Tork craft ratchet s

Buy Tork Craft Polisher S/Kit Gear Box Housing & Screws (14/15) For Pol02 for R204.00

Ratchet screwdriver Application: The reversible ratchet screwdriver includes 10 bits inside: Phillips #1 Phillips #2 Phillips #3 Pozidrive #1 Pozidrive #2 Pozidrive #3 Slot-head 5mm Slot-head 6mm Torx T15 Torx T20 The ultimate in strength and comfort with state of the art in ratchet screwdriving. The handle is ergonomical shaped for comfort. The bit holder includes a screw guide sleeve to reduce the fastener's wobble and slipping.

Ratchet screwdriver Application: The reversible ratchet screwdriver includes 10 bits inside: Phillips #1 Phillips #2 Phillips #3 Pozidrive #1 Pozidrive #2 Pozidrive #3 Slot-head 5mm Slot-head 6mm Torx T15 Torx T20 The ultimate in strength and comfort with state of the art in ratchet screwdriving. The cushion grip will not slip. The all metal mechanism can endure high torque, as high as 300kgf.cm (29.42Nm).

Buffing pad Buffing pad material: Cotton Diameter: Ø100mm Bore: Ø6.0mm Application: The buffing pad is not supplied with a chuck adaptor spindle. TC335 is an arbor with a Ø6.0mm shaft available for the buffing pad. It is ideal for buffing jewelry and other metals. The concentrically sewn sections add strength to the buffing pad and it cleans surfaces without damaging it. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buffing pad Buffing pad material: Cotton Diameter: Ø75mm Bore: Ø6.0mm Application: The buffing pad is not supplied with a chuck adaptor spindle. TC335 is an arbor with a Ø6.0mm shaft available for the buffing pad. It is ideal for buffing jewelry and other metals. The concentrically sewn sections add strength to the buffing pad and it cleans surfaces without damaging it. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buffing pad set Included in the set: (x1) Ø75mm firm buffing pad (x1) Ø75mm medium buffing pad (x1) Ø75mm soft buffing pad (x3) Ø1/4" chuck adaptor spindles Application: It is ideal for buffing jewelry and other metals. The concentrically sewn sections add strength to the buffing pad and it cleans surfaces without damaging it. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buffing pad Buffing pad density: Firm Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Polishing compound Application: This is a regular cleaning compound to be used with a polishing buff to clean hard metals: Steel Iron Stainless steel How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessable, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occuring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buffing pad Buffing pad density: Medium Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Cleaning & Polishing kit Polishing kit: Hard metals Included in the set: (x1) 12.5mm arbor chuck adaptor (x1) #1 heavy duty cleaning compound (x1) #2 regular cleaning compound (x1) #5 light polishing compound (x1) Ø100mm medium buffing pad (x2) Ø100mm firm buffing pad Application: This is a complete kit to remove scratches, clean and polish hard metals: Steel Iron Stainless steel How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill's chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessable, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill's chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occuring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft's line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buy Tork Craft Adj.Depth S/Driving Attachment Even Pilot for R203.50

Buy Tork Craft VERNIER DIGITAL FRAC. 300MM S/STEEL 0.01MM ACC. ABS FUNC. IP54 for R1,309.57

Buy Tork Craft Adj.Depth S/Driving Attachment Even Pilot for R179.00

Buy Tork Craft Bright Finishing Compound S/Steel 1.15kg White for R357.50

Polisher Wattage: 1700W No load speed: 800-2400 RPM Supplied with a Ø180mm sponge and backing pad. Application: The polisher is a power tool used in the finishing process, used with polishing buffs and compound sponges to yield a dramatic difference on a painted surface. The objective of polishing is to remove imperfections in the clear-coat that cause the paint to look dull. Surface imperfections can include swirls, scratches, water spots, etchings, industrial fallout, oxidation, etc. Features: Professionally manufactured for the automotive paint care and detailing industries. Ergonomically designed to reduce fatigue in long term use. The polisher has various hand-held positions to better hold the polisher at angles. Gear system has a two-level deduction. With two times the amount of torque than a single gear set polisher. The polisher range: ORDER NO. DESCRIPTION WARRANTY POL01 Polisher, 800W. Supplied with Ø125mm wool buff 6 Months POL02 Polisher, 1200W. Supplied with Ø180mm wool buff 6 Months POL03 Polisher, 1700W. Supplied with Ø180mm sponge pad 6 Months The Tork Craft polisher features a built-in variable speed control. It is advisable to use the polisher on it"s lowest speed to prevent friction. Lift the polisher often away from the panel (under no-load) to allow the motor to cool down. Spare parts for the POL03 polisher: ORDER NO. DESCRIPTION POL03-05 Switch POL03-11 Electrical unit POL03-12 Thumb wheel POL03-14 Brush spring POL03-15 Carbon brushes POL03-16 Carbon brush holder POL03-25 Ball bearing POL03-27 Ball bearing POL03-33 Needle bearing POL03-39 Ball bearing