V5 expansion board geekcreit

Buy UNO R3 Sensor Shield V5 Expansion Board Geekcreit for Arduino - products that work with official Ard for R198.00

Buy Sensor Shield V5.0 Sensor Expansion Board Geekcreit for Arduino - products that work with official A for R201.00

3Pcs UNO R3 Sensor Shield V5 Expansion Board For Arduino Feature: This Arduino Sensor Shield V5.0 sensor expansion board, the motherboard is not only extended out the Arduino Uno all digits and analog interface to servo line order form, but also add hoc IIC interface, servo controller interface, Bluetooth module communication interface, SD card module communication interface, APC220 radio frequency module communication interface, ultrasonic sensor interface, 12864 LCD serial and parallel interfaces, independent expansion will be more easy and convenient. Package included: 3 x UNO R3 Sensor Shield v5

Buy NANO IO Shield Expansion Board Geekcreit for Arduino - products that work with official Arduino boar for R174.00

Buy Geekcreit ProtoBoard Shield Expansion Board For D1 Mini Double Sided Perf Boar... (QUANTITY: 5PCS) for R250.00

Buy Geekcreit ProtoBoard Shield Expansion Board For D1 Mini Double Sided Perf Boar... (QUANTITY: 3PCS) for R207.00

Buy Arduino UNO R3 V5.0 Sensor Shield Expansion Board **LOCAL STOCK** for R65.00

Buy 20pcs ESP8266 WIFI Development Board Base Expansion Board V3 Backplane Geekcreit for Arduino - pr... for R859.00

Buy 5Pcs Geekcreit 328P Multifunction Expansion Board V3.0 For NANO UNO for R278.00

Buy 3pcs ESP8266 WIFI Development Board Base Expansion Board V3 Backplane Geekcreit for Arduino - produc for R197.00

Buy 2.8 3.2 Inch TFT/SD Shield Expansion Board For DUE LCD Module SD Card Adapter Geekcreit for Arduino for R312.00

Description: The IIC 2004 LCD display module is a 4 line 20 character LCD module not only set the contrast control knob selector switch also has a backlight and IIC communication interface. For Arduino beginners, not for the cumbersome and complex LCD driver circuit connection and a headache, the real significance of this LCD module will simplify the circuit, this module directly into the Arduino Sensor Shield V5.0 sensor expansion board IIC device interface can, GM 4P sensor connection cable, programmed through the Arduino controller, you can easily identify the slogan, sensor data records. Specification: Supply voltage: 5V Interface: I2C I2C address: 0x27 or 0x3F Pin definition: GND, VCC, SDA, SCL Contrast adjust: potentiometer The module is a low-power consumption character LCD module with a built-in controller The module can be easily interfaced with a MCU Display format: 20 Characters x 4 lines Fully assembled and tested serial LCD 20 x 4 module White text, blue backlight It is fantastic for Arduino based project Size: 9.8 x 6 x 1.2mm Package included: 1 x 2004 LCD display module

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 1 x Uno R3 Board 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Needles

Buy Multi-Function Funduino Nano Shield Nano Sensor Expansion Board Geekcreit f for R169.00

Instruction: Click to open We will default sending carton package, please note about this before you buy it. Introduce: 1. This kit is easy to use, powerful, able to meet the needs of the vast majority of DIY enthusiasts. 2. If you feel this basic kit can not meet your demand for electronic DIY fanatic, then the Deluxe kit is definitely your best choice, both kit contains all the learning, but also contains a part of electronic building blocks module! 3. We carefully selected a variety of DIY components, sensors, etc., as many as 40 kinds of species, so having all the fun you can want to achieve their own DIY electronic products. Features: Arduino Uno R3 module expansion boards, bread boards, flexible connection to your module 4x4 keyboard and driver board Digital control module Bluetooth module can achieve data transmission with mobile phone 125KHz RFID, can achieve credit card, access control, etc Wireless Remote Control Servos, stepper motors, DC brush motor, play a variety of motor control Package included: