereo channels feature the same functions, but a with dual 1/4" inputs and a different EQ. Instead of sweepable mids, stereo channels feature High Mid and Low Mid dials, both with bell center frequencies set at 8 kHz and 800 Hz, respectively. This is especially useful for EQ'ing the critical midrange frequency content found in keyboard signals. Near every mono channel's fader you'll find a and MAIN button. By engaging the MAIN button, the signal is sent to the main mix. Or, if you engage the 1-2 button, the channel becomes part of a bus. Twist the PAN control all the way to the left to assign it to Sub 1, or all the way to the right for Sub 2. The same principle applies to the and 7-8 buttons. A Mute button with accompanying LED cuts the signal from the channel, and a Clip LED helps you dial in a distortion-free post-EQ signal. The Solo button on individual channels routes the subgroup signal to the solo bus or Pre-Fader Listendepending on whether the signal has been included in a subgroup. Finally, each of the eight buses feature an independent fader, Solo switch, and Left and Right buttons to assign them to Left or Right stereo channels. Buy it now. Teach your great grandkids how to run it. BEHRINGER mixers last and last. We use top quality parts such as longwear faders, sealed rotary controls and premium circuit boards. We have 20 years of experience figuring out how to compensate for clumsy loadins, spilled drinks, crazed guitarists and millions of road miles. The result is a mixer you can count on day after day and night after night. Hitch Your Art to the AUX The SX has eight AUX SEND outputs as well as eight AUX return inputs, giving you more routing options than a Los Angeles road map. AUX SEND 1-8 allow you to send the signal governed by an individual channel to an outboard FX unit or EQ. Meanwhile, the AUX returns can be thought of as eight extra line inputs working as four stereo pairs. You can apply up to 20 dB of gain to these inputs. AUX returns 1, 2, 7 and 8 allow returning FX to be sent to tape, and, along with 5 and 6, are also good for cuing artists via headphones. AUX returns 3 and 4 are always assigned to the main bus. Take On The World Not every town on the planet uses the same voltage common in yours. Unfortunately, this sometimes doesn't occur to jet-setting sound technicians until they're miles from home. With the SX, this is never an issue. The internal auto-range power supply can run on anything from 100 to 240 V with noise-free audio, top-quality transient response and low power consumption. Why Do You Need This Mixer? Built-in pristine XENYX mic preamps British-style EQ dials give you the sound and control preferred by top studio engineers Awesomely complete I/O everything from bus inserts to mono output Product Features: Behringer SX Mixer

AYRA 5 is a two-way reference studio monitor that is designed for near field applications, equally suited to your home recording studio. AYRA 5 features a high quality soft dome tweeter and a 5” composite fibreglass woofer. The AYRA Series is optimized to deliver the best sound for a variety of applications. Whether you are working with a near field mix at your home studio, you need a clear and loud sound for your multimedia gaming or simply need some good monitors for your personal computer. Applications • Home Recording • Studio Recording • Personal Monitoring • DJ Monitoring • Multimedia • AV production facilities Features True active 35 W + 20 W class AB design 50 Hz – Hz frequency response Precision directivity tweeter waveguide Fully featured input board 5″ composite fiberglass woofer 1″ soft dome tweeter Reflection free front cabinet design Low distortion reflex port Acoustical Specifications Frequency Response -3 dB: 55 Hz ÷ 20 kHz Max SPL: 106 dB Horizontal coverage angle: 110° Vertical coverage angle: 70° Compression Driver: 1″, 25mm coice coil Woofer: 5″ Input/Output Section Input signal: 10 K ohm Input connectors: XLR, Jack, RCA Input sensitivity: -2 dBu Processor Section Crossover frequencies: Hz Limiter: Soft limiter Controls: HF adjust Amplifier Specifications Total power: 55 W High frequencies: 20 W Low frequencies: 35 W Connections: VDE Free delivery on orders over a R in Gauteng. Delivery 1-3 days depending on area Warranty Type: Dealer 12 Months Warranty. All goods are subject to supplier discretion Replacement Guarantee: 30 Days: All goods are subject to supplier discretion