Register ck three

Feature: - 1MHz Fast-mode Plus compatible owned 30mA high drive capability on SDA of I2C bus interface to drive highly capacitive bus - Each LED output can be achieved from the fully closed (default) to 4096 (12) between the maximum brightness linear programmable brightness - Software programmable open-drain LED output selection (default is push-pull) of 16 push-pull outputs (5V at 25mA sink can absorb and provide 10mA Source Current), no input function - Programmable output state is in response to an order to change or stop in order to achieve all outputs simultaneously update or byte by byte (byte-by-byte) update output (default "Stop command changes") - Active-low output enable input pin when the pin is high LED outputs can be programmed 0,1 or tri-state (high impedance power-on default) - 6 hardware address pins so that the same I2C devices can be connected to the bus 62 PCA9685 - LED output frequency (all LED) is typically 40Hz to 1000Hz (When the oscillator is 25MHz, the prescaler register default value 1EH will generate refresh rate of 200Hz) - 4 software-programmable I2C bus address (a LED group call (Call) addresses and three LED sub call (Call) address) so that the device can be set in any combination to be addressed at the same time (for example, a register for " all calls (All Call) "then all PCA9634 devices on the I2C bus can be addressed at the same time, while the second register for three different addresses, then the device group on a bus device can 1/3 at the same time be addressed), software can enable and disable I2C bus address - Software reset feature (SWRST Call) makes the device via the I2C bus reset - 25MHz internal oscillator requires no external components - The maximum allowable 50MHz external clock input - An internal power-on reset - In the SDA / SCL inputs with noise filter - Output pin has edge generation rate control - No glitches on power output - Hot-Access - Low Standby Current - Operating voltage range: 2.3V to 5.5V - 5.5V tolerant inputs - It can operate at minus 40 degrees Celsius to 85 degrees Celsius environment - ESD protection exceeds 2000V HBM / JESD22-A114,200V MM / JESD22-A115 and 1000V CDM / JESD22-C101 - JEDEC standard JESD78 into the lock test beyond 100mA Package included: 3 x PCA9685 16 Channel PWM Servo Control Module 3 x Terminal 18 x Pin

This item is sold brand new. It is ordered on demand from our supplier and is usually dispatched in 10 to 15 working days. We urge you to please read shipping details before placing your order. --------------------------------------- Features 1. Adopting the most advanced fingerprint algorithms the identification ability to the fingerprint under the change of environment climate and a finger injury peeling fingerprint has significantly improved and can distinguish in one second under a full fingerprint state 2. We are the first to use the intelligent sensor energy-saving fingerprint reader in the industry along with the advanced power management features can reduce the energy consumption effectively 3.The fingerprints intelligent learning update function can implement registered for one time and use for a whole lifetime that will relieve you from many troubles 4. The using of a 2.8-inch TFT color display will makes your interface operation intuitive and clear 5.Using USB and TCP/IP communication and can also support U disk to download attendance records and fingerprint data and other functions. The users fingerprint can register in one machine register and share by a U disk and no need to connect to a computer in real time 6. The machine has three authentication methods: fingerprint password and ID card 7. The desktop software uses the RIMSOFTs RIMS (Koch) management system it is simple to use intuitive to operate. and with the upgrading and the continuous improvement of our products the user can enjoy the added value of software upgrading all the time --------------------------------------- See what else we're selling

3Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 3 x MAX7219 8 bit digital tube module 12 x Copper pillar 12 x Screws

MAX7219 Red Dot Matrix Module 8-Digit LED Control Display Tube For Arduino MCU is available now from our US   warehouse Free shipping to US  in 3-6 business days ship to Canada, Brazil in 7-10 days MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 1 x MAX7219 8 bit digital tube module 4 x Copper pillar 4 x Screws

5Pcs MAX7219 Red 8 Bit Digital Tube LED Display Module For Arduino MCU Description: MAX7219 is an integrated serial input / output common-cathode display drivers, which connects the microprocessor and 8 bit 7-segment digital LED display, you can also connect a bar graph display or 64 separate LED. Includes an on-chip type B BCD encoders, multi-channel scanning loop, segment word driver, but also a 8x8 static RAM that stores each data. Only one external register is used to set the current of each LED segment. A convenient four-wire serial interface can connect all common microprocessor. Each data can be addressed in the update without rewriting all displays. MAX7219 also allows the user to select each data encoding or no coding. The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan-limit register allows the user to display 1-8 bit data, there is an all LED light detection mode. Feature: 0.36 inch Common cathode Only need three IO ports can drive 8 bit digital tube The module compatible of 5V / 3.3V microcontroller (51 / AVR / STM32...) PCV board four corners of the fixed copper stud, which can effectively precent short circuit accidents happen Wiring instructions (a program, for example, you can pick any IO port definition can be modified in the program): VCC to 5V, GND to GND, DIN to P00, CLK to P02, CS to P01 Note: VCC and GND do not reversed, it would burn the chip. 51 MCU P0 port requires pull-up resistor, if your device does not have a pull-up resistor can be connected to other ports data lines. Package included: 5 x MAX7219 8 bit digital tube module 20 x Copper pillar 20 x Screws

TM1638 Chip Key Display Module 8 Bits Digital LED Tube For AVR Arduino Features: 8 Bits, 8 keys, 8 LEDs, 8 digital tubes, common cathode LED digital tube. With TM1638 Chip, this module gather more than three common SCM peripheral circuits. The advantage is only three IO ports will be occupied when it drives. SCM doesn't need to work for scaning display and key scaning. It only need to read the relevant register to send display data or test button so it save MCU resources effectively. Keys are sensitive and display effectively. Specification: Weight: 28g Material: Glass fiber reinforced plastic, PBT shell, PA blades How to connect: VCC GND 5V power supply, STB CLK DIO SCM IO port. Package included: 1 x LED display module 5 x Dupont line connectors

Features: 8 Bits, 8 keys, 8 LEDs, 8 digital tubes, common cathode LED digital tube. With TM1638 Chip, this module gather more than three common SCM peripheral circuits. The advantage is only three IO ports will be occupied when it drives. SCM doesn't need to work for scaning display and key scaning. It only need to read the relevant register to send display data or test button so it save MCU resources effectively. Keys are sensitive and display effectively. Specification: Weight: 28g Material: Glass fiber reinforced plastic, PBT shell, PA blades How to connect: VCC GND 5V power supply, STB CLK DIO SCM IO port. Package included: 1 x LED display module withe cable

3Pcs TM1638 Chip Key Display Module 8 Bits Digital LED Tube For AVR Arduino Features:8 Bits, 8 keys, 8 LEDs, 8 digital tubes, common cathode LED digital tube.With TM1638 Chip, this module gather more than three common SCM peripheral circuits.The advantage is only three IO ports will be occupied when it drives.SCM doesn't need to work for scaning display and key scaning.It only need to read the relevant register to send display data or test button so it save MCU resources effectively.Keys are sensitive and display effectively.Specification:Weight: 28gMaterial: Glass fiber reinforced plastic, PBT shell, PA bladesHow to connect: VCC GND 5V power supply, STB CLK DIO SCM IO port.Package included:3 x LED display module withe cable

Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 2200W(10A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40￢ﾄﾃ~125￢ﾄﾃ Package included: 1 x TH10 Thermostat Module 1 x DS18B20 Waterproof Temperature Probe

Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 2200W(10A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40ãÄ~125ãÄ Package included: 1 x TH10 Thermostat Module 1 x AM2301 Temperature And Humidity Sensor

Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 3500W(16A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40ãÄ~125ãÄ Package included: 1 x TH16 Thermostat Module 1 x AM2301 Temperature And Humidity Sensor

Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 3500W(16A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40￢ﾄﾃ~125￢ﾄﾃ Package included: 1 x TH16 Thermostat Module 1 x DS18B20 Waterproof Temperature Probe

SONOFF DIY 10A Smart Home WIFI Wireless Temperature Humidity Thermostat APP Rem Package weight: 0.06 kg Manual: It can use with or 16A version: Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 2200W(10A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40￢ﾄﾃ~125￢ﾄﾃ Package included: 1 x Thermostat Module(AM2301 sensor not included) Click here for more deals SONOFF DIY 10A Smart Home WIFI Wireless Temperature Humidity Thermostat APP Rem SONOFF DIY 10A Smart Home WIFI Wireless Temperature Humidity Thermostat APP Rem

Overview: Sonoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicated, the new version Sonoff TH device supports two power supply specifications- 10A or 16A. It supports preset a temperature and humidity range, when the temperature and humidity of the environment falls into the range, it will automatically turn on or turn off connected devices. The device supports connecting to three kinds of temperature and humidity sensors (AM2301, DS18B20, DHT11). Actually, Sonoff TH 10A/16A Sonoff TH 10A/16A can work as a Sonoff when without connecting to sensors. But compared to Sonoff, Sonoff 10/16 is more safer, less radiation and in bigger size, easy operation. Most importantly, with the support of latest ewelink app, you can create chains of simple conditional statements(Smart Scene). This means you can use the them with temperature and humidity sensors (AM2301, DS18B20, DHT11) to collect data, while these data can be shared to other ITEAD smart home devices(Sonoff, Sonoff RF, Sonoff SV, Slampher, smart socket, etc.) under your account, thus other devices can use the data to control connected appliances. This device is perfect to work with electric fan, air conditioner, humidifier. Please note that this version does not have 433 RF function. Features: - Supports 90~ 250V AC input - Support max 10A input - Power: 3500W(16A) - Support fast configure SSID and password connection through APP - Support automatic connect to server, register and update status info. - Support tracking device status and timely remote control through APP - Support setting countdown, single and repeat timing tasks - Support real-time temperature and humidity displaying - Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11) - Support preset temperature and humidity to turn on/off - Support group management, scene, smart scene WIFI Characteristics: - 802.11 b/g/n - Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant frequency support 80 MHz and 160 MHz, support RTOS - Built-in TCP/IP protocol stack - Built-in TR switch, balun, LNA, power amplifier and matching network - Built-in PLL, voltage regulator and power supply management components, 802.11b mode +20 dBm output power - A-MPDU&A-MSDU aggregation and 0.4μs guard interval - WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode - Support cloud OTA upgrade - Support STA/AP/STA + AP mode - Standby power consumption is less than 1.0 mW (DTIM3) - Operating temperature range: -40?ﾃ~125??br /> Package included: 1 x TH16 Thermostat Module 1 x DS18B20 Waterproof Temperature Probe