Robot yellow

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Specifications: - Tire color: transparent - Tire diameter: 70mm - Tire width: 12mm - Inner diameter: 3mm (motor with D-axis and 3mm shaft diameter, such as N20 motor) - Net weight: 28.5g - Suit for DIY and Smart Robot - Quantity: 4 Package Included: 4 x rubber wheel for smart robot 4Pcs 70*12mm Yellow Wear-resistant Rubber Wheels for N20 motor 4Pcs 70*12mm Yellow Wear-resistant Rubber Wheels for N20 motor 4Pcs 70*12mm Yellow Wear-resistant Rubber Wheels for N20 motor

Note: The car will be shipped disassembled Quantity 1 Color Yellow + Black Material PCB Features Allows build it and program it easily with tons of published free codes Application Great robot car assembly kit for Arduino lovers Other Remote control range: 10 meters Packing List 4 x Geared motor   4 x Tyre   4 x Motor fixing   2 x 100 x 213 x 5mm acrylic glass plate   1 x L298N motor driver   1 x Arduino UNO328 controller board   1 x Arduino sensor board   1 x Holder kit   1 x Steering gear   1 x Ultrasonic module   3 x Line inductive module   1 x Infrared receiver module   1 x MCU remote control   1 x Mini breadboard   1 x 18650 battery holder   2 x 18650 battery   1 x 18650 battery charger (AC 100~240V / 2-flat-pin plug)   1 x Bluetooth adapter   40 x Dupont line   1 x USB cable (100cm)   13 x Copper pillar (6 x 35mm / 7 x 6mm)   1 x 3mm screws kit General Quantity 1 Color Yellow Material PCB Features Allows Specification English Manual / Spec No Dimensions & Weight Packing List 1 * piece

Buy SG90 Universal 9g Servo Motors w/ Accessories for R/C Robot / Helicopter - Blue + Yellow for R37.19

Buy 20 PCS Sweeping Robot Cleaning Small Brush for Bissell Vacuum Cleaner, Color:Yellow for R70.16

Buy SG90 Universal 9g Servo Motors w/ Accessories for R/C Robot / Helicopter - Blue Yellow for R43.59

Specifications: - Tire color: transparent - Tire diameter: 70mm - Tire width: 12mm - Inner diameter: 3mm (motor with D-axis and 3mm shaft diameter, such as N20 motor) - Net weight: 28.5g - Suit for DIY and Smart Robot Package Included: 1 x rubber wheel for smart robot

Specifications: - Tire color: transparent - Tire diameter: 70mm - Tire width: 12mm - Inner diameter: 3mm (motor with D-axis and 3mm shaft diameter, such as N20 motor) - Net weight: 28.5g - Suit for DIY and Smart Robot - Quantity: 2 Package Included: 2 x rubber wheel for smart robot

Specifications: Track width: 15mm Color: As shown Size(Length x Width): appr. 10 x 7cm Power: 2 x AA battery Voltage: 3V The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Click to watch installing and debugging video Note: Battery is not included. Package included: 1 x Tracking Robot Car Kit

The Assembly Steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Package Include: 1 X Module Smart Tracking Robot Car Electronic DIY Kit With Reduction Motor Set 1 X User Manual

Tracking Robot Car Electronic DIY Kit With Reduction Motor The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Note: We don't supply any manuals please note about this befor you buy it. Package included: 5 x Electronic DIY Kit (batteries are not included)

Tracking Robot Car Electronic DIY Kit With Reduction Motor The assembly steps: Step 1: Welding circuit Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance, is important to use multimeter to confirm resistance is correct, D4, D5 R13 R14 can temporarily not welding, integrated circuit chips can temporarily not inserted Step 2: Mechanical assembly The red line is connected to the 3V positive power supply, the yellow line grounding, excess wire can be used for motor wire. Step 3: The installation of a photoelectric circuit Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging The right direction is along the universal wheel direction, if you press and hold the left photoresistor, the wheels on the right side of the car should be rotated. Press and hold the right photoresistor, the wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring of back side. Note: We don't supply any manuals please note about this befor you buy it. Package included: 3 x Electronic DIY Kit (batteries are not included)

Specifications: 1.Photoresistor (LDR) based line following 2.Individual wheel control 3.Chipset: LM393 4.Material: Electrical components 5.Color: See picture 6.Board Size:10.4*7.2cm The assembly steps: Step 1: Welding circuit - Electric welding part is simpler, welding sequence according to the principle of component level from low to high, the first welding eight resistance is important to use the multi meter to confirm resistance is correct Step 2: Mechanical assembly - The red line is connected to the 3V positive power supply, the yellow line grounding, the excess wire can be used for the motor wire. Step 3: The installation of a photoelectric circuit - Photosensitive resistance and light-emitting diodes (note polarity) is reverse-mounted on the PCB, and the ground distance is about 5 mm, both photosensitive resistance and light-emitting diodes are 5 mm distance. Finally, you can power test. Step 4: Vehicle debugging - The right direction is along the universal wheel direction if you press and hold the left photoresistor - The wheels on the right side of the car should be rotated. Press and hold the right photoresistor - The wheels on the left side of the car should be rotated, if the car driving back, can also exchange the wiring of two motors, if the one side normal and the other side back up, as long as you can swap wiring on the back side. Note: The battery is not included. Package Included: 1 x Base board 1 x 35mm Wheels 1 x Rubber Wheel bands 1 x AA Battery holder 1 x Screw set 1 x LM393 Chipset 1 x 8pin DIP Socket 10 x Resistor 2 x Gearded DC Motors 2 x Electrolytic capacitor 2 x Light dependant resistors 2 x Transitors 2 x White LED 2 x Red LED 1 x Power switch 4 x 70mm Leads

Geekcreit™ DIY T200 NodeMCU Aluminum Alloy Tank Track Caterpillar Chassis Smart Robot Kit Description: A novel design has already coming for the tank chassis, with beautiful shape, and full metal aluminum alloy structure. In this tank chassis, a space for 9g servo is left for the ultrasonic sensor, and a space for MG995 servo is also left to rotate the mechanical manipulator. What’smore, UNO R3 and NodeMCU development boards are also designed to install. In addition, the metal panel can be used to install the wheeled car by install the 25mm and/or 37mm motor frames. Interesting, a LED light is installed to brighten the dark in the night. Under the help of the motor, the tank chassis can be smoothly turn left, right, circle, forward and backward, ect. This tank/car chassis is assembled by ESP8266 WiFi module, Based on which, doit company has already designed and developed the mobile phone App with Android and iOS version. By the Apps, the tank/car chassis can finish some basic functions, such as, forward, left & right, back, and return. Doit company provides the richful documents, including the source code, which can let many developers, lovers, and students to DIY the wanted functions. More details, please see the "download" menu. Some useful download links:   Motor DataSheet for Tank/Car Chassis: http://bbs.smartarduino.com/showthread.php?tid=2039 Chassis Installation http://bbs.smartarduino.com/forumdisplay.php?fid=21 Software manumal http://bbs.smartarduino.com/showthread.php?tid=2036 Android App http://bbs.smartarduino.com/showthread.php?tid=1978 iOS App http://bbs.smartarduino.com/showthread.php?tid=2037 FirmWare http://bbs.smartarduino.com/showthread.php?tid=2013 Motor shield http://bbs.smartarduino.com/showthread.php?tid=6 NodeMCU http://bbs.smartarduino.com/forumdisplay.php?fid=2 Specification:   Name: T200 Intelligent track car/tank chassis Material: aluminum alloy Wheel: metal Track: plastic Product size: about 300 x 220 x 55mm (length x width x height) Weight: 1200g Color: golden yellow Motor Parameters:   Name:25mm gear motor Output speed: 150±10%rpm No_load current: 200mA (Max) Stall current: 4500mA(max) Stall torque: 9.5kgNaN Rated speed: 100±10%rpm Rated torque: 3000gNaN Rated current: 1200mA (Max) Noise: 56dB Working voltage: 9V Outside Shaft Length: 14.5mm Shaft End Play: 0.05-0.50mm Screw Size: M3.0 Dia. Of Shaft phi 4mm, D3.5 Encoder: 2pulses/circle Working voltage for sensor: 5V Shipping List: Chassis:1 pcs Driving wheels: 2 pcs Bearing wheels: 6 pcs Track:2 pcs (can be changed the length) DC motor: 2 pcs LED light: 2 pcs NodeMCU development kit: 1 set 18650 battery box: 1pcs(Batteries not included ) Screws:several Screw tools: 3 pcs

21pcs 7colors ZY-25 Mini Solderless PCB Circuit Test Breadboard Description: Usage: experiment, testing and robot. Color: Yellow, white, cyan, red, blue, green, black Specification: Size dimension: 20mm x 15mm x 12mm Mode: ZY-25 Number of hole: 25 Single side Insulating material: ABS plastic Thickness of insulating layer: general Reinforcing material: composite material Feature: It can be recycled and recycling. It is easy to use this breadboard You can piece the breadboard together in fixed unit Package included: 21 x Breadboard

Description: Usage: experiment, testing and robot. Color: 5pcs yellow breadboard 5pcs white breadboard 5pcs cyan breadboard 5pcs red breadboard 5pcs blue breadboard 5pcs green breadboard 5pcs black breadboard Specification: Size dimension: 20mm x 15mm x 12mm Mode: ZY-25 Number of hole: 25 Single side Insulating material: ABS plastic Thickness of insulating layer: general Reinforcing material: composite material Feature: It can be recycled and recycling.It is easy to use this module You can piece the breadboard together in fixed unit Package included: 35 x Breadboard