Tork craft repl container
Top sales list tork craft repl container
South Africa (All cities)
Buy Tork Craft repl. Jaw set pipe wrench heavy duty 450mm for R143.00
R 143
See product
South Africa (All cities)
Buy Tork Craft Repl. Cord & Clamp Set (57-60) Service Kit for R108.00
R 108
See product
South Africa (All cities)
Buy Tork Craft Repl. Carbon Brush (42) Motor Service Kit for R109.00
R 109
See product
South Africa
Pilot drill bit for hole saws Drill bit diameter: Ø6.35mm Drill bit: HSS (High-speed steel) Application: The drill bit is a replacement pilot drill bit for Bi-metal hole saws. Replacing the pilot drill bit: Use an Allen key (TC17016) or in some cases a slot-head screwdriver to undo the grub screw securing the pilot drill bit in the mandrel. Replace the pilot drill bit by aligning the flat side on the shank with the grub screw. Tighten the grub screw. Make sure the pilot drill bit is secured. In some cases it would be necessary to remove the hole saw from the mandrel to replace the pilot drill bit. Mandrel replacement pilot drill bits: Ø6.35 x 115mm (extra long) for bi-metal hole saws - TC00001 Ø6.35 x 70mm for bi-metal hole saws - TC00002 Tungsten Carbide Tipped (TCT) series hole saws - TC00003 Carbide grit hole saws - TC00004 Diamond coated hole saws - TC00006
R 55
See product
South Africa (All cities)
Buy Tork Craft Thread Repair Kit M10 X 1.5 X 2.0D Repl. Inserts For Nr5010 for R101.00
R 101
See product
South Africa (All cities)
Buy Tork Craft Sanding Drum Repl. Sleeves 60 Grit Set Qty.5 13 - 50Mm for R52.00
R 52
See product
South Africa
Diamond Grit Hole Saw Diameter: Ø32mm Mandrel to use: TC17007-3 Working length: 38mm Application: The hole saw is made from a tough steel body covered in a chrome finish. The cutting edge is covered with a permanently bonded electro plated diamond grit coating. The diamond grit hole saw can be used to cut: Bricks Roof tiles Slate Ceramics Tiles Marble/Granite Reinforced plastics Glass resins Asbestos IMPORTANT: Do not use the diamond grit hole saw with percussion (hammer action). Allow the diamond coating to cut the material with minimum pressure. Rotation speed should not exceed 300 rpm. TIP: Regularly (every 1 to 2 minutes of use) rinse and cool the diamond grit holesaw in a container of water. This will extend the life of the hole saw. The maximum permissible temperature of a diamond tip is 500°C.
R 305
See product
South Africa
Diamond Grit Hole Saw Diameter: Ø15mm Mandrel to use: TC17002-3 Working length: 38mm Application: The hole saw is made from a tough steel body covered in a chrome finish. The cutting edge is covered with a permanently bonded electro plated diamond grit coating. The diamond grit hole saw can be used to cut: Bricks Roof tiles Slate Ceramics Tiles Marble/Granite Reinforced plastics Glass resins Asbestos IMPORTANT: Do not use the diamond grit hole saw with percussion (hammer action). Allow the diamond coating to cut the material with minimum pressure. Rotation speed should not exceed 300 rpm. TIP: Regularly (every 1 to 2 minutes of use) rinse and cool the diamond grit holesaw in a container of water. This will extend the life of the hole saw. The maximum permissible temperature of a diamond tip is 500°C.
R 150
See product
South Africa
Diamond Grit Hole Saw Diameter: Ø40mm Mandrel to use: TC17007-3 Working length: 38mm Application: The hole saw is made from a tough steel body covered in a chrome finish. The cutting edge is covered with a permanently bonded electro plated diamond grit coating. The diamond grit hole saw can be used to cut: Bricks Roof tiles Slate Ceramics Tiles Marble/Granite Reinforced plastics Glass resins Asbestos IMPORTANT: Do not use the diamond grit hole saw with percussion (hammer action). Allow the diamond coating to cut the material with minimum pressure. Rotation speed should not exceed 300 rpm. TIP: Regularly (every 1 to 2 minutes of use) rinse and cool the diamond grit holesaw in a container of water. This will extend the life of the hole saw. The maximum permissible temperature of a diamond tip is 500°C.
R 397
See product
South Africa (All cities)
Diamond Grit Hole Saw Diameter: Ø30mm Mandrel to use: TC17002-3 Working length: 38mm Application: The hole saw is made from a tough steel body covered in a chrome finish. The cutting edge is covered with a permanently bonded electro plated diamond grit coating. The diamond grit hole saw can be used to cut: Bricks Roof tiles Slate Ceramics Tiles Marble/Granite Reinforced plastics Glass resins Asbestos IMPORTANT: Do not use the diamond grit hole saw with percussion (hammer action). Allow the diamond coating to cut the material with minimum pressure. Rotation speed should not exceed 300 rpm. TIP: Regularly (every 1 to 2 minutes of use) rinse and cool the diamond grit holesaw in a container of water. This will extend the life of the hole saw. The maximum permissible temperature of a diamond tip is 500°C.
R 332
See product
South Africa (All cities)
Buy OSCILATING MULTI FUNCTION TOOL REPL. PUSCH ROD TORK CRAFT for R8.34
R 8
See product
South Africa
Drum sanding kit sleeves Drum sanding sleeves to use with drum sanding arbor.[click here] SIZE: Ø12.7mm, Ø19mm, Ø25.4mm, Ø38.1mm, Ø50.8mm GRIT: P180 These sleeves fit onto arbors in kit with code TCDS
R 35
See product
South Africa
Drum sanding kit sleeves Drum sanding sleeves to use with drum sanding arbor.[click here] SIZE: Ø12.7mm, Ø19mm, Ø25.4mm, Ø38.1mm, Ø50.8mm GRIT: P120 These sleeves fit onto arbors in kit with code TCDS
See product
Visit our blog
Share on Facebook
Share on Twitter