Tork craft pilot set

Buy Tork Craft Pilot Centre Drill Bit For Core Bits Short for R50.60

Buy Tork Craft Pilot Centre Drill Bit For Core Bits Short for R38.50

Buy Tork Craft Pilot Drill To Fit Tc323 Series - 150Mm for R39.00

Buy Tork Craft Saw Set 3Pc Hand/Back/Job Saw Nylon Bag for R359.00

Buy Tork Craft Chisel Set Wood Turning Hss 6 Piece Wooden Case for R3,144.00

Buy Tork Craft Chisel Set Wood Turning 300Mm Hss 5 Pcs In Wood Case for R1,268.00

Pilot drill for hollow core bit Application: This is a replacement pilot drill bit for the TC322 range of hollow core bits. NOTE: The spring is used to help prevent the "plug" from getting jammed in the hollow core bit. Always use a pilot drill bit with hollow core bits.

Annular Cutter Pilot Pin 6.3 mm Pilot Pin for 55 mm Annular Cutters Pilot pin with length of 102 mm specifically for annular cutters (broach cutters) with a cutting length of 55 mm.

Cross-hole HSS Countersink 90° HSS Cross-hole Countersink Cutter Set A cross-hole countersink is a cone-shaped tool with a cutting edge provided by a hole that goes through the side of the cone. The intersection of the hole and cone form the cutting edge on the tool. The cone is not truly symmetrical as it is essential that the cone retreats away from the cutting edge as the tool rotates. If this does not occur the cutting edge will lack clearance and rub rather than bite into the material. This clearance is referred to as cutting relief. These tools are best used as deburring tools, where the burr from a previous machining operation needs to be removed for cosmetic and safety reasons, however they may be used in softer materials (such as wood or plastic) to create a countersunk hole for a screw. Common uses: A common use is to allow the head of a countersunk bolt or screw, when placed in the hole, to sit flush with or below the surface of the surrounding material. A countersink may also be used to remove the burr left from a drilling or tapping operation thereby improving the finish of the product and removing any hazardous sharp edges. Regardless of the name given to the cutter, the surface being generated may be a conical chamfer (plunging applications) or a beveled corner for the intersection of two planes (traversing applications). A countersink is a conical hole cut into a manufactured object. The same term is used for the cutter used to cut such a hole.

Tork Craft Adjustable Depth Stop Attachment (TZ AC11A) Even pilot clutch system Included in the set: - (x1) 25mm 5/16' magnetic nut driver - (x1) 25mm 1/4'  magnetic nut driver - (x1) 25mm Phillips #2 bit - (x1) Even pilot clutch bit holder Application: The even pilot clutch system is ideal for clutch screwdriving. It can also be used with self-drilling screws on corrugated steel materials. The even pilot bit holder features an adjustable depth stop and a free rotating ring to hold and guide screws accurately. The automatic clutch release enables precise countersinking of screws in drywall, particle board and plywood.

Tork Craft Screw Pilot No.8 Carded (TZ AC26-8) Screw Pilot 90° Countersink with drill bit A convenient power tool accessory. Allows you to drill a hole and simultaneously countersink the hole for screws. A common use is to allow the head of a countersunk bolt or screw, when placed in the hole, to sit flush with or below the surface of the surrounding material. This accessory will just allow you to drill and countersink in a singel step. Accurate at all times and a very neat job. A countersink is a conical hole cut into a manufactured object.

Tork Craft 2-Piece Wire Cup Brush 75mm x M14 Set (TCW006-2) Description: - 2-Piece - 75mm x M14 - Wire Cup Brush Set (Crimmed & Knotted) - For 115 Angle Grinder 

Tork Craft 3-Piece Wire Brush Set With Separate Shaft (TCW003-2) Description: - 3-Piece - Wire Brush Set - Seperate Shaft Included

Tork Craft 5 Piece Wood Turning Chisel Set (W0601) Description: - 5 Piece Wood Chisel Set

Buy Tork Craft Replacement Drill Bit 2.4mm For Screw Pilot #6 for R18.98