Tork craft knee pad

Knee pads Application: The knee pads are protective pads that are fasten onto the knees over clothing. It is ideally used when doing work on floors or roofs. It is extremely handy when installing laminate floors; tiling floors; etc.

Buy Tork Craft Foam Pad Black Finishing Pad Sponge 200mm 8 for R198.00

Buy Tork Craft Backing Pad 100mm X 5/8 Unc For Stone Polishing for R196.08

Buy Tork Craft Backing Pad Velcro 150mm X M14 With 8mm Spindle for R93.50

Buy Tork Craft Clamp Pad And Bolt Assembly For Eg1 for R203.50

Buy Tork Craft Backing Pad Velcro 150mm X M14 With 8mm Spindle for R121.00

Buy Tork Craft Backing Pad Hook And Loop 125Mm X M14 With 8Mm Spindle for R83.00

Buffing pad Buffing pad density: Firm Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Buffing pad Buffing pad density: Medium Diameter: Ø150mm Bore: Ø12.5mm Application: The buffing pad is used together with a chuck adaptor spindle supplied with the TC874 polishing kits. Alternatively the TC336 arbor would also fit the buffing pad. How to use the compounds and the buffing pads: The adaptor is used to hold the buffing pad in the drill"s chuck. Fasten the correct buffing pad in the adaptor. Make sure the flanges are on both sides of the buffing pad. It would be best to use a drill press to polish metals. If a drill press is not accessible, use adaptor TCV01810 with a portable drill with a collar diameter of Ø43mm. Tighten the adaptor in the drill"s chuck. The buffing pad should revolve towards you at full speed. Pass the compound lightly across the face of the buffing pad. To ensure that the compound is evenly spread, hold a clean piece of scrap metal against the face of the buffing pad. This will eliminate lumps of compound from occurring. If desired, heat the item to 65°C using an oven or a heater. Warming the metal keeps the compound on the buffing pad. A cool item will draw compound from the pad and leave deposits. Use a glove to handle the warm item. Hold the metal lightly against the buffing pad. Allow the compound to do the work. If more compound is required, apply it using a wiping motion. Do not overload the buffing pad. Use Tork Craft"s line of buffing pads and compounds to clean, polish and bring to a high gloss, all metals and plastics. HEAVY DUTY CLEANING REGULAR CLEANING LIGHT POLISHING HIGH GLOSS POLISHING Hard metals 1 2 5 6 Soft metals 3 5 6 Precious metals 4 5 6

Backing pad Polishing backing pad with M14 thread. For concave wool bonnets. DIA: 150mm (6") HOLES: No THREAD: M14 VELCRO: Yes with offset Application: This is a replacement backing pad for a polisher with M14 fastening thread. There is a velcro offset to minimise damage from the sharp velcro edge. The backing pad is ideal for concave polishing bonnets. Attention: Wear eye, face and body protection

Backing pad Rubber backing pad to be used with a drill DIA: 150mm (6") HOLES: No ARBOR: Ø6mm VELCRO: No Application: This is a backing pad for fibre discs or polishing bonnets. The backing pad is fitted with an arbor to be used with electric or cordless drills. The rubber is flexible and allows for flat or contoured sanding without gouging. Attention: Wear eye, face and body protection

Backing pad Polishing backing pad with M14 thread. For concave wool bonnets. DIA: 150mm (6') HOLES: No THREAD: M14 VELCRO: Yes with offset Application: This is a replacement backing pad for a polisher with M14 fastening thread. There is a velcro offset to minimise damage from the sharp velcro edge. The backing pad is ideal for concave polishing bonnets. Attention: Wear eye, face and body protection

Backing pad Polishing backing pad with M14 thread. DIA: 125mm (5') HOLES: No THREAD: M14 with Ø8mm adapter VELCRO: Yes Application: This is a replacement backing pad for a polisher with M14 fastening thread. The backing pad includes a M14 to Ø8mm adapter. Attention: Wear eye, face and body protection

Spare part for EG1 This is a spare part for the EG1 lock mortising attachment PART NUMBER: EG15 DESCRIPTION: Clamp pad and bolt assembly (welded) for EG1

Tork Craft Quick Change Base & Arbor 35mm Fingertip Felt Polishing Pad