Tube arrow

Buy RED ARROW Five Star Shank Lathe Wood Turning Tool Carbide Insert Cutter Tools with Carbon Fiber Tube for R1,865.19

25/50/75LBS Magnetic Welding Locator Welding Magnetic Clamp Angle Arrow Holder Package weight: 0.31 kg Description: 25/50/75LB Switch magnetic soldering clamp, this welding magnet is designed to work as an extra hand, enables fast and accurate holding of any ferrous object. Specification: Material: Ferrite Color: Red Type: 25LBS/50LBS/75LBS 25LBS: Dimension 120x80x15mm Max soldering 30-40cm Suction capacity 11kg 50LBS: Dimension 155x102x16mm Max soldering 50cm Suction capacity 22kg 75LBS: Dimension 190x120x26mm Max soldering 70-80cm Suction capacity 35kg Features: 1. Ideal for being used as holder and positioner in welding, soldering,marking off, pipe installation. 2. Compact Angle Arrow design, will hold both sheet and tube at angles of 45, 90 and 135 degrees. 3. Can be used as double sided holder for welding and assembly work. Package Included: 1pc x Magnetic Welding Clamp Notice: 1. Please allow a bit error due to manual measurement. please make sure you do not mind before you bid. 2. The color may have different as the difference display, pls understand. More Details: Click here for more deals 25/50/75LBS Magnetic Welding Locator Welding Magnetic Clamp Angle Arrow Holder 25/50/75LBS Magnetic Welding Locator Welding Magnetic Clamp Angle Arrow Holder

Description: 2pcs 450mm Plastic Extension Wands Wet Dry Vacuum Cleaner Accessory Tool Specification: Material:Plastic Size: Length: 45cm/17.7" Large Side Inner Diameter: 3.5cm/1.4" Small Side Outer Diameter: 3.4cm/1.3" Features: Fit for: Haier/ Midea/ ELX (Electrolux)/ Sanyo / Panasonic brands European version vacuum cleaner with inner-Dia. 35mm connector and other Japanese version vacuum cleaners with outer-Dia. 33-34mm connector. Instructions: Small side insert into the large side. Easy to install and easy to clean. Connect multiple wands, could reach and clean ceiling. Reach and dust out the arrow space easily, make the housework so easy. Package Included: 2 x Vacuum Extension Wand Tube   More Details:

Introductions: - This filament run out sensor unit is designed to detect whether your printing is run out of filament. - During printing, if the unit detected that there is out of filament it will send a signal to the main board. - With correct firmware settings, the printing will be paused until the operator reload the filament and resume the printing. Features: - It works with all available materials;flexible,clear,opaque,filled,etc. - The unit can handle as many filaments simultaneously. As soon as one of them will be missing, the unit will send a message to the next one, up to - your main board. - Two screws are provided so you can install it where you want. - Works with almost any printer. - Durable injection modeling casing and industrial grade components. Specifications: Supply Voltage: 3.3-5V Operating Temperature: below 80￢ﾄﾃ Filament Diameter: 1.75MM(1-2MM) Filament Presence: low Filament Absent: high(equal to Supply Voltage) Primary cable: 80cm extension cable: 20cm PTFR tuble: 50cm Cable color: Red — 3.3-5V Yellow/Blue — Signal Black — GND 1. Install: Please install the unit after the spool and before your extruder. Fix it on your printer and along with the path of the filament is recommend. Pay attention to the direction indicated by the arrow on the body. Inserted the 4mm PTFE tube to both sides of the unit for guiding the filament and help to reduce the friction. 2. Connections: Servo pins always have the right pins:5V, Ground, and Signal. Most endstop pins will have the same 3 pins, and sometimes only Signal and Ground. If you only have these two, there should be a 5V somewhere else on your main board. In theory, you can choices any input pins on your mainboard for the signal. 3. Firmware configuration: Marlin: Make sure your firmware has the filament runout feature, you need Marlin 1.1.0-RC7 or newer. If you are using an older version, contact your 3D printer manufacturer or update your firmware configuration manually. 4. Expansion: If you want to install more than one unit on the same printer just connect the unit one to each other then connect to the main board at the end. They just parallel connection on the circuit Level. So the signal output can’t tell which one is run out actually but you can check the flashing LED on the unit to find out. Package Included: 1 x Filament runout sensor