Uno motor

Buy UNO R3 Starter Kits 1602 LCD L293D Motor LED Matrix MB102 Breadboard for R500.00

Description: - This Arduino uno development kit, is designed based on the Arduino uno board, together with 2-channel & 16-channel servo shield board to drive the tank and 2WD car. In addition, There has wireless contoller and receiver, you can control the tank car via wireless control. - Provide source code, APP, and manual. Specifications: About Active Buzzer: - Size: 3.2cm * 1.3cm - Module Interface Description: 1. VCC external 3.3V-5V voltage (which can be connected directly with the 5v microcontroller and 3.3v microcontroller) 2. GND External GND 3. I/O external microcontroller IO port About Arduino Uno Development Kit: Description: - The Arduino Uno Development Kit, with the ability to control 2 motors and 16 servos at the same time, is ideal for developing mobile robots such as robotic arms, trolleys, tank chassis and more. - This set of development board is based on ESP8266 development and is compatible with Arduino UNO R3. - It can control 2 motors and 16 servos at the same time. It is suitable for mobile robot driving control with a robotic arm. ESPduino is an Arduino board with WiFi function. Features: - Can control 2-way motor and 16-way servo at the same time; - Using Bluetooth (reserved in-line interface) or WiFi control; - Using plug-in design. Power connection method: - Disconnect VM and VIN, (separate control motor, 6 ~ 36V); - Open circuit VS and VIN, (control servo separately, 6 ~ 18V); - Short circuit VM and VIN while shorting VS and 5V. At the same time control the motor (6 ~ 18V) and 16 5V servos. Package Included: 1 x 2-channel motor&16-channel servo shield board 1 x UNO board 1 x USB Cable 1 x Wireless controller 1 x Receiver 1 x Active buzzer 1 set Copper pillar kit 1 x 18650 Battery box 1 x Dupont line

Arduino Starter Kit     Please check shipping information before placing an order   General   Compatible with Arduino High quality Board: UNO R3   Package Contents   Arduino UNO R3 Board 400 point Breadboard USB Cable 9V Wall Power Adapter (1A) Remote control for Ardunio 1602 LCD Ardunio Protosheild w/ Mini Breadboard 65 X MM Jumper Wires (assorted length) 4 Pin DuPont Wires SG90 9G Servo Stepper Motor Stepper Motor Driver 100 x Resistors (10 each / 10, 100, 200, 330, 1K, 2K, 5K, 10K, 100K, 1m ohm) 9V Battery 1 Channel Relay Module 8*8 Dot Matrix Module 7 Segment Display (4 digit) 7 Segment Display (1 digit) MPU 6050 Accelerometer and Gyroscope Module XY Joystick Module HCSR04 Ultrasonic Sensor Module Small Plastic Box (with components) 5 x BC547 NPN Transistor 5 x BC557 PNP Transistor 2 x Photoresistor (LDR) 5 x 1N4007 Diodes 5mm LED (5 each / blue, green, yellow, white, red) RGB LED (Common Cathode) 2 x 10K Potentiometer 74HC595 8 Bit Shift Register MAX7219 Chip (LED Driver) Thermistor Piezo Buzzer 5 x 22pF Capacitors 5 x 0.1uF Capacitors 2 x 50V 10uF Capacitors 2 x 50V 100uF Capacitors 5 x Push Button Switches H-Bridge Motor Driver IR Receiver 3V DC Motor 5 x PN2222 Transistors Breadboard Holder 40 PIN Header            

Features: The most complete performance starter kit with all the essential arduino products. 174 PCS essential Arduino components. Includes lastest Arduino components to turn your idea into a real product. Arduino display includes IIC/I2C interface was developed to reduce the IO port usage on Arduino board Description: Simply the best Arduino kit with most complete components These lessons are old and outdated. Tons of updated lessons and Arduino codes are availabe on Google and Youtube for free! Just make sure that Arduino kit you ordering includes all the parts you need. Parts included in this package: 1 x Compatable Arduino Uno R3 Board 1 x Protoshield 1 x USB Cable for Arduino R3 board 1 x Mini Breadboad for R3 Protoshield Board 1 x 4X Pin Header for Uno R3 Board 1 x I2C Address: 0x27 1 x Infrared Phototransistor 1 x Ball Switch 1 x Infrared Sensor 1 x Infrared Receiver 1 x S8050 Transistor 1 x 5516 LDR Photo Resistor 5 x Color Switch 10 x Green 3mm LED 10 x Red 3mm LED 10 x Yellow 3mm LED 1 x 1k Rotary Switch 1 x 10k Rotary Switch 1 x 100k Rotary Switch 1 x Stepper Motor 1 x Stepper Motor Controller 1 x Sound Sensor 1 x 1 Channel Realy 1 x 9Volt Battery Holder 1 x Distance Sensor 1 x Digital Temp Sensor 10 x Male to Male Dupont Cable 10 x Male to Female Dupont Cable 10 x Female to Female Dupont Cable 1 x 4 Bits Digital Tube LED 1 x 1 Bits Digital Tube LED 1 x 8x8 Dot Matrix Digital Tube 1 x Joystick controller for Arduino 1 x 74HC595IC 1 x Active Buzzer 1 x Passive Buzzer 30 x 300 ohm Resistor 30 x 1K ohm Resistor 30 x 10 ohm Resistor 1 x Straight 40 Pin Header 1 x L Shape 40 Pin Header

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 1 x Uno R3 Board 1 x CNC Shield Board 4 x A4988 Stepper Motor Driver 4 x Heat Sink 1 x USB Cable 1 x 40-Pin Row Needles

Feature: The Compatible Arduino Starter Kit is designed for the new comers to Arduino. We think people will get a deep impression for their electronic knowledge if they can perform DIY things. So this kit includes a lot of discrete components and some interesting and easy to use modules. Through this Kit you can do many interesting projects. From basic simple Arduino project like LED blink to more complex usage like I2C RTC or Infrared remote controlling, just make your thought fly. We provide some learning lessons for starters, but you can also make your own interesting projects by using the parts of the Kit. Package included: 1 x Compatible UNO R3 board 1 x Breadboard (830 points) 1 x USB cable 1 x 9V battery 1 x Remote control 1 x IIC 1602 LCD 1 x Protoshield with mini breadboard 1 x 65mm jumper wire (assorted length) 1 x 8*8 Dot matrix module 1 x SG90 9G wervo set 1 x Stepper motor 1 x Stepper motor driver 30 x Resistor 1 x 9V Battery connection 1 x 7-Segment display (4 digit) 1 x 7-Segment display (1 digit) 1 x Small plastic box (with component) 1 x Photoresistor (LDR) 25 x 5mm LED (5 each / green, yellow, red) 1 x 10K Potentiometer 1 x 74HC595 8 bit shift register 1 x Thermistor 2 x Piezo buzzer cactive&Passtive) 4 x Push button switche 1 x H-Bridge motor driver 1 x IR receiver 4 x Cap 1 x Pin header

Buy Starter Kit for Arduino Uno R3 - Uno R3 Breadboard and Holder Step Motor / Serv for R960.08

Description Overview Arduino product family is a great learning platform for electronics, programming and robotics. But most projects at some point require mobility. This board allows for motor control with Arduino right away. Stack up this shield on your controller and drive motors with higher power requirements. Depending on the motor of choice, you can make it fast or handle a higher payload. This Arduino Compatible Motor Shield (2A) uses L298P chip which allow to drive two 7-12V DC motors with maximum 2A current. This shield can be directly mounted onto standard Arduino Duemilanove and Arduino Mega. Speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the motor control is signalled by Arduino Digital Pin 4 and 7. The Motor shield can be powered directly from Arduino or from external power source. It is strongly encouraged to use external power supply to power the motor shield. Specifications Logic Control Voltage: 5V (From Arduino) Motor Driven Voltage: 6.5~12v(VIN Power Supply),4.8~35V (External Power Source) 2 way motor drive Logic supply current Is: 36mA Motor Driven current Io: 2A Maximum power consumption:25W Up to 2A current each way Pin 4,5,6,7 are used to drive two DC motor Support PWM speed control Support PLL advance speed control Size: 55x55mm Compatibility: Arduino UNO Arduino UNO R3 Arduino Mega 1280/2560 More Products View More Products

- CNC Shield Board Version: 3.0 Color: Red Size(L*W*H): 68 x 53 x 18 mm Voltage: DC 12~36 V (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.) Features: 1. Uses removable A4988 or DRV8825 compatible stepper drivers. 2. The extension board can be used for carving machine, 3 d printer driver expansion board 3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals) 4. PWM Spindle and direction pins,4-Axis support (X, Y, Z, A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13) 5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place. 6. Please note that this is an unassembled kit and Basic soldering skills are needed. - A4988 Stepper Motor Driver Color: Red Size(L*W*H): 20 x 15 x 10 mm Thermal shutdown circuitry: Yes Crossover-current protection: Yes Ground fault protection: Yes Load short-circuit protection: Yes Compatible logic supply: 3.3V and 5 V Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16 Features: 1. Mix with slow current decay modes. 2. Internal UVLO and Low RDS (On) Output. 3. Automatic current decay mode detection/selection. 4. Synchronous rectification for low power dissipation. 5. Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. - Uno R3 Board MCU: ATmega328 Clock speed: 16 MHz USB interface: ATmega16U2 Operating voltage: 5 V I-I / O pin output current: 40 mA max 3.3 V output current: 150 mA max Digital I/O pins: 14 (including 6 with PWM capability) Analog input pins: 6 EEPROM: 1 kB Static RAM (SRAM): 2 kB Flash memory: 32 kB Size(L*W*H): 68 x 53 x 10 mm Click to download universal course Package included: 3 x CNC Shield + UNO R3 Board + 4x A4988 Driver Kit

Description Type: Drive IC is_customized: Yes Brand Name: keyestudio Condition: New Application: Electric Toy Package: Other Introduction Keyestudio super learning kit is suitable for Aduino enthusiasts. This kit includes 32 projects with detailed tutorials, starting from the basics to more complex projects. Different from other kits, it adds some functional modules, such as RFID, temperature and humidity module. There is connection diagram and code for each project, making it easy for you to learn. Kit list Keyestudio UNO R3 board for Aduino *1 LED - Blue *5 LED - Red *5 LED - Yellow *5 LED - RGB *1 220 Ω resistor *8 10K Ω resistor *5 1K Ω resistor *5 10K Ω Pot *1 Buzzer (active) *1 Buzzer (passive) *1 Large button switch *4 Ball tilt sensor *2 Photo Resistor *3 Flame sensor *1 1x LM35 Temp Sensor *1 IC 74HC595N 16-pin DIP *1 7-seg LED 1x module *1 7-seg LED 4x module *1 8*8 LED Matrix *1 2x16 LCD display *1 IR receiver *1 IR remote control *1 Servo Motor *1 Stepper driver module *1 Stepper Motor *1 Joystick module *1 Relay module *1 PIR Motion Sensor *1 Analog MQ-2 Gas Sensor *1 ADXL345 Three Axis Acceleration Module *1 HC-SR04 Ultrasonic Sensor *1 DS3231 Clock Module *1 DHT11 Temperature and Humidity Sensor *1 Soil humidity sensor *1 rc522 RFID module *1 RFID card *1 RFID key *1 Pin headers *40 830-hole Breadboard *1 Dupont connector wires *10 Jumper Wire *30 6-cell AA Battery pack *1 USB cable *1 Project list: 1: Hello World 2: LED blinking 3: PWM 4: Traffic light 5: LED chasing effect 6: Button-controlled LED 7: Active buzzer 8: Passive buzzer 9: RGB LED 10: Photo resistor 11: Flame sensor 12: LM35 temperature sensor 13: Tilt switch 14: IR remote control 15: Analog value reading 16: 74HC595 17: 1-digit LED segment display 18: 4-digit LED segment display 19: 8*8 LED matrix 20: 1602 LCD 21: 9g servo control 22: Stepper Motor 23: PIR Motion Sensor 24: Analog MQ-2 Gas Sensor 25: ADXL345 Three Axis Acceleration Module 26: HC-SR04 Ultrasonic Sensor 27: Joystick Module 28: 5V Relay Module 29: DS3231 Clock Module 30: DHT11 Temperature and Humidity Sensor 31: Soil Humidity Sensor 32: RC522 RFID module Video PDF

Arduino WiFi Control Kit with Arduino UNO R3 Board + Motor Drive Shield Board + WiFi Module

Buy CNC Kit With UNO + Shield + Stepper Motor DRV8825 Endstop A4988 GRBL - Free Shipping for R1,925.00

Buy KW-AR-Mini Kit with 17 Classes UNO R3 DC Motor Breadboard LED Components Set Geekcreit for R480.80

Features: 1. Programmable and you can add functions. 2. TP4056 charger module to charge your Li-ion battery. 3. 18650 Li-ion battery solution power both L298N and UNO board. 4. Android bluetooth control, obstacle avoidance, IR remote control and line tracking/follower 4 functions in 1 smart robotic car. About the UNO: Add A6 and A7 analog I/O. Come with SHIELDED USB cable for stable data transit. Add two rows of the pass-thru holes for connecting normal dupont line. This UNO is manufactured using the Creative Commons files, compatible with Arduino software(IDE) in every way. Specifications: Material: Circuit Board + Electronic Component Finished Car Size: (L)X(W)X(H)21.6X12X13.5cm/8.50''X8.07''X5.31''(appr.) Package included: 1 x 4WD Acrylic Chassis Kit (4 Motors + 4 Wheels + 2 Acrylic body + 4 Encoder Disc + 1 Boat shape switch + 1 bag of screws and bolt) 1 x UNO R3 Board (Fully ARDUINO-Compatible) 1 x Shielded USB Cable 1 x V5 Sensor Shield 1 x L298N Dual H Bridge Motor Driver Module 1 x HC-06 Bluetooth Module 1 x IR Receive Module 1 x IR Remote Controller (Battery CR2032 included) 3 x Line Tracking Sensor Module 1 x HC-SR04 Ultrasonic Range Finder 1 x Acrylic Bracket for HC-SR04 Ultrasonic Range Finder 1 x SG90 Servo 1 x Acrylic Bracket for SG90 Servo 40 x Female to Female Dupont Cable 7 x Red Electronic Cable 5 x Black Electronic Cable 2 x TP4056 battery charging module (For charging one 18650 battery cell one time only) 3 x 18650 Battery Holder (2 in 1 type 1piece and single type 2pcs.18650 Battery NOT INCLUDED)

Feature: The Compatible Arduino Starter Kit is designed for the new comers to Arduino. We think people will get a deep impression for their electronic knowledge if they can perform DIY things. So this kit includes a lot of discrete components and some interesting and easy to use modules. Through this Kit you can do many interesting projects. From basic simple Arduino project like LED blink to more complex usage like I2C RTC or Infrared remote controlling, just make your thought fly. Package included: 1 x Uno R3 Board 1 x Breadboard 1 x Prototype Shield 1 x 4x4 keypad 1 x 5V relay module 1 x step motor driver 1 x gas sensor 1 x IIC module 1 x sound module 1 x JoyStick 1 x Clock module 1 x servo 1 x stepper motor 1 x LCD1602 1 x IR controller 10 x Push button switch 1 x 7-Segment display(1-digit) 1 x 7-Segment display(4-digit) 1 x Dot Matrix 2 x 10K Potentiometer 1 x Active Buzzer 1 x Passive Buzzer 11 x Color Switch 1 x MAX7219 1 x 74HC595 1 x 4N35 1 x 10uF capacitor 1 x flame sensor 1 x Photo resistor 1 x IR receiver 1 x IR sender 1 x RGB LED 1 x Tilt 1 x LM360Z 1 x Monolithic capacitor 1 x L Shape 40 Pin Header 1 x Straight 40 Pin Header 10 x Green 5mm LED 10 x Red 5mm LED 10 x Yellow 5mm LED 10 x 220R Resistor 10 x 1K Resistor 10 x 10K Resistor 20 x Female-Female cable 20 x Female-male cable 65 x jumper wires 1 x USB cable 1 x 9V battery cable

Instruction: Click to open We will default sending carton package, please note about this before you buy it. Introduce: 1. This kit is easy to use, powerful, able to meet the needs of the vast majority of DIY enthusiasts. 2. If you feel this basic kit can not meet your demand for electronic DIY fanatic, then the Deluxe kit is definitely your best choice, both kit contains all the learning, but also contains a part of electronic building blocks module! 3. We carefully selected a variety of DIY components, sensors, etc., as many as 40 kinds of species, so having all the fun you can want to achieve their own DIY electronic products. Features: Arduino Uno R3 module expansion boards, bread boards, flexible connection to your module 4x4 keyboard and driver board Digital control module Bluetooth module can achieve data transmission with mobile phone 125KHz RFID, can achieve credit card, access control, etc Wireless Remote Control Servos, stepper motors, DC brush motor, play a variety of motor control Package included:

There are six kinds for your choice: A: Gold Chassis B: Gold Chassis + Espduino kit C: Gold Chassis + NodeMcu Lua kit D: Silver Chassis E: Silver Chassis + Espduino kit F: Silver Chassis + NodeMcu Lua kit Introduction: A novel design has already coming for the tank chassis, with beautiful shape and full metal aluminum alloy structure. In this tank chassis, a space for 9g servo is left for the ultrasonic sensor, and a space for MG995 servo is also left to rotate the mechanical manipulator. What is more, UNO R3 and NodeMCU development boards are also designed to install. In addition, the metal panel can be used to install the wheeled car by install the 25mm or 37mm motor frames. Interesting, a LED light is installed to brighten the dark in the night. Under the help of the motor, the tank chassis can be smoothly turn left, right, circle, forward and backward etc. Therefore, when you get the chassis, it can do many things for you, like getting the temperature and mobile monitor. Certainly, we have developed a series of car/tank chassis. Features: 1. Reserve the space for 9g, MM95, MM96R gear; 2. Reserve for the installation holes for UNO R3 and NodeMCU development board kit; 3. Reserve the space for robotic manipulator; 4. Design the LED light for the dark moving and brighten the light; 5. Add the 25mm and 37mm motor frame, can change the 4WD smart car 6. with Hall sensor and feedback 7. The metal chassis is generated by aluminum alloy; 8. The bearing wheels and the driving wheels are metal 9. The bearing wheel piece is connected by the stainless steel and two bearings, which can let the bearing wheel is rotate freely with small frictions 10. The chassis can bearing the weight is about below 5kg; we test the 2.3kg 11. All the chassis are metal, excluding the track (plastic) Specification: Name: T100 Intelligent track car/tank chassis Material: aluminum alloy Wheel: metal Track: plastic Product size: about 200*190*80mm (length * width * height) Color: golden yellow silver. Motor Parameters: Name: 25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise: 56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Diameter. Of Shaft phi 4mm, D3.5 Encoder: 2pulses/circle Working voltage for sensor: 3-5V Note: The tank car chassis is not assembled. Track can be connected by any length with a needle. Package included: 1 x Chassis 2 x Driving wheels 4 x Bearing wheels 2 x Tracks (can be changed the length) 2 x DC motor 2 x LED light

Buy 4WD bluetooth Control Smart Robot Car Kit with Motherboard & N20 Gear Motor for UNO R3 Nano for R1,662.15

Geekcreit™ DIY T200 NodeMCU Aluminum Alloy Tank Track Caterpillar Chassis Smart Robot Kit Description: A novel design has already coming for the tank chassis, with beautiful shape, and full metal aluminum alloy structure. In this tank chassis, a space for 9g servo is left for the ultrasonic sensor, and a space for MG995 servo is also left to rotate the mechanical manipulator. What’smore, UNO R3 and NodeMCU development boards are also designed to install. In addition, the metal panel can be used to install the wheeled car by install the 25mm and/or 37mm motor frames. Interesting, a LED light is installed to brighten the dark in the night. Under the help of the motor, the tank chassis can be smoothly turn left, right, circle, forward and backward, ect. This tank/car chassis is assembled by ESP8266 WiFi module, Based on which, doit company has already designed and developed the mobile phone App with Android and iOS version. By the Apps, the tank/car chassis can finish some basic functions, such as, forward, left & right, back, and return. Doit company provides the richful documents, including the source code, which can let many developers, lovers, and students to DIY the wanted functions. More details, please see the "download" menu. Some useful download links:   Motor DataSheet for Tank/Car Chassis: http://bbs.smartarduino.com/showthread.php?tid=2039 Chassis Installation http://bbs.smartarduino.com/forumdisplay.php?fid=21 Software manumal http://bbs.smartarduino.com/showthread.php?tid=2036 Android App http://bbs.smartarduino.com/showthread.php?tid=1978 iOS App http://bbs.smartarduino.com/showthread.php?tid=2037 FirmWare http://bbs.smartarduino.com/showthread.php?tid=2013 Motor shield http://bbs.smartarduino.com/showthread.php?tid=6 NodeMCU http://bbs.smartarduino.com/forumdisplay.php?fid=2 Specification:   Name: T200 Intelligent track car/tank chassis Material: aluminum alloy Wheel: metal Track: plastic Product size: about 300 x 220 x 55mm (length x width x height) Weight: 1200g Color: golden yellow Motor Parameters:   Name:25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise: 56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Dia. Of Shaft phi 4mm, D3.5 Encoder: 2pulses/circle Working voltage for sensor: 5V Shipping List: Chassis:1 pcs Driving wheels: 2 pcs Bearing wheels: 6 pcs Track:2 pcs (can be changed the length) DC motor: 2 pcs LED light: 2 pcs NodeMCU development kit: 1 set 18650 battery box: 1pcs(Batteries not included ) Screws:several Screw tools: 3 pcs

DIY C300 Aluminum Alloy Metal Wheel Car Chassis For Arduino NodeMCU There are six kinds for your choice: A: Gold Chassis B: Gold Chassis + Espduino kit C: Gold Chassis + NodeMcu Lua kit D: Silver Chassis E: Silver Chassis + Espduino kit F: Silver Chassis + NodeMcu Lua kit Introduction: A novel design has already coming for the tank chassis, with beautiful shape, and full metal aluminum alloy structure. In this tank chassis, a space for 9g servo is left for the ultrasonic sensor, and a space for MG995 servo is also left to rotate the mechanical manipulator. What’s more, UNO R3 and NodeMCU development boards are also designed to install. In addition, the metal panel can be used to install the wheeled car by install the 25mm and/or 37mm motor frames. Interesting, a LED light is installed to brighten the dark in the night. Under the help of the motor, the tank chassis can be smoothly turn left, right, circle, forward and backward, ect. Therefore, when you get the chassis, it can do many things for you, like getting the temperature and mobile monitor. Certainly, we have developed a series of car/tank chassis. Hoping you can choose your loved car chassis. Specifications: Name: C300 Intelligent car chassis Material: aluminum alloy Wheel: Rubber (has blue and red colors.) Product size: about 200*120*70mm Motor Parameters: Name: 25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise:56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Diameter Of Shaft phi 4mm, D3.5 Encoder: 2pulses/circle Note: This is DIY kit and unassemble kit. Package included: 1 x Chassis 4 x Wheels 4 x Copper couplings 4 x DC motor 2 x LED light

Introductions: - Imported Ozon wood as raw material, cut by laser - The structure fully utilizes Luban's wisdom to achieve less screws and simplifies the assembly process for the user. - After the installation is completed and the battery is attached to this "weight block", the tumbler balance principle is fully utilized, and the center of gravity is changed by a powerful and powerful motor to realize the movement of the hot wheels. - In the process of self-assembling and reviving the hot-wheel robot, the child has a deeper understanding and study of the principles of mechanics and electronics. - This robot is able to be remote controlled with the help of "Goble" - A Generic BLE APP Controller. (iOS Only) **The wiki about this product for your reference. Please clcik. Specifications: - Dimensions: 120 x 120 x 85mm -  Operating Voltage: 6 - 10V -  Operating Current: 0 - 3A -  Operating Temperature: 0 - 60°C -  Master controller: Romeo BLE mini control board -  Range: Open area within 30m -  Arduino Bluetooth remote update program -  Microprocessor: ATmega328P -  Boot loader: Arduino UNO -  2-way 1.5A current H-bridge motor driver interface -  Drive: two differential drive -  Motor no-load speed: 230 ± 10% rpm -  Max Speed: 1 m/s Note: 1. This product is suitable for children and adolescents aged 8 years and over. Children under 6 years old should be accompanied by parents. 2. The battery connection must be confirmed again and again. Do not reverse it. Otherwise it will burn out the control board. 3, the current APP only supports iOS client, Android client is under development! Package Included: Romeo BLE mini main control board (DFR0351)x1 Hot Wheel A Board x1 Hot Wheel B Board x1 Geared motor x2 Battery box x1 Screw package x1 Manual x1

Features: -Noveland elegant appearance: 1) Reserve the space for 9g, MM95, MM96R gear; 2) Reserve for the intallation holes for UNO R3 and NodeMCU development board kit; 3) Reserve the space for robotic manipulator; 4) Design the LED light for the dark moving and brighten the light; 5) Add the 25mm and 37mm motor frame, can change the 4WD smart car. -Aluminum alloy: 1) The metal chassis is generated by aluminum alloy; 2) The bearing wheels and the driving wheels are metal; 3) The bearing wheelpiece is connected by the stainless steel and two bearings, which can let the bearing wheel is rotate freely with small frictions. -Solid structure: 1) The chassis can bearing the weight is about below 5kg; we test the 2.3kg; 2) All the chassis are metal, excluding the track (plastic). -Powerful force: 1) It is very powerful; 2) with Hall sensor and feedback; Specifications: Name: T100 Intelligent track car Material: aluminum alloy Wheel: metal Track: plastic Product size: about 200 x 190 x 80mm (length  x  width x height) Weight: 740g Voltage: 9V-12V Motor Parameter: Name: 25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise :56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Dia. Of Shaft phi 4mm, D3.5 Encoder: 2pulses Working voltage for sensor: 3-5V Note: The board is not included. Package included: 1 x Chassis 2 x Wheels 4 x Bearing wheel 2 x Track (can be changed the length) 2 x DC Motors 2 x LED light

DIY T600 Metal Wall-E Tank Chassis Robot Crawler Track DIY T600 Metal Wall-E Tank Chassis Robot Crawler TrackThere are three kinds you can choose:A: Silver Chassis WheelB: Silver Chassis Wheel Espduino kitC: Silver Chassis Wheel NodeMcu Lua kitD: Golden Chassis WheelE: Golden Chassis Wheel Espduino kitF: Golden Chassis Wheel NodeMcu Lua kitA novel design has already coming for the tank chassis, with beautiful shape, and full metal aluminum alloy structure. In this tank chassis, a space for 9g servo is left for the ultrasonic sensor, and a space for MG995 servo is also left to rotate the mechanical manipulator. Whatﾒs more, UNO R3 and NodeMCU development boards are also designed to install. In addition, the metal panel can be used to install the wheeled car by install the 25mm and/or 37mm motor frames. Interesting, a LED light is installed to brighten the dark in the night. Under the help of the motor, the tank chassis can be smoothly turn left, right, circle, forward and backward, ect. Therefore, when you get the chassis, it can do many things for you, like getting the temperature and mobile monitor. Certainly, we have developed a series of car/tank chassis. Hoping you can choose your loved car chassis. Specifications: Name: T600 Intelligent track car/tank chassisMaterial: aluminum alloyWheel: metalTrack: plastic Motor Parameters: Name: 25mm gear motorOutput speed: 150ﾱ10%rpmNo_load current: 200mA (Max)Stall current: 4500mA(max)Stall torque: 9.5kgNaNRated speed: 100ﾱ10%rpmRated torque: 3000gNaNRated current: 1200mA (Max)Noise: 56dBWorking voltage: 9VOutside Shaft Length: 14.5mmShaft End Play: 0.05-0.50mmScrew Size: M3.0Diameter Of Shaft phi 4mm, D3.5Encoder: 2pulses/circleWorking voltage for sensor: 3-5V Note: For the shipping convenience, the tank car chassis is not assembled.Track can be connected by any length with a needle. Package included: 1 x Chassis4 x Driving wheels20 x Bearing wheels2 x Track (can be changed the length)2 x DC motor2 x LED light

Introduction: This tank/car chassis is assembled by ESP8266 WiFi module, Based on which, doit company has already designed and developed the mobile phone App with Android and iOS version. By the Apps, the tank/car chassis can finish some basic functions, such as, forward, left & right, back, and return. Doit company provides the richful documents, including the source code, which can let many developers, lovers, and students to DIY the wanted functions. More details, please see the "download" menu. Feature: 1) Reserve the space for 9g, MM95, MM96R gear; 2) Reserve for the intallation holes for UNO R3 and NodeMCU development board kit; 3) Reserve the space for robotic manipulator; 4) Design the LED light for the dark moving and brighten the light; 5) Add the 25mm and 37mm motor frame, can change the 4WD smart car; Aluminum alloy: 1) The metal chassis is generated by aluminum alloy; 2) The bearing wheels and the driving wheels are metal; 3) The bearing wheelpiece is connected by the stainless steel and two bearings, which can let the bearing wheel is rotate freely with small frictions. Solid structure: 1) The chassis can bearing the weight is about below 5kg; we test the 2.3kg; 2) All the chassis are metal, excluding the track (plastic). Name: T300 Intelligent track car Material: aluminum alloy Wheel: metal Track: plastic Product size: about 290 x 270 x 100mm (length x width x height) Color: golden yellow / silver. Optional Motor Parameter: Name: 25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise:56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Dia. Of Shaft phi 4mm, D3.5 Encoder: 2pulses Working voltage for sensor: 3-5V Package included: 1 x Chassis 2 x Wheels 10 x Bearing wheel 2 x Track 2 x DC Motors Several Screw 1 set NodeMCU development board kit

Description: There are some electronic modules,you will more interested during learning procedure. Provide learning lessons and technique support. You will know more about Arduino when you are assembling these modules. Android bluetooth control,obstacle avoidance,IR remote control and line tracking/follower 4 functions in 1 smart robotic car. 18650 Li-ion battery solution power both L298N and UNO board. TP4056 charger module to charge your Li-ion battery. Package included: 1 x 4WD Acrylic Chassis Kit (4 Motors + 4 Wheels + 2 Acrylic body + 4 Encoder Disc + 1 Boat shape switch + 1 bag of screws and bolt) 1 x UNO R3 Board (Fully ARDUINO-Compatible) 1 x 50cm Long Shielded USB Cable 1 x V5 Sensor Shield 1 x L298N Dual H Bridge Motor Driver Module 1 x HC-06 Bluetooth Module 1 x IR Receive Module 1 x IR Remote Controller 3 x Line Tracking Sensor Module 1 x HC-SR04 Ultrasonic Range Finder 1 x Acrylic Bracket for HC-SR04 Ultrasonic Range Finder 1 x SG90 Servo 1 x Acrylic Bracket for SG90 Servo 40 x Female to Female Dupont Cable 7 x Red Electronic Cable. 5 x Black Electronic Cable. 2 x TP4056 Battery Charging Module (For charging one 18650 battery cell one time only) 3 x 18650 Battery Holder Here is the link of the (←click here) for your reference, you may download for yourself

The accessories about the TP200 Intelligent Tank Chassis car for your reference.   Product ID: 1253162 and  Product ID: 1265462 Features: 1. All-metal structure, making the tank more solid and firm  2.  Reserved 9g servo and MG995 servo installation space, can be used to flexibly install ultrasonic sensors and robots, etc 3. Designed mounting holes for Arduino UNO R3 and NodeMCU development boards; 4. The mounting holes are reserved for the installation of the robot arms and the like; 5. The design can be installed 2 LED headlamps position, can be carried out at certain Chengde night 6. The panel can be based on your needs, an increase of 25mm and 37mm motor bracket can be changed into a 4-wheel drive car. 7. After the experiment can load 2.3kg, the maximum should be able to load 5kg. Specifications: - Name: TP200 Intelligent Tank Chassis - Material: Aluminum Alloy - Surface treatment: sandblasting oxidation - Color: Silver - Track: Engineering Plastics - Size: about 300 * 220 * 55mm (length * width * height) Note: * Product does not include the control board kit. Package Included: 1 x  TP200 Intelligent Tank Chassis Car Kit  

  This kit walks you through the basics of Arduino and electronics in a hands-on way. You will be able to build 15 projects using components that let you control the physical world through different kinds of sensors and actuators. Once you have mastered this knowledge, you will have a palette of code and circuits to create something beautiful, and make someone smile with what you invent. So build, hack and share! Projects you can make: - 01 GET TO KNOW YOUR TOOLS: an introduction to the concepts you'll need to use this kit - 02 SPACESHIP INTERFACE: design the control panel for your starship - 03 LOVE-O-METER: measure how hot-blooded you are - 04 COLOUR MIXING LAMP: produce any colour with a lamp that uses light as an input - 05 MOOD CUE: clue people in to how you're doing - 06 LIGHT THEREMIN: create a musical instrument you play by waving your hands - 07 KEYBOARD INSTRUMENT: play music and make some noise with this keyboard - 08 DIGITAL HOURGLASS: a light-up hourglass that can stop you from working too much - 09 MOTORIZED PINWHEEL: a coloured wheel that will make your head spin - 10 ZOETROPE: create a mechanical animation you can play forward or backward - 11 CRYSTAL BALL: a mystical tour to answer all your tough questions - 12 KNOCK LOCK: tap out the secret code to open the door - 13 TOUCHY-FEEL LAMP: a lamp that responds to your touch - 14 TWEAK THE ARDUINO LOGO: control your personal computer from your Arduino - 15 HACKING BUTTONS: create a master control for all your devices! The kit includes: 1 x Arduino Projects Book (170 pages); 1 x Arduino UNO rev.3; 1 x USB cable; 1 x breadboard; 1 x wood base; 1 x 9 V battery snap; 70 x hard cable; 2 x flexible cable; 6 x photoresistor; 3 x trimmer d10 kohm; 10 x push button; 1 x temperature sensor; 1 x tilt sensor; 1 x LCD (16x2i); 1 x LED (white); 1 x LED (RGB); 8 x LED (red); 8 x LED (green); 8 x LED (yellow); 3 x LED (blue); 1 x CC motor 6/9 V; 1 x servomotor; 1 x piezo; 1 x H bridge; 2 x photocoupler; 5 x BC547; 2 x IRF520; 5 x 100 nF capacitor; 3 x100 µF capacitor; 5 x 100 pF capacitor; 5 x 1N4007 diode; 3 x transparent jelly (red, green, blue); 1 x male strip connector (40x1); 20 x 220 ohm resistor; 5 x 560 ohm resistor; 5 x 1 kohm resistor; 5 x 4.7 kohm resistor; 10 x 10 kohm resistor; 5 x 1 Mohm resistor; 5 x 10 Mohm resistor.

The accessories about the TP200 Intelligent Tank Chassis car for your reference. Please skip Product ID: 1253162 and Product ID: 1265462 Features: 1. All-metal structure, making the tank more solid and firm 2. Reserved 9g servo and MG995 servo installation space, can be used to flexibly install ultrasonic sensors and robots, etc 3. Designed mounting holes for Arduino UNO R3 and NodeMCU development boards; 4. The mounting holes are reserved for the installation of the robot arms and the like; 5. The design can be installed 2 LED headlamps position, can be carried out at certain Chengde night 6. The panel can be based on your needs, an increase of 25mm and 37mm motor bracket can be changed into a 4-wheel drive car. 7. After the experiment can load 2.3kg, the maximum should be able to load 5kg. Specifications: - Name: TP200 Intelligent Tank Chassis - Material: Aluminum Alloy - Surface treatment: sandblasting oxidation - Color: Silver - Track: Engineering Plastics - Size: about 300 * 220 * 55mm (length * width * height) Note: * Product does not include the control board kit. * Due to different producing batches, product details might be a little different. Thank you for understanding. Package Included: 1 x TP200 Intelligent Tank Chassis Car Kit