Sma power control module

Description: The broadband RF power amplifier small, suitable for all types of radio transmission, such as: FM shortwave radio remote control, FM FM radio transmitter, amateur radio 135-175MHz, 380-470MHz walkie-talkie transmitter to use. The low-frequency input can 1mW maximum output power of 2.0W, 512MHz maximum possible output 1.6W, 930MHz maximum possible output 1.0W, 1000MHz maximum possible output 0.8W, the amplifier is equipped with fins, long-term stability. Features: Operating Frequency: 1--930MHz Input power: 1mW (0dBm) Maximum output: 2.0W (33dBm) low frequency (10 MHz) 1.6W (32dBm) IF end (512 MHz) 1.0W (30dBm) high end (930 MHz) 0.8W (29dBm) high end (1000MHz) Operating voltage: 12V (DC) Current job: 300--400mA (determined by the output power) RF connector: SMA female standard Size: 48x48x13mm Note: 1. Never load or load impedance serious loss of time under the circumstances with the use of emission. 2. Do not increase the operating voltage to use, although you can bring the power boost, but the power consumption of the product increases, the     reliability deteriorates. 3. Note the anti-static measures, between devices have a common ground, first connect the RF interface to use, plus electricity. Package included: 1 x RF Broadband Power Amplifier Module

5Pcs PFM Control DC-DC 0.9V-5V Step-up Power Supply Module Description: Mini PFM Control On-board input voltage indicator High conversion efficiency, maximum to 96% Any DC voltage input 0.9V ~ 5V, output 5V DC voltage can be stable, with two AA batteries input to the output current of 500-600MA, single AA battery power supply output current about 200MA On-board USB female, can supply power directly to the USB interface Small dimension Specification: Input voltage: 0.9 - 5V DC Output voltage: 5V DC PCB size: 34mm x 16.2mm Applications: DIY a mobile power supply, only need one battery, you can output 5V voltage for your phone, MP3, MP4, PSP charger, very easy. In order to power your electronic devices when your device needs 5V power supply, when you only have lithium battery, this module can be directly step-up to 5V, solve your problems. Package included: 5 x Mini PFM control DC-DC USB 0.9V-5V to 5V DC boost step-up

Photoresistor Relay Control Module - 12V Product Description This is the Photoresistor Relay Control Module - 12V. It can directly control AC or DC load. Product Features Open interfaces maximum load capacity: AC 0V - 250V / 10A, DC 0V - 30V / 10A with anti-reverse function module, reverse polarity power supply without damaging the module Equipped with a power indicator light (red), relay status indicator (blue) It has four mounting bolts holes for easy installation Module size: 5.0cm * 3.0cm * 1.8cm The module comes with 30cm long free detection photoresistor leads Please confirm Availability.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Feature: 1. Support sampling rate (KHz): 8/11.025/12/16/22.05/24/32/44.1/48 2. 24-bit DAC output, dynamic range support 90dB, SNR support 85dB 3. Support for 16M bytes of SPIFLASH. For example W25Q16 (2M bytes), W25Q128 (16M bytes) 4. A variety of control modes, parallel port control mode, serial port mode, AD button control mode 5. The Miniusb interface updates voice files no need installing any software. Supports XP and WIN7 systems. 6. Support for composite playback, you can achieve report time, report the temperature 7. 30 Level voice are adjustable 8. Comes with 3W amplifier, can direct connect external speaker to complete the playback 9. Support for 8-segment voice trigger playback, IO detection, so suitable for carbon film buttons and so on 10. It can support U disk, TF card and SPIFLASH as storage media at the same time 11. Power supply: 3.2 - 5.2VDC Package includes: 1 x YX5300 MP3 Player Module YX5300 MP3 Player Module Voice Serial Port Control Module With TF Card Slot YX5300 MP3 Player Module Voice Serial Port Control Module With TF Card Slot YX5300 MP3 Player Module Voice Serial Port Control Module With TF Card Slot

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Description: 1. onboard AMS1117-3.3 chip 2. onboard DC input voltage range of 4.75 V to 12 V 3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test 4. the onboard power light, indicating whether the power supply 5. 4-way output voltage interface, convenient connection during the test 6. The board size: 48.5 (mm) x12.5 (mm) Package included: 10 x AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch 10Pcs AMS1117 3.3V Power Supply Module With DC Socket And Switch

Description: 1080P Wireless Remote Control Module Board Mini Camera DV DVR Recorder with Microphone Hidden HD Camcorder   Features: Mini camera uses 2.4G wireless remote control, remote control distance of up to 20 meters, including the curve reflects the simple, responsive. Using high-capacity battery, continuous recording up to 5 hours of recording time without the human body sensor. Use CCD lenses to ensure high-resolution, low light. It is only used for forensic purposes of public security, court reporters, lawyers, etc. Prohibited for illegal videotaping, such as for illegal videotaping constitutes a crime, our Company is out of responsibility.   Specification: Video format: AVI Video encoding: M-JPEG Video resolution: 1280 x 960 Photo: 1280 x 1024 Video frame rate: 30fps Picture format: JPG Image ratio: 4:3 Playback software: Operating system or Mainstream audio and video playback software Support System: Windows 2000/XP/2003/Vista; Macos; Linux Working time: About 25 hours Charging voltage: DC-5V Battery Type: High capacity polymer lithium battery 3000mah Interface type: Mini 8Pin USB Storage: TF card Operating Instructions: 1. Starting up: slide the switch on the machine  to ON, press the A button on the remote control, red keep bright enters the standby state 2. Take photo: In standby mode, short press the B button, and red lights flashing once, it means take a picture and save it. 3. Take video: In standby mode, short press the C key, red light flashing three times then off, then starting to take video, then press the C button, the red bright, stop recording and save. 4. Body sensor camera: In standby mode, short press the D button, the red and blue light flash three times, then enter the motion detection status. When detect a moving picture object, blue lights flash again, then start recording. 5. Shutdown: In standby mode, press the A button, blue light flashes three times, shut down. (slide switch to the off, cut off all power) 6. USB connected to the computer: open the removable disk can read the file, USB connected to the computer 7. Charging: USB connected to the computer ro charging,Or you can connect the charger, the red light flashes when charging, fully charged red keep bright.. 8. Time modify setting: Please insert the TF card to the machine, connect the computer, open the "Time" document in the removable hard disk, then change the time to current time, then save the “Time” file. After saving the file and exit security hardware, restart the machine, time setting is completed. And now video file time of watermark is set at the same time with you.   Package includeds: 1 x Module Camera 1 x USB Cable 1 x Remote Control 1 x User Manual   Details pictures:

Feature: 20A large current to drive 1200W motor, dual power tube design, variable speed 0-100% Input voltage: DC10-60V Output voltage: Load Linear Output Current: 0-20A Continuous power: 1200W Speed Type: adjusting flow Speed mode: potentiometer (linear) Speed range: 0 - 100% Control frequency: 25KHZ Connection Type: Barrier Terminal Block Knob: 097 (0-100% speed) Size: 77CM X 42CM Package included: 3 x DC 10-60V 20A 1200W PWM Motor Speed Control Module

Buy 20Pcs PFM Control DC-DC 0.9V-5V Step Up Power Supply Module for R291.38

Feature: - 1MHz Fast-mode Plus compatible owned 30mA high drive capability on SDA of I2C bus interface to drive highly capacitive bus - Each LED output can be achieved from the fully closed (default) to 4096 (12) between the maximum brightness linear programmable brightness - Software programmable open-drain LED output selection (default is push-pull) of 16 push-pull outputs (5V at 25mA sink can absorb and provide 10mA Source Current), no input function - Programmable output state is in response to an order to change or stop in order to achieve all outputs simultaneously update or byte by byte (byte-by-byte) update output (default "Stop command changes") - Active-low output enable input pin when the pin is high LED outputs can be programmed 0,1 or tri-state (high impedance power-on default) - 6 hardware address pins so that the same I2C devices can be connected to the bus 62 PCA9685 - LED output frequency (all LED) is typically 40Hz to 1000Hz (When the oscillator is 25MHz, the prescaler register default value 1EH will generate refresh rate of 200Hz) - 4 software-programmable I2C bus address (a LED group call (Call) addresses and three LED sub call (Call) address) so that the device can be set in any combination to be addressed at the same time (for example, a register for " all calls (All Call) "then all PCA9634 devices on the I2C bus can be addressed at the same time, while the second register for three different addresses, then the device group on a bus device can 1/3 at the same time be addressed), software can enable and disable I2C bus address - Software reset feature (SWRST Call) makes the device via the I2C bus reset - 25MHz internal oscillator requires no external components - The maximum allowable 50MHz external clock input - An internal power-on reset - In the SDA / SCL inputs with noise filter - Output pin has edge generation rate control - No glitches on power output - Hot-Access - Low Standby Current - Operating voltage range: 2.3V to 5.5V - 5.5V tolerant inputs - It can operate at minus 40 degrees Celsius to 85 degrees Celsius environment - ESD protection exceeds 2000V HBM / JESD22-A114,200V MM / JESD22-A115 and 1000V CDM / JESD22-C101 - JEDEC standard JESD78 into the lock test beyond 100mA Package included: 3 x PCA9685 16 Channel PWM Servo Control Module 3 x Terminal 18 x Pin

Description: 1. onboard AMS1117-5.0 chip 2. onboard DC input voltage range of 6.5 V to 12 V 3. onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test 4. onboard power light, indicating whether the power supply 5. 4-way output voltage interface, convenient connection during the test 6. board size: 48.5 (mm) x12.5 (mm) Package included: 1 x AMS1117 5V Power Supply Module With DC Socket And Switch

Description: 1. onboard AMS1117-5.0 chip 2. onboard DC input voltage range of 6.5 V to 12 V 3. onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test 4. onboard power light, indicating whether the power supply 5. 4-way output voltage interface, convenient connection during the test 6. board size: 48.5 (mm) x12.5 (mm) Package included: 3 x AMS1117 5V Power Supply Module With DC Socket And Switch

Description: 1. onboard AMS1117-3.3 chip 2. onboard DC input voltage range of 4.75 V to 12 V 3. the onboard 7 * 7 self-locking switch, convenient to control power supply turned on and off during the test 4. the onboard power light, indicating whether the power supply 5. 4-way output voltage interface, convenient connection during the test 6. The board size: 48.5 (mm) x12.5 (mm) Package included: 3 x AMS1117 3.3V Power Supply Module With DC Socket And Switch

Description: 1. The on-board TDA7266 audio power amplifier chip, double track 7W + 7W, suitable for 4-8ohm 5-15W speakers 2. The main pin has led chip, convenient external device control, on-board 2 way 5.08(mm) pitch 2P terminal, represent left and right channel output 3. The on-board dial potentiometer, can adjust the output volume 4. Support DC socket, terminal blocks, row needles 3 power input mode, the default is DC socket, working voltage: 3-18V 5. The board size: 45(mm)x33(mm) Package included: 5 x TDA7266 Audio Power Amplifier Module

The PD-5 series is a series of high-quality professional sound reinforcement active speaker cabinets with high efficiency amplifier which supply very high power levels with low distortion and a wide and smooth frequency response at any listening position (short and medium distances). PD-5 series speakers are ideal for a wide range of applications, such as disco, cinema, club, cafe, restaurant, sport facilities and other entertainment. The power module includes a two-channel mixer featuring line and microphone inputs with separate level controls and a 2-band tone control. Clip indicator indicate maximum level so easy adjust the system to get a clean sound with no distortion. They are an extremely cost-effective solution for professional applications. This active 10" PA speaker has a music power of 300W, generating an acoustic pressure level of 122dB and provides an astonishing experience. Can be operated as top or full range speaker. Comes with integrated fly points for rigging. Also ideal for use as stage monitor. Active PA speaker Class-D mosfet amplifier Music power 300W Microphone and line inputs with independent level control Two-band tone control Can be operated as top or full-range speaker Fly points for rigging Extra hard coating Supplied per piece Please confirm stock availability before purchasing

The PD-5 series is a series of high-quality professional sound reinforcement active speaker cabinets with high efficiency amplifier which supply very high power levels with low distortion and a wide and smooth frequency response at any listening position (short and medium distances). PD-5 series speakers are ideal for a wide range of applications, such as disco, cinema, club, cafe, restaurant, sport facilities and other entertainment. The power module includes a two-channel mixer featuring line and microphone inputs with separate level controls and a 2-band tone control. Clip indicator indicate maximum level so easy adjust the system to get a clean sound with no distortion. They are an extremely cost-effective solution for professional applications. This active 10" PA speaker has a music power of 300W, generating an acoustic pressure level of 122dB and provides an astonishing experience. Can be operated as top or full range speaker. Comes with integrated fly points for rigging. Also ideal for use as stage monitor. Active PA speaker Class-D mosfet amplifier Music power 300W Microphone and line inputs with independent level control Two-band tone control Can be operated as top or full-range speaker Fly points for rigging Extra hard coating Supplied per piece Please confirm stock availability before purchasing We are an authorized dealer of the best sound, dj equipment, studio equipment and lighting Free delivery anywhere in the country on orders over a R1000 Delivery 24-48 hours to all major cities 48-72 hours to outlying areas Warranty Type: Authorized Dealer 12 Months Warranty. All goods are subject to supplier discretion Replacement Guarantee: 30 Days: All goods are subject to supplier discretion Our Shop Shop F2 Second Level The Conservatory at Lakefield 106 Lakefield Avenue Lakefield Square Benoni Contact us at 110 - show phone - Tian - 718 - show phone - /Whatsapp Carlo - 844 - show phone - /Whatsapp Trading Hours: Monday - Friday 9:00am - 17:00pm Saturday 9:00am - 15:00pm If you can't find what you are looking for give us a call and we will gladly assist you