Pwm pin extension

Description: Using single chip embedded technology; Peak 4.5v to 10V level, jumper inserted at 5V. This level of signal mainly for conventional industrial control card (such as MACH3 board Card) 5V CPU interface; Easy to operate, can be fine-tuned by potentiometer; Select the PWM signal input level range through short cap; Module is small, easy to carry and use; Module operating voltage: DC12V-30V (power requirements: greater than 100mA); PWM signal reception frequency range: 1KHz-3KHz; Peak 12 to 24V level, jumper inserted in the 24V. This level of signal is mainly aimed at the conventional PLC interface; Conversion range: 0% -100% PWM to 0-10v voltage; Allowable error: 5%; Pin Definition: VCC: working power 12-30V GND: ground PWM: input PWM signal positive GND: input voltage ground VOUT: Output voltage: 0-10V GND: output ground Package included: 1 x PWM To Voltage Conversion Module 0-100% PWM To 0-10V Voltage

Feature: 1.OBD II cable splitter, signal splitter 2.Compatible diagnostic tools with a 16 pin socket 3.Allows three devices to be connected simultaneously 4.High-quality materials give the cable superior flexibility and durability 5.This OBD II cable splitter will allow you to split our one OBD II port into three Specification: Product Name Adapter Color Black Material Plastic Head Type OBD 2 Wire 16 Pin With Switch                Extension Length               70 CM Weight 175g Package Included: 1 X OBD 2 16 Pin Extension Cable

1. XLR 3 Pin extension cable, XLR male and 2 female connectors. 2. Great microphone cable for recording studio and live sound. 3. Shielded cable reduces interference and excess noise. 4. It Is compatible with any XLR-microphone, mixer, recorder connection.

FAST AFFORDABLE COURIER SHIPPING TO SOUTH AFRICA Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot

Buy 5Pin Computer CPU PWM Fan Hub Extension Cable 5-pin Motherboard Pair Wiring Fan Concentrator... for R189.00

Feature: - 1MHz Fast-mode Plus compatible owned 30mA high drive capability on SDA of I2C bus interface to drive highly capacitive bus - Each LED output can be achieved from the fully closed (default) to 4096 (12) between the maximum brightness linear programmable brightness - Software programmable open-drain LED output selection (default is push-pull) of 16 push-pull outputs (5V at 25mA sink can absorb and provide 10mA Source Current), no input function - Programmable output state is in response to an order to change or stop in order to achieve all outputs simultaneously update or byte by byte (byte-by-byte) update output (default "Stop command changes") - Active-low output enable input pin when the pin is high LED outputs can be programmed 0,1 or tri-state (high impedance power-on default) - 6 hardware address pins so that the same I2C devices can be connected to the bus 62 PCA9685 - LED output frequency (all LED) is typically 40Hz to 1000Hz (When the oscillator is 25MHz, the prescaler register default value 1EH will generate refresh rate of 200Hz) - 4 software-programmable I2C bus address (a LED group call (Call) addresses and three LED sub call (Call) address) so that the device can be set in any combination to be addressed at the same time (for example, a register for " all calls (All Call) "then all PCA9634 devices on the I2C bus can be addressed at the same time, while the second register for three different addresses, then the device group on a bus device can 1/3 at the same time be addressed), software can enable and disable I2C bus address - Software reset feature (SWRST Call) makes the device via the I2C bus reset - 25MHz internal oscillator requires no external components - The maximum allowable 50MHz external clock input - An internal power-on reset - In the SDA / SCL inputs with noise filter - Output pin has edge generation rate control - No glitches on power output - Hot-Access - Low Standby Current - Operating voltage range: 2.3V to 5.5V - 5.5V tolerant inputs - It can operate at minus 40 degrees Celsius to 85 degrees Celsius environment - ESD protection exceeds 2000V HBM / JESD22-A114,200V MM / JESD22-A115 and 1000V CDM / JESD22-C101 - JEDEC standard JESD78 into the lock test beyond 100mA Package included: 3 x PCA9685 16 Channel PWM Servo Control Module 3 x Terminal 18 x Pin

Description: Multi-functional transistor tester for automatic detection of NPN and PNP transistors, N channel, P channel, MOSFET and JFET, diodes, dual diode, thyristor, automatic identification of the transistor pinout. It also can be used for frequency measurement and PWM signal generator. Features: 1. The processor uses high performance single chip ATmega328 and using external 8MHz oscillator as the system clock. 2. 1.8 Inch LCD screen, resolution is 128X160, Support 65536 colors. 3. Single button operation, support for automatic shutdown to reduce power consumption. 4. Power supply support battery, the current is less than 20nA when the system is turned off. 5. Measurement time of about 2S each time. Measuring time becomes longer when measuring capacitance or inductance. 6. Detection of NPN or PNP Bipolar Transistor automatic, N channel, P channel MOSFET and JFET, diode, Double diode, P-IGPT, Thyristor, Double thyristor etc. For some thyristor and double thyristor. Unable to test When the transistor tester can not meet the requirements of its trigger current and keep the current. Transistor testers are also unable to test the IGPT drive voltages is over than 5V. 7. Support identification pin for test element. 8. Support test current amplification factor for bipolar transistor and base emitter turn-on voltage. 9. Can judge Darlington transistor through the turn-on voltage and the current amplification factor. 10. Support test the gate threshold voltage of MOSFET, grid capacitance and drain electrode in the case of 5V gate voltage- source resistance RDSon 11. Supports the simultaneous measurement of two resistors,Data is four decimal format display. Support potentiometer test, It can not distinguish between the middle pin and this pin When the potentiometer is adjusted to one end of the potentiometer. 12. Minimum resistance resolution 0.01 ohm, Maximum resistance 50M ohms. 13. Can measure a capacitor, Capacitance range 25pf~100mF, Resolution 1pF. 14. Capacitance less than 25pF can be measured by parallel connection another known capacitor is greater than or equal to 25pF. The measured capacitance value can be obtained by subtracting the known capacitance value from the result. 15. When the test capacitance is greater than 90nF, it series equivalent resistance is also be shown, resolution is 0.01 ohm. 16. When the test capacitance is greater than 5000pF. Voltage loss after the test pulse is can be measured.This parameter can estimate the quality factor of the capacitor. 17. Support two diodes to be measured simultaneously and display voltage drop for diode. 18. LED will be identified as a diode, the test voltage drop is much larger than that of the common diode. Two colors diodes are identified as two diodes. 19. Resistance less than 2100 ohm, it’s equivalent inductance is also measured at the same time. Range is 0.01mH~20H, but it’s measurement accuracy is not very good. 20. Program tape self checking function, support calibration of multiple parameters. 21. Support frequency measurement function,frequency signal input from PD4 pin. Frequency resolution is 1Hz when the input frequency is greater than 25KHz. When the value is less than that, by measuring the period, the frequency resolution can be 0.001Hz. 22. Support frequency generator function, output by TP2, the output frequency range is 1Hz ~ 2MHz. 23. Support a fixed frequency signal output from the TP2, the duty cycle can be adjusted by the button. Notice: Before measuring capacitance, the capacitor must be discharged, otherwise very likely damage the meter. Be sure to disconnect the power from the circuit board when testing the components on the circuit board, the test equipment have residual voltage is not allowed. Specifications: Type: Assembled Tester Display: 1.8inch 160*128 LCD Power supply: DC 7-12V Current: Approx. 20mA Resistance measurement: Max. 50MΩ Resistance resolution: 0.01Ω Capacitance measurement: 25pF~100mF Capacitance resolution: 1pF Inductance measurement: 0.01mH~20H PCB size: 7.5 x 6cm / 2.95 x 2.36in Product weight: 50g / 1.79oz Package size: Approx. 10 x 7 x 2cm / 3.94 x 2.75 x 0.8in Package weight: 53g / 1.9oz Package includes: 1 x Transistor Tester English User Manual: Click to open

Features: This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs Package included: 1 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot

Features:   This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1" breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header "Chain-able" design A spot to place a big capacitor on the V+ line (in case you need it) 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial Solder jumpers for the 6 address select pins i2c-controlled PWM driver with a built in clock. Unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages) 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs - that's a lot of servos or LEDs Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate Configurable push-pull or open-drain output Output enable pin to quickly disable all the outputs   Package included: 5 x PCA9685 16-Channel 12-bit PWM Servo Motor Driver I2C Module For Arduino Robot  

Description: Using single chip embedded technology; Peak 4.5v to 10V level, jumper inserted at 5V. This level of signal mainly for conventional industrial control card (such as MACH3 board Card) 5V CPU interface; Easy to operate, can be fine-tuned by potentiometer; Select the PWM signal input level range through short cap; Module is small, easy to carry and use; Module operating voltage: DC12V-30V (power requirements: greater than 100mA); PWM signal reception frequency range: 1KHz-3KHz; Peak 12 to 24V level, jumper inserted in the 24V. This level of signal is mainly aimed at the conventional PLC interface; Conversion range: 0% -100% PWM to 0-10v voltage; Allowable error: 5%; Pin Definition: VCC: working power 12-30V GND: ground PWM: input PWM signal positive GND: input voltage ground VOUT: Output voltage: 0-10V GND: output ground Package included: 3 x PWM To Voltage Conversion Module 0-100% PWM To 0-10V Voltage

Type: JR Plug Servo Extension Wire(Male to Male) Durable hard plastic material. Each cable length:10CM/100MM/3.93inch. Work for:RC Car,plane and helicopter servo connection or receiver connectionthe Like AMP 2.6 flight and Pixhawk controllers There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. This is a simple three wire cable. Black, white and red. 10pcs Servo Extension Cable Lead Wire 100mm 3.93 inch 3 Pin Cord Male to Male JR Plug for RC Plane Product Features: Male to male, 3Pin wire cable. 60wire cores, high quality. 10CM Male to Male JR Plug Servo Extension Lead Wire Cable, 3.93Inch Length, easy connection. Used for RC car, plane and helicopter servo connection or receiver. This is a simple three wire cable. Black, white and red. Great for jumping from board to board or just about anything else. There is a 3-pin JST RE connector on both ends. These are simple jumper wires used on standard 0.1" breakaway headers. Package Including 10 * 100mm Servo extension cable(male to male) Brand name MakerHawk Item Weight 18.1 g Product Dimensions 30 x 1 x 1 cm Manufacturer reference 07ZG1516HGN Wireless Type 802.11abg    

Buy upHere Sleeve Extension Power Supply Cable Kit Power Supply with Extra Sleeved PIN PIN PIN White... for R1,229.00

This Item is Dropshipped !!!!!!!!!!!!!! FREE SHIPPING !!!!!!!!!!!!!! Registered Airmail to your nearest R.S.A Post Ofice on all orders over R300.00 Features: 3 meters of MIDI Extension Cable ensure using flexible. High quality 5 pin male to 5 pin male MIDI extension cable. Screened cable for interconnection of MIDI compatible instruments and controllers. Nickel-plated plugs for rugged durability and efficient signal transfer. Specifications: Color: Silver Length: Approx. 3m / 9.8ft Package size: 20.0 * 14.0 * 2.0cm / 7.87 * 5.51 * 0.79in Package weight: 66g / 2.3oz Package List: 1 * MIDI Cable   click here to view all items To keep our prices as competitive as possible, all our items are shipped directly from our international suppliers, therefore your package may be inspected at customs. Buyers are responsible for any duties / VAT on this item if any is charged which are collected by SAPO on behalf of SARS and is not included in the price.  Shipping takes 30 to 40 business days and could be delayed due to circumstances out of our control.

Description: Working Voltage: DC 5-12V Conversion Range: 0-5V/0-10V to 0-100% PWM Allowable Error: 1-3% Pin Definition: VCC: working power 5-12V GND: ground VIN: input voltage:0-10V GND: input voltage ground GND: output PWM ground PWM: output PWM Package included: 5 x Voltage To PWM Converter Module

Buy 10pcs M5Stack GROVE-TO-4P Extension HY2.0-4P Interface PIN Pin Leads to Dupont Line for R263.00